Refer to the figure. The net excavation (yd³) from Station 1+00 to Station 3+00 is most nearly:(A) 160(B) 262390463STA 1+00C=150 ft²F=0STA 2+00C=50 ft²F = 0STA 3+00C=0F = 40 ft²

Given the details of the earthwork in the following figure. The net excavation from Station 1+00 to…

Answered: Refer to the figure. The net excavation…

Refer to the figure. The net excavation (yd³) from Station 1+00 to Station 3+00 is most nearly: (A) 160 (B) 262 (C) 390 463 STA 1+00 C= 150 ft² F=0 STA 2+00 C=50 f1² F=0 STA 3+00 C=0 F = 40 ft²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 6m simply supported beam with 2 m overhang carries an ultimate load of 45 kN/m. Use f'c-35 MPa and…

A: Simply supported beam, L=6 m Overhang length, a=2 m Ultimate load, wu=45 kN/m fc = 35 MPa fy = 400…

Q: How high should a helicopter pilot rise at a point A just to see the horizon at point B, if the…

A: Distance between two points A & B d=40 km, To Find- The height of the helicopter h to see the…

Q: Prob-5 Hospital workers who are routinely involved administrative radioactive tracer to patients are…

A: Given; Sample size n = 28 sample mean x bar = 5.145 sample std dev s = 0.7524

Q: Estimate the G.I. of sub-grade soil from the following data: (i)Passing 425mic = 72% (ii)Passing…

A: Given (i)Passing 425mic = 72% (ii)Passing 75mic = 55% (iii)Liquid limit = 39% (iv)Plastic limit =…

Q: If the stopping distance and average length of a vehicle are 18 m and 6 m respectively, then the…

A: SSD = 18 m Length of vehicle = 6 m Speed = 10 m/sec = 36 km/h

Q: Annual rainfall at a given location can be described by a normal distribution with a mean of 127 cm…

Q: USE SLOPE DEFLECTIONS METHOD Formula Should follow: Mnf= FEMnf+ 2EI/L ( 2θn + θf - 3r) Determine…

A: Support B settle by 0.5in. E = 29000 ksi I = 1650 in.4 Determine the support reaction and draw…

Q: FROM THE FOLLOWING DATA OF SOIL SAMPLE x 7.62 cm height. SAMPLE SIZE: 3.81 cm WEIGHT: 1-668 N…

A: Question-1 Porosity (n) = 35% Specific gravity (Gs) = 2.7 Determine the void ratio. Question-2…

Q: 5) Use the method of SECTIONS to find the true magnitude and direction in bar HG of the truss shown…

A: To find force in member HG

Q: 6-10. Solve Prob. 6-9 using the Müller-Breslau principle. | -6 m + A -6 m- C + -6 m-

Q: Draw the shear and bending moment diagrams for the beam and loading shown. 20 kN 10 kN A V B 2 m 2 m…

A: Overhang beam with UDL and point loads respectively,

Q: Determine D10, D30, D60, Cu and Cc of the following soils.

A: Soil A Soil B Soil C sieve No. sieve size in mm % finer % finer % finer 4 4.75 84.231 100…

Q: Observed N-value of an SPT test is 21. The N-value after correcting for dilatancy is 1. 18 2. 21 3.…

A: Observed N-value of an SPT test, No=21.

Q: Use LRFD and select a W shape with a nominal depth of 12 inches (a W12) to resist a dead load of 150…

A: LRFD nominal depth, d= 12 in Dead load, DL= 150 kips Live load, LL= 200 kips Diameter of bolts, db =…

Q: A beam AB is fixed at both ends and carries a uniformly distributed load of intensity per unit…

A: We have to determine the percentage increase in bending moment at A

Q: Design a valley curve at the junction of a downward gradient of 1 in 30 and a level stretch from…

Q: A cylinder contains 12.5 ft³ of air at 120 °F and 40 psia. The air is then compressed to 2.50 ft³.…

A: A cylinder contains 12.5 ft3 of air at 120 oF and 40 psia. Th air is then compressed to 2.50 ft3.

Q: What is the total number of unknowns if determining the reactions at points A, B, C, D, and E? C 250…

Q: structures method of sections algebra,geometry and trigo

A: Consider Moment equilibrium at point D Fy*18 = 13*6+9*x tan50 = x6 x = 6*tan50 x = 7.15' Now Fy*18 =…

Q: Situation 6. For the cantilever beam shown in the figure, draw the shear and moment diagram and…

Q: For the given concrete mix design below, calculate the field weight of the ingredients in kg's if…

A: Mass of cement = 300 kg/m3 Mass of water = 150 kg/m3 SSD mass of coarse aggregate = 1020 kg/m3 SSD…

Q: Q1/ (a) The soil profile at a building site consists of dense sand up to 2m depth, normally loaded…

