Question 2 5 Points An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1 = 0.8 m; B, = 1.0 m; B;= 0.6 m. Determine the axial load acting on bar B; in kN. 35KN B1 B2 B3 ... 10KN 15KN 30KN (А) 35 (в) 20 c) 10

Question 2 5 Points An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1 = 0.8 m; B, = 1.0 m; B;= 0.6 m. Determine the axial load acting on bar B; in kN. 35KN B1 B2 B3 ... 10KN 15KN 30KN (А) 35 (в) 20 c) 10

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.16P: .16 Three identical, solid circular rods, each of radius r and length L, are placed together to form...

See similar textbooks

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.
A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.
A prismatic bar of length L = 1.8 m and cross-sectional area A = 480 mm" is loaded by forces P{= 30 kN and A = 60 kN (see figure) The bar is constructed of magnesium alloy having a stress-strain curve described by the Ram berg-Osgood equation: 45.000 618 UW id which u has units of mega pascals (MPa). (a) Calculate the displacement 8t- of the end of the bar when the load P:acts alone. (b) Calculate the displacement when the load P, acts alone. (c) Calculate the displacement when both loads act simultaneously.
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
.16 Three identical, solid circular rods, each of radius r and length L, are placed together to form a compression member (see the cross section shown in the figure). Assuming pinned-end conditions, determine the critical load Pcr The rods act independently as individual columns. The rods are bonded by epoxy throughout their lengths so that they function as a single member. What is the effect on the critical load when the rods act as a single member?
A steel column (E = 30 x 103 ksi) with pinned ends is constructed of a W10 x 60 wide-flange shape (sec figure). The column is 24 ft long. The resultant of the axial loads acting on the column is a force P acting with an eccentricity n = 2.0 in. If P = 120 kips, determine the maximum compressive stress ff^ in the column. Determine the allowable load Pallowif the yield stress is ( y =42 ksi and the factor of safety with respect to yielding of the material is n = 2.5.
The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. Ilonger than the tube of length L = 10.52 in. Find the maximum safe load P (in Ib with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.64 sq, in. area of aluminum = 3.04 sq, in. E of copper = 17022171 ksi E of aluminum = 10073078 ksi allowable stress for copper = 19926 ksi allowable stress for aluminum = 10407 ksi Bearing plate 0.005 in. Copper - Aluminum