Question-5 Regarding the IC regulator's operation, what is the state of transistor 1, transistor 2, and the charge warning light in the following condition? Complete the figure by choosing correct words for the blank spaces (1 to 4) from the word group. Ignition switch ON, engine stopped Engine running, under regulated voltage (Normal operation) Stator coil Conditions bring Rotor coil D1 Tr1 Tr1 (1) (3) M-IC IC regulator Tr2 Tr2 (2) OFF IG S L a) ON b) ON and OFF intermittently c) OFF d) Turned on e) Turned off IG Chatge waming light S Ignition switch Turned on (3) (4) Charge warning light Load

Question-5 Regarding the IC regulator's operation, what is the state of transistor 1, transistor 2, and the charge warning light in the following condition? Complete the figure by choosing correct words for the blank spaces (1 to 4) from the word group. Ignition switch ON, engine stopped Engine running, under regulated voltage (Normal operation) Stator coil Conditions bring Rotor coil D1 Tr1 Tr1 (1) (3) M-IC IC regulator Tr2 Tr2 (2) OFF IG S L a) ON b) ON and OFF intermittently c) OFF d) Turned on e) Turned off IG Chatge waming light S Ignition switch Turned on (3) (4) Charge warning light Load

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 12SQ: Referring to the circuit in Figure 412, what circuit component controls the actions of the two CR...

See similar textbooks

Similar questions

When the triac is in the OFF state: Output module terminal strip Triac switch LED output L1 status indicator Fuse Optical isolator, Field wiring Digital logic circuit Load L2 Internal module circuit Simplified diagram for a single output of a discrete AC output module. O the rated nominal current flows through the lamp O the rated surge current flows through the lamp O zero current always flows through the load small leakage current may flow through the load a
Please, in 10 minutes. Will be very THANKFUL. A single-phase half-wave thyristor control is desired to be designed in such a way that a rectifier can provide an average load current of “1.6” Ampere to an ohmic load. “240”Volts, an output voltage of “83”Volts is formed for 50Hz mains supply voltage. According to these given values: a-) Draw a single line diagram of the circuit to be designed? b-) Calculate the trigger angle α? c-) calculate the rms voltage on the load? d-) Calculate the rms current on the load? e-) Calculate the output dc power?
State whether the following statement is true or false. “The efficiency of a switching regulator is always higher than that of a linear regulator.” Please explain.
11. DIAC and TRIAC are similar in that both devices. a. Can use breakover voltage b. can be used in ac circuits c. are bidirectional d. all of the above 12. These are semiconductor devices that are primarily used in electronics as electronically controlled switches a. Diodes b. Transistors c. Vacuum Tubes d. Thyristors 13. If an SCR is suspected of not functioning properly, it should be tested a. with power off b. with multimeter set to the diode or high resistance function c. With the SCR leads isolated d. All of the above 14. A thyristor that looks like two back-to-back 4 layer diodes is the a. SCR b. Triac c. SCS d. DIAC 15. A device that has an unstable negative resistance region is the a. UJT b. SCS c. TRIAC d. DIAC
4aa) This question is about half wave rectifier Half wave rectifier with a reservoir capacitor -> connected -> AC mains supply (220Vrms, 50Hz) by 20:1 transformer. What is the value of capacitor for the ripple voltage of 12% of the peak input voltage? The load's maximum current is 170mA. Show the full working!
kindly answer What are the two types of power supply voltage regulator circuits. Draw the block diagram of these ircuits.
Referring to the circuit in Figure 412, what circuit component controls the actions of the two CR contacts?
Question 6: Look at this PLC on-delay circuit and explain and describe how it will function, in detail, referencing to each component in the circuit shown and how each component will work together to give an off-delay.
1. For the ADC0804 used in section 1. the step size can be adjusted by setting the reference voltage on pin 9. When this pin is not connected (as shown in the figure 1 schematic), the reference voltage is the operating voltage Vcc. a) What is the step size for this default setting? b) How can we set the reference voltage on pin 9. to 4 V? c) What would be the step size after changing the reference voltage to 4 V? 2. Determine the analog input that will result in an output code of "10001110". Assume 5 V reference. Show your calculations. 3. What value of the analog input voltage would result in a digital output is 6F (hex)? Assume 4V reference. Show calculations. 4. In section, you used a 8-bit D/A converter. With a reference voltage of 5 V, what voltage does each bit represent in terms of the analog output? Show calculations. 5. For the D/A converter, if the output is 3.62 V, what is the value of the digital input? Show calculations. 6. For the D/A converter circuit shown in Figure 2,…
A step up chopper has an input of 200 volts and output of 250 volts. The blocking period is each cycle is 0.6x10-3 seconds. Find the period of conduction in each cycle and frequency of operation?
The purpose of the current limiting resistor in a Zener diode circuit is to _________. a. Maintain a constant current through the load resistor b. Maintain a constant voltage across the Zener diode c. Maintain a constant current through the Zener diode d. Drop the additional voltage from the power supply in order to maintain a constant voltage across the Zener diode Please answer it clearly.
A switch that can conduct positive on-state current, and can block positive or negative off-state voltage is called ___. A. voltage-bidirectional two-quadrant switch B. synchronous rectifier C. single quadrant switch D. four-quadrant switch