Q5 A specimen of magnesium having a rectangular cross section of dimensions(3.2 mm X 19.1 mm) and gage length 63.5 mm is deformed in tension. Using theload-elongation data tabulated as follows load (N) and Extension (mm), Find thestandard mechanical properties.load13802780 5630 743081409870 12850 | 14100143401383012500Ext.0.030.060.120.20.250.641.913.184.455.726.99a) Draw the stress strain curve.b) Find the young modulus.c) Find the proof stressd) Find the ultimate tensile strength.e) Find the fracture stressf) Find the maximum strain.

load extension stress=PA strain=δll 0 0 0 0 1380 0.03…

Q5 A specimen of magnesium having a rectangular cross section of dimension= (3.2 mm X 19.l mm) and gage length 63.5 mm is deformed in tension. Using the load-elongation data tabulated as follows load (N) and Extension (mm), Find the standard mechanical properties

Q5 A specimen of magnesium having a rectangular cross section of dimension= (3.2 mm X 19.l mm) and gage length 63.5 mm is deformed in tension. Using the load-elongation data tabulated as follows load (N) and Extension (mm), Find the standard mechanical properties

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Related questions

Q: The following data was obtained from a tensile te Load (kN) 16 32 56 72 95 110 132 14 Extension (mm)…

Q: Problem 7.1. The aluminum bar (cross section 3 cm x 3 cm) shown the figure below is loaded to its…

A: When the axial load is applied to the specimens or the element of any wood or iron material. It…

Q: The composite member is shown in the figure. If the rigid bar remains horizontal after the loading…

Q: The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor…

Q: During laboratory testing of an 8-inch steel-alloy rod with a cross sectional area of 32in a tensile…

A: To find modulus of elasticity and Poisson's ratio

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: The given data is: Tensile Load on metallic bar (P) = 190 kN Diameter of bar (d) = 16 mm Length of…

Q: Find the Normal Stresses experienced by the Steel, Aluminum, and Bronze section of the given body.…

Q: Getting measurements from Figure 11.20, determine approximate values ofthe following items for plain…

A: Given : Need to determine approximate values of the following items for (i) Plane concrete, (ii)…

Q: A 10.0 mm diameter cylindrical specimen of a bearing bronze material is pulled under uniaxial…

A: given-10.0 mm diameter 1500 N force∆d=0.67 mmn=0.35

Q: A 4 m long steel plate having a cross section of 27 mm by 368 mm is use as a hanger and subjected to…

A: We have to suppose the lateral and longitudnal direction then we have to apply the hooks law onto…

Q: PROBLEM 3 A tensile test is performed on a brass specimen 10mm in diameter using a gage length of…

Q: 50 mm 1 = 13 mm 450 mm 350 mm 50 mm 150 mm

A: Determine the value of the section modulus Sx. 2. Determine the value of the plastic section modulus…

Q: } 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm². If a…

Q: 10/10 FIND STRESS IN Aluminum. IF E st= .200000 MPa, Ealu.=70000 MPa 100 kN

A: The deformation in both the steel and aluminum will be same, to get the stress in the aluminum we…

Q: Calculate Poisson's Ratio for a steel that has a modulus of elasticity E of 30,000,000 psi and a…

A: The given data is: Modulus of elasticity, E=30000000 psi Modulus of rigidity, G=11500000 psi

Q: Question 6 6 of A tension test was performed on a steel specimen having an original diameter of 12.5…

A: Given data, Diameter d = 12.5 mm Length l = 50 mm Area of specimen = 122.7 mm2 1. Modulus of…

Q: A tensile load of 150kN is applied to a round metal bar with a diameter of 16mm and a gage length of…

A: Find a.) Modulus of elasticity (MPa)b.) Poisson's ratio for this metal

Q: A metal rod with 0.5 inch diameter is subjected to 2000 lb tensile load. Calculate the resulting…

Q: Problem 7.1. The aluminum bar (cross section 3 cm x 3 cm) shown the figure below is loaded to its…

A: Procedure: To find the elongation of the bar first we need to find the linear strainε. Then…

Q: A certain material was tested for tension using three different specimens. For each trial, the load…

Q: Impact value is used to measure? А. Hardness В. Toughness C. Wheel load D. Strength

A: To find out the impact value is used to measure.

Q: The cantilever beam shown in the figure below carries a downward load that varies from 300 to 700…

Q: If the modulus of elasticity for a given material is twice its modulus of rigidity, then bulk…

A: Given data : Modulus of elasticity=E Modulus of rigidity=C E=2C

Q: tensile load of 50,000 lb is applied to a metal bar with a 0.6 in. by 0.6 in. cross section and a…

Q: Example: tension test has been conducted on a specimen of steel (Lo=100 mm, Do-20mm) and the…

A: Note:- dear student as per Bartley guidelines we are supposed to answer only first 3 subparts.…

Q: A tensile test is performed on a brass specimen 10mm in diameter using a gage length of 50mm When…

Q: Stress-strain plot for a metal is given below. Determine the following: a) Modulus of elasticity. b)…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Problem # A tensile load of 220 KN is applied to a round metal bar with a diameter of 16 mm and a…