Q: 4. The average spacing between vehicles in a traffic veh/km) of the stream is O A. 10 O B. 20 O C.…

Q: Through a very narrow gap of height 'h a thin plate of large extent is pulled at a velocity V. On…

A: The given situation of the question is shown below in the diagram- It is needed to find the…

Q: 25: Shear strength parameters of N.C. clay sample are: Ø = 15°, 6 = 30° a- In a CU test on the same…

A: Clay samples; ϕ=15oϕ'=30o The confined pressure, σc= 150 kN/m2 Normal stress, σ=100 kN/m2 The…

Q: 9-15. Determine the reactions at the supports, then draw the moment diagram for each member. El is…

A: The given frame is statically indeterminate of degree 1. Therefore to determine the support…

Q: 15.6 Solve Problem 15.2 for the loading shown in Fig. P15.2 and a settlement of in. at support B. A…

Q: 3. The figure is a section of a masonry dam resting on a foundation and subjected to water pressure…

Q: A raft of 5m x 8m is founded at a depth of 3 m in a cohesive soil having c = 120 kN/m². The ultimate…

Q: An extended layer of soil with homogeneous rounded grains has 10% of the material finer than 0.007…

A: An extended layer of soil- 10% of the material finer than 0.007 mm. Constant C=750, To Find- The…

Q: A solid circular shaft of 6m length is built in at its ends and subjected to an externally applied…

Q: Find the Reaction Values of supports , And Draw Shear force Digram And Beanding momeny

A: Draw free body diagram of beam Consider moment equilibriumat B RD * 4 = 30*2 + 30 + 12*5*4*4+23*4…

Q: Use SLOPE DEFLECTIONS METHOD determine the member end moments of the beam of the rectangular cross…

Q: From the truss shown, design all the tension members using an unequal leg angle with a b of 127mm…

Q: 6-3. Draw the influence lines for (a) the moment at C, (b) the vertical reaction at A, and (c) the…

Q: A 4 inch thick rubber pad sandwiched a plate as shown in the figure. Find the displacement (in…

A: Thickness of rubber pad , c = 4in , Load Applied , P =2592lb , E = 500psi , v = 0.53 , a = 9.7in , b…

Q: Determine approximately, the reactions at A, B, C, and D. Use portal frame method.

Q: Draw a neat, fully annotated shear force and bending moment diagram, including the maximum in span…

A: The loading diagram is shown below. Hint : Horizontal distance of BD=3 cos45°=2.12 mVertical…

Q: 6-7. Draw the influence line for (a) the moment at B, (b) the shear at C, and (c) the vertical…

A: A beam with vertical roller support at A such that it resists only moment and horizontal force and a…

Q: Direction: An activated sludge system (sketched below) is operating at equilibrium with the…

Q: Determine the load of W required to cause collapse of the frame if the plastic moment of all members…

A: Plastic Moment, Mp = 200kNm To Find: Magnitude of Load, W

Q: consider the moment-resisting frame. Use the portal method of analysis. Use P2 = 4 kips…

A: To find- What is the shear force in the bottom beams (absolute value)? What is the shear force in…

Q: 1.) A hollow shaft 4m long transmitted a torque of 25 kN-m. The total angle of twist in this length…

A: Given data in question Length 4 m Rotation 3 degree Maximum shear stress 80 Mpa Modulus of rigidity…

Q: This question is in Advanced Soil Mechanics A sand sample with = 1.95, λ = 0.04, M = 1.4, is…

A: Given; τ = 1.95 λ = 0.04 M = 1.4 Axial stress = 200 kpa radial stress = 50 kpa Specified volume…

Q: 11. The rectangular plate is made up of 1-ft squares as Shown. A 30-lb force is applied at point A…

Q: A 20 m chain was found to be 10 cm too long after chaining a distance of 2000 m. It was found to be…

A: 20 m chain found to be 10 cm too long, 18 cm too long at the end of the day's work. Total chaining…

Q: The reaction of the ground is uniformly distributed. Draw the shear and bending moment diagram for…

A: ###Calculation for SF and BM and Drawing of SFD and BMD ####

Q: 9 Simply supported beam of 16m span/ subjected to Live Load as 50 KN/m of Length 4m, by using…

Q: The beam supports a uniform dead load of 500 N/m and a single live concentrated force of 3000 N.…

A: Given Data Dead load = 500 N/m Concentrated Live load = 3000 N Find a. Maximum positive moment…

Q: A discharge of 0.6 m³/s flows through a horizontal bend as shown in figure. Calculate the force on…

A: Given; Discharge (Q) = 0.6 m3/s Dia. at section 1 = 15 cm = 0.15 m Dia. at section 2 = 5 cm = 0.05 m…

Question

Refer to the figure. The net excavation (yd³) from Station 1+00 to Station 3+00 is most nearly:
(A) 160
(B) 262
390
463
STA 1+00
C=150 ft²
F=0
STA 2+00
C=50 ft²
F = 0
STA 3+00
C=0
F = 40 ft²

