QUESTION 5 a Prove that the efficiency of rectification in a full wave connection is twice that for half wave connection b. Use ideal diode model to analyze lo and Vo of both diodes. Prove the validity of the diode condition where Di is off and D2 is on for this circuit. 10 ka Ska 15 V | 10 V c. Use your answer in Question 2a to derive the expression for transformer utilization factor.

QUESTION 5 a Prove that the efficiency of rectification in a full wave connection is twice that for half wave connection b. Use ideal diode model to analyze lo and Vo of both diodes. Prove the validity of the diode condition where Di is off and D2 is on for this circuit. 10 ka Ska 15 V | 10 V c. Use your answer in Question 2a to derive the expression for transformer utilization factor.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
Consider the diode circuit shown below. If Vs is a sinewave with a peak amplitude of 12 Volts at 60Hz, and diodes D1 & D2 are considered ideal, sketch the appearance of the waveform at node voltage Vout . Sketch the appearance of the waveform at Vout .
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
29. Does an increase in reverse bias for a Varactor diode cause an increase or decrease in capacitance? 30. If the load current through a SCR (Thyristor) reduces to almost zero, what will be the result?
For the circuit shown in Figure, consider Ideal diodes. If Vs = 19sin wt, Vb = 4 V, the minimum value of output voltage is: Vout at of estion Vs Vb Oa. -4 V Ob. -15 V Oc. -19 V Od. 4 V
Problem # 4 In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VpC e. PIV (Peak Inverse Voltage) 10:1 Dy 1ISV ms Ouiput RL 2.2 k2 D, 50 pF All diodes are IN4001. alleee
Determine the value of RL that will establish maximum power conditions for the Zener diode.
• A Si diode at a temperature of 25°C has VD = 0.7V at Is = 10nA. The temperature is raised to 125°C. 1. Calculate ID at 25°C. 2. What is effect of rise in temperature on VD & IS 3. Calculate ID at 125°C.
5) The figure below illustrates a simple voltage threshold detection circuit. To understand how it operates, we will analyze its behavior based on the simple constant voltage drop model for both diodes. Assume the Zener diode (Z1) only conducts when its breakdown voltage of 10V is reached. Di is a red light emitting diode (LED). Assume it conducts after its forward bias voltage of 1.8V is reached. Vin is unknown. Assume Zj acts as a perfect Zener diode (without series resistance). What voltage does Vin have to reach before there is a current through R¡? What voltage must Vin reach before current flows through R2? Write an equation for the current through Zi in terms of Vin, Rị and R2 that is valid when Vin is high enough for both diodes to be conducting. a. b. c. R2 Vino R1 LED
In this circuit, what will be the voltage peaks of the output, if the input is 20Vp-p sine wave?Note: Use First Approximation/ideal diode model. (+peak, -peak)The choices are: A. 10V, 10V B. -3V, -23V C. 3V, -17V D. 23V, 3V
How PN junction diode works under forward bias and reverse bias condition explain with VI characteristics. Indicate the differences between the characteristics of silicon and germanium diodes and state approximately their cut-in voltages