question 51 An ideal vapor-compression refrigeration cycle that uses refrigerant-134a as its working fluid maintains a condenser at 800 kPa and the evaporator at -12 C. Determine this system’s COP and the amount of power required to service a 150 kW cooling load. What is the mass flow rate of refrigerant in kg/s to 4 decimal places? No need to add units to the answer.

question 51 An ideal vapor-compression refrigeration cycle that uses refrigerant-134a as its working fluid maintains a condenser at 800 kPa and the evaporator at -12 C. Determine this system’s COP and the amount of power required to service a 150 kW cooling load. What is the mass flow rate of refrigerant in kg/s to 4 decimal places? No need to add units to the answer.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter3: Refrigeration And Refrigerants

Section: Chapter Questions

Problem 2RQ: What are the approximate temperature ranges tor low-, medium-, and high-temperature refrigeration...

See similar textbooks

Similar questions

Provide a complete given and computation. Include all the decimals. There are received 68,000 kg/h of steam by an ideal regenerated engine, having only one heater, of which the heater receives 15,400 kg/hr the condenser receives the remainder at 0.007 MPa. If the heater pressure is 0.96 MPa, find the state (quality or "SH) of the steam (a) at the heater entrance and (b) at the condenser entrance.
select if true or false for the following questions 1. For a standard condenser in a refrigeration system, the thermal energy (in J) is equal to the mass (in kg) multiplied by the change in enthalpy across the condenser (in J/kg). 2. Consider a basic refrigeration cycle: Since it requires less work to compress a liquid than a vapor, the entire refrigeration process would work better if the compressor was replaced with a pump. All else being equal, increasing the mass-flow rate of refrigerant will increase the rate of heat transfer at the system’s evaporator. All of these (except, of course, the one labeled, “None of these.”) None of these.
A manufacturing company is intending to use its water cooled condenser for its proposed cold storage room. The name plate of the condenser gives the following specifications: refrigerant ammonia condenser water inlet 30 OC condenser water outlet 40 ỌC condensing temperature 35 OC refrigerant flow 3.84 kg/min circulating water flow 120 kg/min If the company decided to purchase a new compressor and evaporator, find the tonnage of the system and the temperature in the evaporator, (b) what is the COP? (c) find the theoretical hp required.
Provide a complete given and computation. Include all the decimals. Consider a water-ammonia binary vapor cycle consisting. In the steam cycle, superheated vapor enters the turbine at 7 MPa, 450oC, and saturated liquid exits the condenser at 55oC. The heat rejected from the steam cycle is provided to the ammonia cycle, producing saturated vapor at 45oC, which enters the ammonia turbine. Saturated liquid leaves the ammonia condenser at 1 MPa. For a net power output of 24 MW from the binary cycle, determine (a) the rate of heat addition to the binary cycle, in MW, and (b) the thermal efficiency of the binary vapor cycle.
Provide a complete given and computation. Include all the decimals. Consider a water-ammonia binary vapor cycle consisting. In the steam cycle, superheated vapor enters the turbine at 7 MPa, 450oC, and saturated liquid exits the condenser at 55oC. The heat rejected from the steam cycle is provided to the ammonia cycle, producing saturated vapor at 45oC, which enters the ammonia turbine. Saturated liquid leaves the ammonia condenser at 1 MPa. For a net power output of 24 MW from the binary cycle, determine (a) the mass flow rates for the steam and ammonia cycles, respectively, in kg/s, (b) the power output of the steam and ammonia turbines, respectively, in MW. (c) the rate of heat input to the ammonia cycle, in MW,
Thermodynamics (Jet-Propulsion Cycle) Round up the answer up to 5 decimal places. A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure & temperature is found to be 14.7psi & 546R. The axial flow compressor provides a pressure ratio of 14 to 1. Temperature at the turbine inlet is 2000R. The mass flowrate of air inside the engine is 133 lbm/s. Determine the following: a. T-S diagram b. Pressure & temperature at each state c. Thrust force (lbf)
QUESTION 53 An ideal vapor-compression refrigeration cycle that uses refrigerant-134a as its working fluid maintains a condenser at 800 kPa and the evaporator at -12 C. Determine this system’s COP and the amount of power required to service a 150 kW cooling load. Refer to Q5 file case 2. What is the coefficient of performance to 1 decimal place?
QUESTION 1 A 120-ton capacity chiller, based on a refrigeration cycle, is used to maintain a coolant temperature of 35 deg. F. The chiller exchanges heat to the surrounding air at 70 deg. F. This unit utilizes a 150 hp motor. What is the rate of heat removal from the coolant, in Btu/hr? O1,440,000 O 381,675 O 1,821,675 O 120 QUESTION 2 A powerplant operates between a furnace at 990 deg. Fand cooling water delivered from a nearby river at 70 deg. F. What is the maximum possible efficiency of this powerplant, in %? Oa. 72.8% Ob. 27.2% Oc 92.9% Od.63.4% QUESTION 3 If fuel oil is supplied to a power plant furnace at a rate of 60,000 gallons/hr, and the oil has a heating value of 150,000 Btu/gallon, and the plant has a thermal efficiency of 30%, what is the power output of this plant (in MW)? Oa. 2637.6 Ob.9000 Oc 2700 d. 791.3
A heat engine is operating at a heat source of 950 K. The efficiency was calculated to be around 45% so it is desired to increase it to 55%. What should be the temperature of the heat source to effect this change, if the heat sink is kept constant? Assume carnot cycle for the heat engine. *Round off all answers to four decimal places*
Question#1 Pressure-enthalpy chart is another method to obtain an initial performance estimation of refrigeration/heat pump cycles used in heating, ventilation and air-conditioning (HVAC) system. Your role is to provide design and installation services for air -conditioning (AC) system a preliminary performance estimation. Given the following design specifications: Refrigerant HFC-134a as the working fluid - Ideal cycle operation condition is assumed - Cycle is operated at high pressure line of 0.8 MPa - Cycle is operated at low temperature line of – 10° C Flow rate is 0.1 kg/sec The head of the department in the company that you are working in asked you to make use of pressure -enthalpy chart provided for HFC-134a refrigerant Task.1 1. Determine the Refrigeration effect (RE), heat of compression (HOC), and heat of rejection (HOR) and their corresponding rate/power values in kW.
Question#1 Pressure-enthalpy chart is another method to obtain an initial performance estimation of refrigeration/heat pump cycles used in heating, ventilation and air-conditioning (HVAC) system. Your role is to provide design and installation services for air -conditioning (AC) system a preliminary performance estimation. Given the following design specifications: Refrigerant HFC-134a as the working fluid - Ideal cycle operation condition is assumed - Cycle is operated at high pressure line of 0.8 MPa Cycle is operated at low temperature line of – 10° C Flow rate is 0.1 kg/sec The head of the department in the company that you are working in asked you to make use of pressure -enthalpy chart provided for HFC-134a refrigerant Task.1 2. Estimate the COPR 3. Determine the low-pressure line value.
Three water coils are connected in parallel. The water supplied to the coils feeds into a commonreturn line. The first coil feeds 60 gpm of 125 o F water into the return line. The second coil feeds 50gpm of 120 o F water into the line. The third coil feeds 50 gpm of 118 o F water into the commonreturn line. What is the temperature of the water in the common line after the three streams ofwater mix?