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Step 1 To determine

VIEW

Step 2: Step 2 Average End Area Method

VIEW

Step 3: Step 3 Computation of net excavation

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q4: For the data tabulated, calculate the volume of excavation in cubic yards between stations 10 + 00 and 15 +00. Cut End Station Area (ft) 10 + 00 263 11 + 00 358 12 + 00 13 + 00 446 402 274 14 + 00 15+ 00 108
Station Cut End Area (ft²) 10+00 234 11+00 369 12+00 441 13+00 408 14+00 271 15+00 108 Part A For the data tabulated, calculate the volume of excavation between stations 10+00 and 15+00. Express your answer in cubic yards to five significant figures. IVE ΑΣΦ V₂ = Submit Provide Feedback Request Answer vec ? yd³
The end area at station 36+00 is 305 ft2. the end area at station 36+60 is 181.08 ft2. What is the volume of excavation? Answer will be in yards cubed, round to the nearest whole cubic yard. 540 1620 1618 500 0000
Station Cut End Area (ft²) 10+00 238 11+00 353 12+00 450 13+00 408 14+00 265 15+00 104 Part A For the data tabulated, calculate the volume of excavation between stations 10+00 and 15+00. Express your answer in cubic yards to five significant figures. Ve= ΕΠΙ ΑΣΦ ΑΣΦ | Π vec w ? yd³
Q3: Figure (3) represent the plan of an area to be excavated, which have been leveled in the form of a square and triangle grid the surface levels are shown beside each point, the grid squares are 20 m on a side, and the required formation level is 20.00 m above datum .Compute the amount of excavation in cubic meters. 28.11 28.24 27-58 2769 27-32 20.00 2763 20.00 Figure (3) 20.00 87.76
2. Complete the profile level notes shown below, perform the customary arithmetic check, provide a detailed sketch, and a detailed solution. STA BS HI FS IFS ELEV BM25 0+ 000 5.3650 254.1458 2.3225 2+ 000 1.3256 4+ 000 2.8945 6+ 000 1.9978 TP, 4.2544 5.4444 8+ 600 1.6452 10 + 200 6.5874 12 + 500 5.8942 14 + 900 5.6100 16 + 300 3.2542 18 + 700 2.6540 TP2 2.0021 6.5566 16 + 200 7.4845 18 + 850 4.5100 20 + 300 5.8900 22 + 070 3.2010 BM26 5.6412
Calculate the end areas for depths of fill from 0 to 20 ft using increments of 2 ft for level sections, a 26-ft-wide level roadbed with side slopes of 1-1/2:1. Part G What is the end area for the depth of 12 ft? Express your answer in feet squared as an integer. End Area = Part H 195| ΑΣΦ. 41 End Area = What is the end area for the depth of 14 ft? Express your answer in feet squared as an integer. vec 96 IVE ΑΣΦ | vec ? ? ft² ft²
Calculate the end areas for depths of fill from 0 to 20 ft using increments of 2 ft for level sections, a 26-ft-wide level roadbed with side slopes of 1-1/2:1. Part I What is the end area for the depth of 16 ft? Express your answer in feet squared as an integer. End Area = Part J 197| ΑΣΦ | 11 End Area = vec What is the end area for the depth of 18 ft? Express your answer in feet squared as an integer. [Π| ΑΣΦ ↓↑ vec ? ? ft² ft²
>Example3/ The following offsets are taken from a chain line to an irregular boundary towards right side of the chain line. Chainage 0 25 Offset 'm' 3.6 5.0 Calculate the area using 1. Trapezoidal Method 2.Simpson's method 50 6.5 75 5.5 100 7.3 125 6.0 150 4.0
2. The following equations were established for a study area. T=40+ 489x, -0.004x,-02-0.017. (1₂=5₁4₂=3,1₂=9.44 = 1.2, R² = 0.69) (r = 25, R² = 0.45) where T = 30 + 5.9X₁ T = 300 +0.25X₂ T = 25 +2.4X₁ + 0.15X₂ (t = 41, R² = 0.23) X, = family income ($1000) (4= 35,4 = 95, R² = 0.85) T= trips/household X₁ = vehicle ownership (cars/household) X₂ = population density (persons/acre) = distance from the CBD (miles) 175 be The number of observations used in setting up these equations is 53. (R² and 1-tests results are also given.) Comment on the reasonableness and logic of these equations for use in this study.
The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 13+8300 7.35 50 57.8 3.97 66 43.1 Determine the cross sectional area at STA 13+8300. Round your answer to 3 decimal places.
Compute the volume of excavation between station 24+00, with an end area of 711 ft2, and station 25+00 with an end area of 515 ft². Answer will be in yards cubed, round to the nearest whole cubic yard. 2270 2720 61290 20430 000