QUESTION 8 A torque T is applied on an aluminium shaft acting at the ends (see figure). The shaft is 1.2 m long, and has a solid circular cross-section with diameter of 30 mm. Assuming that shear modulus is G= 28 GPa, and the angle of twist is 4.4°, calculate is the maximum shear stress. T. Find your answer in N/m2.

QUESTION 8 A torque T is applied on an aluminium shaft acting at the ends (see figure). The shaft is 1.2 m long, and has a solid circular cross-section with diameter of 30 mm. Assuming that shear modulus is G= 28 GPa, and the angle of twist is 4.4°, calculate is the maximum shear stress. T. Find your answer in N/m2.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.5P: A tubular bar with outside diameterd2= 4.0 in, is twisted by torques T = 70,0 kip-in. (see figure)....

See similar textbooks

Similar questions

A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
A thin tubular shaft with a circular cross section (see figure) and with inside diameter 100 mm is subjected to a torque of 5000 N · m. If the allowable shear stress is 42 MPa, determine the required wall thickness t by using (a) the approximate theory for a thin-walled tube and (b) the exact torsion theory for a circular bar.
A thin-walled steel tube having an elliptical cross section with constant thickness t (see figure) is subjected to a torque T = 18 kip-in. Determine the shear stress and the rate of twist in degrees per inch) if G = 12 × 106 psi, t = 0.2 in., a = 3 in., and b = 2 in. Note: See Appendix E, Case 16, for the properties of an ellipse.
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A tubular bar with outside diameterd2= 4.0 in, is twisted by torques T = 70,0 kip-in. (see figure). Under the action of these torques, the maximum tensile stress in the bar is found to be 6400 psi. Determine the inside diameter rtf of the bar. If the bar has length L = 48.0 in. and is made of aluminum with shear modulus G = 4,0 × 106 psi, what is the angle of twist d (in degrees) between the ends of the bar? (c) Determine the maximum shear strain y (in radians)?
A stepped shaft consisting of solid circular segments having diameters D1= 2.0 in, and D2= 2.4 in. (see figure) is subjected to torques T. The radius of the fillet is R = 0,1 in. If the allowable shear stress at the stress concentration is 6000 psi, what is the maximum permissible torque Tmax?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (see figure), (a) If the allowable shear stress in the shaft is 43 MPa, what is the maximum torque (T0)max that may be applied at section C? (b) Find (ï^),^ if the maximum angle of twist is limited to 1.85', Let G = 28 GPa.
A torque T is applied to a thin-walled tube having a cross section in the shape of a regular hexagon with constant wall thickness t and side length b (see figure). Obtain formulas for the shear stress rand the rate of twist
A uniformly tapered aluminum-alloy tube AB with a circular cross section and length L is shown in the figure. The outside diameters at the ends arc dAand dB= 2dA. A hollow section of length LB and constant thickness t = dA/10 is cast into the tube and extends from B halfway toward A. (a) Find the angle of twist é of the tube when it is subjected to torques T acting at the ends. Use numerical values: dA= 2.5 in., L = 48 in., G = 3.9 × 106 psi, and T =40,000 in.-lb. (b) Repeat part (a) if the hollow section has con stant diameter rfj (see figure part b)