Q4.A cantilever beam, 50 mm wide by 150 mm high and 6 m long, carries a load that varies uniformly from zero at the free end to 1000 N/m at the wall. (a) Compute the magnitude and location of the maximum flexural stress. (b) Determine the type and magnitude of the stress in a fiber 20 mm from the top of the beam at a section 2 m from the free end.

Q4.A cantilever beam, 50 mm wide by 150 mm high and 6 m long, carries a load that varies uniformly from zero at the free end to 1000 N/m at the wall. (a) Compute the magnitude and location of the maximum flexural stress. (b) Determine the type and magnitude of the stress in a fiber 20 mm from the top of the beam at a section 2 m from the free end.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.5.2P: A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is...

See similar textbooks

Similar questions

Solve following the problems below and show your complete, systematic and neat solution. Upload your solution with one PDF file. 1. For the beam shown, a. determine the maximum flexural stresses in compression ant tension. b. determine the flexural stress of the fiber located at 3m from the left support and 50 mm above the bottom 18 kN/m 300 mm 6 kN/m 20 mm 27 kNm 22 2m 2m 3 m +m 15 mm - - 50 mm 360 mm 20 mm
1. Steel rod 2.5m long is secured between tow walls. If the load on the rod is zero at 20°C, compute the stress when temperature drops to (-20°C). The cross-sectional area of the rod is 1200 mm a=11.7µ m/(m.°C) and E=200 GPa. Solve assuming (a) that the wall is rigid and (b) that the wall spring together a total distance of 0.500mm as the temperature drops. I
Figure shows a beam made from bronze subjected to a 3.5kN.m bending couple and its respective tensile properties. i) With aid of illustration, draw the deformation of the bean and locate the position where the beam experience maximum tensile stress (αmax)t and maximum compressive stress (αmax)c. Accordingly. Determine the magnitude of these two stresses. ii) Sketch the two-dimensional stress distribution acting on point A and point B over the cross-sectional area of the beam as observed from side view. Estimate the magnitude of the stresses at those two points.
A simply supported reinforced concrete beam carries a uniformly distributed load of 12 kN/m on a span of 4 m. The beam has a rectangular cross section 250 mm wide by 450 mm deep, with three 20 mm diameter steel bars placed 60 mm from the bottom of the beam, as shown below. The moduli of elasticity for the concrete and steel are 15 GPa and 200 GPa, respectively. Determine the average tensile stress in the steel and the maximum compressive stress in the concrete at the section of maximum bending moment. 450 mm 250 mm 60 mm
(ohsm 2) b. throps A simply supported beam has a rectangular cross-section of 50 mm wide and 120 mm deep. It is loaded as shown in Fig. 3b. Calculate the maximum stresses and draw the stress distribution diagram. The weight of the beam is assumed negligible. mot dit to sbutingsm s A - 2 m edband Im 10 kN B Fig. 3b 136 say xovbizon 2 m C
Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment point is 4m above it, determine the following:a. Calculate the tension of the cable.b. Determine the diameter of the wire if the allowable stress is 125 MPa.c. If the diameter of the cable is 10 mm, find the deflection of the steel cable.d. If the diameter of the cable is 10 mm, find the vertical displacement of the molder.
Q2: A cast iron beam is of T-section as shown in Fig. The beam is simply supported on a span of 6 m. The beam carries a uniformly distributed load of 2 kN/m length on the entire span. Determine the maximum tensile and maximum compressive stresses. (25 marks) 80mm 15mm 60mm 15mm
The figure below shows a simply supported prismatic beam with an applied uniform load. The labeled points A through E are equally spaced (at the quarter points) along the length of the beam and are located at the top of the beam section. Points A and E may be assumed to be located directly above the supports. Rank the points, from greatest to least, on the basis of the absolute value of normal stress in the beam section.
6.13 A brass rod is a firm fit inside a steel tube 2 cm inside diameter and 4 cm outside diameter when the materials are at 15°C. If the rod and tube are now heated to a temperature of 150° C, calculate the maximum stresses in the brass and steel. Take the coeffi- cient of expansion for steel and brass as 10.8 × 10-6 and 18 x 10-6 per °C respectively. For steel E = 200 GPa and for brass E = 85 GPa. Poisson's ratio for both = 1/3. Neglect longitudinal frictional forces between the rod and the tube. %3D eleo
A double-decker train. EXERCISES 1. A reciprocating steam engine connecting rod is subjected to a maximum load of 65 kN. Find the diameter of the connecting rod at its thinnest part, if the permissible tensile stress is 35 N/mm. [Ans. 50 mm) 2. The maximum tension in the lower link of a Porter governor is 580 N and the maximum stress in the link is 30 Nimm. If the link is of circular cross-section, determine its diameter. (Ans. 5 mm) Тор Contents Simple Stresses in Machine Parts 117 3. A wrought iron rod is under a compressive load of 350 KN. If the permissible stress for the material is 52.5 Nimm, cakculate the diameter of the rod. JAns. 95 mm) 4. A load of 5 kN is to be raised by means of a steel wire. Find the minimum diameter required, if the stress in the wire is not to exceed 100 N/mm. (Ans. 8 mm) 5. A square tie bar 20 mm x 20 mm in section carries a load. It is attached to a bracket by means of 6 bolts. Calculate the diameter of the bolt if the maximum stress in the tie bar is…
1.2 p kN q kN/ m L = 14 m d = 4 m q = 100 kN/m p = 50 kN A В A Simply supported beam is Lm long and is subjected to a uniformly distributed load of q ķN/m applied for the full length of the beam and a concentrated load of p kN of the beam as shown. Draw the free body diagram of the given beam and find the support reactions.
The cross section of a reinforced concrete beam is shown below. It has a modular ratio of 15. If the allowable compressive stress in the concrete is 6 MPa and the allowable tensile stress in the steel is 120 MPa, determine diameter of the three reinforcing steel rods to make the beam an economic section.