Required information An excellent approximation for the two-dimensional incompressible laminar boundary layer on the flat surface in the given figure is uzU (2 - 2 +) for y s, where o = Cx/2, c = const. Layer thickness 8(x) U U = constant JU u(x, y) Ju(x, y) ind the maximum value of v at the station x=1 m, for the particular case of airflow, when U=7 m/s and o = 1.1 cm.

Required information An excellent approximation for the two-dimensional incompressible laminar boundary layer on the flat surface in the given figure is uzU (2 - 2 +) for y s, where o = Cx/2, c = const. Layer thickness 8(x) U U = constant JU u(x, y) Ju(x, y) ind the maximum value of v at the station x=1 m, for the particular case of airflow, when U=7 m/s and o = 1.1 cm.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.70P

See similar textbooks

Similar questions

1. In the figure shown below, choose whether the statement is true or false (Please justify your answer) (a) At a give x-location, if Re were to increase, the boundary layer thickness would decrease. (b) As upstream velocity decreases, so does the boundary layer thickness (c) As the kinematic viscosity increases, so does the boundary layer thickness (d) As the fluid density decreases, so does the boundary layer thickness (e) As the x-location increases, so does the boundary layer thickness
An air whose cross-sections are visible in the figure on the side Channel 40 cm diameter and 60 cm tall test section references The air temperature is 200oC. At the entrance of the Test section A uniform airspeed of 2 m/s was measured.a) the number of Reynolds at the end of the test section (Rex)calculate.b) limit layer thickness at the end of the test sectioncalculate.c) air velocity test on centerlinewhat percentage increases by the end of the section,calculate.d) local surface friction at the end of the test sectioncalculate the coefficient. v = 1,516 . 10-5 m2/s.
9 of the diffusion Term of The The Expression below is part Nallier-Stokes equation in spherical coordinates. what are units of this term I given it is dynamic viscosity [Pa-s] T A partial derivative behave the same as a full devevarive. 2 дио r² sin(0) do unit ? Expression: anshuar: T ris position, is velosity: A does not have dimension Mf-
(k-1.33) flows inside a goo conseigat/dhiyeget An ideal wher noz2le under certaiu circumstauces " the cross-sedtiou of the noz2le is 2s cu?, Mace nuuber is 2.4. What is the cross-seetion where Mach uuuber = 3.5 - 3. %3D - /1
A rectangular block of height Land horizontal cross-sectional area A floats at the interface between two immiscible liquids, as shown below. Fluid 1 Pi(g/em³) Fluid 2 Block P:(g/cm³) Po(g/cm³) (a) Derive a formula for the block density, Pp, in terms of the fluid densities p, and p2, the heights họ. h1, and h2, and the cross-sectional area A. (It is not necessary that all of these variables appear in the final result.) (b) Force balances on the block can be calculated in two ways: (i) in terms of the weight of the block and the hydrostatic forces on the upper and lower block surfaces; and (ii) in terms of the weight of the block and the buoyant force on the block as expressed by Archimedes' principle. Prove that these two approaches are equivalent.
In the study of turbulent flow, turbulent viscous dissipation rate ? (rate of energy loss per unit mass) is known to be a function of length scale l and velocity scale u′ of the large-scale turbulent eddies. Using dimensional analysis (Buckingham pi and the method of repeating variables) and showing all of your work, generate an expression for ? as a function of l and u′.
Solve using Euler's law the boundary representation model for the below-mentioned diagram.
Consider a boundary layer growing along a thin flat plate. This problem involves the following parameters: boundary layer thickness ? , downstream distance x, free-stream velocity V, fluid density ? , and fluid viscosity ? . The number of primary dimensions represented in this problem is (a) 1 (b) 2 (c) 3 (d ) 4 (e) 5
An important parameter in fluid flow problemsinvolving thin films is the Weber number (We) which canbe expressed in equation form.where p is the density of the fluid, v is a velocity, L is alength, and O" is the surface tension of the fluid. If the Webernumber is dimensionless, what are the dimensions of thesurface tension O"?
Q4) Set up the differential equations for the two masses [Fig.1] 2cos (3t) Fig. 1 C1 K1 M1 K2 М2 K3
Define dimensional homogeneity.
choose whether the statement is true or false and discuss your answer briefly. Kinematic similarity is a necessary and sufficient condition for dynamic similarity.