A: Data given: Tensile load = 220 kN = 220 × 103 N Diameter of the bar ϕ= 16 mm gauge length L = 50 mm…

Q: A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile…

A: Solution; The material must be having a yield strength greater than σ=FA=24500 Nπ10*10-3m2=312 MPa…

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gauge length…

A: The Poisson’s ratio is given by,

Q: A specimen of magnesium having a rectangular cross section of dimensions (3.2 mm X 19.1 mm) and gage…

Q: During laboratory testing of an 6-inch aluminum-alloy rod with a cross sectional area of 0.32in², a…

A: Given data : Initial Length (Li)=6 inInitial area (AI)=0.32 in2Tensile load (P)=50000 lbsFinal area…

Q: A cylindrical rod with a diameter of 15.24 mm and a gauge length of 400 mm is subjected to a tensile…

A: Solution

Q: To prevent excessive working load deformation, the ratio of Elastic to Plastic section modulus must…

A: Calculate the ratio of elastic to plastic section modulus, To prevent excessive working load…

Q: Give me right solution A steel bar that is 28 feet long is subjected to a 251 kip load. Maximum…

Q: (b) (i) A tensile test specimen made from 0.4% C steel has a circular cross section of diameter d mm…

Q: The following data were obtained from the tensile test of Aluminum alloy. The initial diameter of…

A: Following is the graph deduced from the given information in the table: Part a. Proportional…

Q: A tensile test specimen of stainless steel alloy having a diameter of 0.495 in. and a gage length of…

A: Given above curve we have to find the modulus of elasticity

Q: A tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: Given data in question Length Diameter Elongation in length and Diameter Load To find out…

Q: tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of…

Q: A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm x 15.9 mm is…

A: Modulus of elasticity can be defined as the ratio of the stress experienced by a body or in a body…

Q: The following data were recorded during a tensile test of a 14.0-mm-diameter mild steel rod. The…

A: solutionArea=π4×D2=π4×142=49π mm2length=L=50 mmstrain=elongationlengthstress=Load area

Q: A drill rod with a diameter of 1/2 in. is made of high-strength steel alloy with a shear modulus of…

A: Given data:

Q: A cylindrical rod 600 mm long and having a diameter 13.2 mm is to be subjected to a tensile load. If…

Q: A rectangular steel bar with given dimensions is subjected to a axial compression. What is the…

A: Explanation given below...

Q: A high strength steel with modulus of elasticity of A N/mm, yield strength of B N/mm2 and crushing…

A: We are required to calculate the ductility of steel

Q: The compound bar containing steel bronze and aluminum segments carries the axial loads shown in the…

A: The compound bar is made of two metals of unequal coefficients of expansion, welded together. It…

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: For the given metal bar,

Concept explainers

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.

Question

Q5 A specimen of magnesium having a rectangular cross section of dimensions
(3.2 mm X 19.1 mm) and gage length 63.5 mm is deformed in tension. Using the
load-elongation data tabulated as follows load (N) and Extension (mm), Find the
standard mechanical properties.
load
1380
2780 5630 7430
8140
9870 12850 | 14100
14340
13830
12500
Ext.
0.03
0.06
0.12
0.2
0.25
0.64
1.91
3.18
4.45
5.72
6.99
a) Draw the stress strain curve.
b) Find the young modulus.
c) Find the proof stress
d) Find the ultimate tensile strength.
e) Find the fracture stress
f) Find the maximum strain.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3 young modulus

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis and procedures for material selection

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
From Data What is Material Ultimate Strength In Mpa. 1 Material Aluminum 2 Form Cylinder ve 3 Diameter 12.8 mm 4 Gauge Length 50.8 mm 5 Tensile Testing To Failure 6. 8 Load (N) Length (mm) 9 0 50.8 10 7330 50.851 11 15100 50.902 12 23100 50.952 13 30400 51.003 14 34400 51.054 15 38400 51.308 16 41300 51.816 17 44800 52.832 18 46200 53.848 19 47300 54.864 20 47500 55.88 21 46100 56.896 22 44800 57.658 23 42600 58.42 24 36400 59.182 25
During a tensile test on a specimen the following results were obtained: Load (kN) 15 30 40 50 55 60 65 Extension (mm) 0.05 0.094 0.127 0.157 1.778 2.79 3.81 Load (kN) 70 75 80 82 80 70 Extension (mm) 5.08 7.62 12.7 16.0 19.05 22.9 Diameter of gauge length - 19 mm Gauge length = 100 mm Diameter at fracture = 16.49 mm Gauge length at fracture = 121 mm Plot the complete load extension graph and the straight line portion to an enlarged scale. Hence determine: (a) the modulus of elasticity; (d) the nominal stress at fracture; (b) the percentage elongation; (e) the actual stress at fracture; (c) the percentage reduction in area; (f) the tensile strength. !116 GN/m2; 21%; 24.7%; 247 MN/m2; 328 MN/m2; 289 MN/m2.] 1.10 Figure 1.24 shows a special spanner used to tighten screwed components. A torque is applied at the tommybar and is transmitted to the pins which engage into holes located into the end of a screwed component. (a) Using the data given in Fig. 1.24 calculate: (i) the diameter D of…
1. The following data were obtained during a tension test of an aluminum alloy. The initial diameter of the test specimen was 0.505 in. and the gage length was 2.0 in. Load (lb) 0 2 310 4 640 6 950 9 290 11 600 12 600 Elongation (in.) 0.00220 0.00440 0.00660 0.00880 0.0110 0.0150 Load (lb) 14 000 14 400 14 500 14 600 14 800 14 600 13 600 Elongation (in.) 0.020 0.025 0.060 0.080 0.100 0.120 Fracture Plot the stress-strain diagram and determine the following mechanical properties: (a) proportional limit; (b) modulus of elasticity; (c) yield point; (d) yield strength at 0.2% offset; (e) ultimate strength; and (f) rupture strength.
The following data was obtained from a tensile test on Load (kN) 16 32 56 72 95 110 132 142 140 135 Extension (mm) 0.2 0.4 0.7 0.9 1.5 2.5 5.0 8.5 10.0 12.0 a specimen of 10mm diameter and gauge length 60mm. Using the graph paper supplied, plot the load-extension diagram and determine: (1) The tensile strength (2) 0.1% Proof Stress (3) Young's Modulus for the specimen
The (G-E) diagram obtained in the tensile test performed on a metal sample with a diameter of 16 mm is as follows. The loads at points A, B and C and the elongation measured on l. 16 cm gauge length were determined as follows: B A B C Load (kgf) 4800 8400 7200 Elongation (mm) 0.192 28.8 38.4 a) Calculate the proportionality limit, modulus of elasticity, tensile strength, maximum uniform elongation, and contraction-elongation ratio of the metal. b) Since the measured diameter of the metal at break is 12 mm, find the constriction ratio and the actual stress at break.
Sample: Malleable Steel (AISI 4145) Original Diameter: 6.14mm Gauge Length: 55 mm Final Length: 68.12 mm Final Diameter: 3.54mm Load (kN) Deformation (mm) Stress (MPa) 12.95 Strain (%) 0.3838 0.54 0.7841 0.95 26.48 1.3899 1.63 1.9485 2.07 3.3090 3.10 4.5821 4.22 5.9359 5.03 7.0340 5.51 8.2413 6.22 10.9446 7.22 13.1951 8.18 12.8228 8.77 12.2583 9.11 12.5915 9.61 13.2536 10.33 13.6636 10.71 13.9772 11.35 14.5433 12.63 15.1155 13.88 15.4970 15.10 15.6484 17.09 15.4031 17.79 14.7655 18.73 13.6721 19.28 10.4617 19.88
During laboratory testing of an 6-inch aluminum-alloy rod with a cross sectional area of 0.32in², a tensile load of 50,000 lbs.is applied. Ifthe cross sectional area decreases to 0.3188in? and lengthens to 6.022 inches, what is the Modulus of Elasticity and Poisson's Ratio? E = 6/ɛ V = = -E(lateral)/ɛ(axial)
From Data What is Material Ultimate Strength In Mpa. 1 Material Aluminum 2 Form Cylinder ve 3 Diameter 12.8 mm 4 Gauge Length 5 Tensile Testing 50.8 mm To Failure 7 8 Load (N) Length (mm) 9 0 50.8 10 7330 50.851 11 15100 50.902 12 23100 50.952 13 30400 51.003 14 34400 51.054 15 38400 51.308 16 41300 51.816 17 44800 52.832 18 46200 53.848 19 47300 54.864 20 47500 55.88 21 46100 56.896 22 44800 57.658 23 42600 58.42 24 36400 59.182 25
a) SOLVE STEP BY STEP IN DIGITAL FORMAT DONT USE CHATGPT For the following structures, calculate -Reactions -Deformation diagrams (individual and general) 5 Ton 8 Ton of 12m A + A 3mt +²/2+42 +42 +42 + -2m 2m bod
A tensile test was conducted on a mild steel bar for construction application in Falcon company’sEngineering Materials lab. The following data was obtained from the test(i) diameter of the steel bar = 3cm(ii) Gauge length of the bar = 20 cm(iii) Load at elastic limit = 250 kN(iv) Extension at a load of 150kN = 0.21 mm(v) failure load = 380 kN(vi) Total extension = 60 mm(vii) diameter of the rod at failure = 2.25 cmDetermine (a) Young’s Modulus, (b) Stress at elastic limit, (c) percentage of elongation,(d) Percentage of decrease in area (d) failure stress
} 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm?. If a tensile load was applied to an aluminum bar to achieve the same lateral (transvers) strain with the former (steel bar), what would be the load? Note: Original dimensions of the two bars are the same (Est = 2.1 x 105 MPa, Eat = 0.703 × 105 MPa, vg = 0.3, vat = 0.33) E = º , v = - Saterat Eaxial Fatuminum™ 3000 N A-500 mm² A=500 mm² Fatuminum=? 3000 N Steel Aluminum