Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The pin at B is attached to member ABC and can slide freely along the slot cut in the fixed plate. Neglect the effect of friction. P 10 in B 6 in. 8 in. Determine the couple M required to hold the system in equilibrium when 8 = 30° and P = 40 lb. The couple M required to hold the system in equilibrium when 0 = 30° is Ib-in.

Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The pin at B is attached to member ABC and can slide freely along the slot cut in the fixed plate. Neglect the effect of friction. P 10 in B 6 in. 8 in. Determine the couple M required to hold the system in equilibrium when 8 = 30° and P = 40 lb. The couple M required to hold the system in equilibrium when 0 = 30° is Ib-in.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.59P: The weight of the uniform bar AB is W. The stiffness of the ideal spring attached to B is k, and the...

See similar textbooks

Similar questions

The weight of the uniform bar AB is W. The stiffness of the ideal spring attached to B is k, and the spring is unstretched when =80. If W=kL, the bar has three equilibrium positions in the range 0, only one of which is stable. Determine the angle at the stable equilibrium position.
Draw the FBDs for the beam ABC and the segments AB and BC. Note that the two segments are joined by a pin at B. Count the total number of unknowns and the total number of independent equilibrium equations.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
30 in. 40 in. A F 25 in. 45 in. 35 in. Show Transcribed Text 60° A thin U-shaped member is kept in equilibrium in the vertical plane by up to three fingers and the cord (gravity acts downward). The weight of the member is uniformly distributed with 0.1 lb/in. So the total weight is 17.5 lb. Neglect the thickness of the member and any friction between the fingers and the member. Assume the finger force at G is zero. Determine the cord force and the other finger forces.
Find the support reaction at A and the tension at the rope from the beam shown bellow. The pulley is frictionless. Given: a = 8 ft, b = 4 ft, c = 2 ft, r = 6 in, w1 = 1500 lb/ft. Note: Draw the free body diagram and answers should be in 3 decimal places.
Equilibrium.pdf 3/17: The uniform beam has a mass of 50 kg per meter of length. Compute the reactions at the support O. The force loads shown lie in a vertical plane. dns. Or -0.7 AN, Oy- 5.98 AN, Mo 9.12 kN.m 14 kN 3 kN 4 kN m de A 0.6 m 1.8 m 0.6 m 0.6 m 30 7 ENGINEERING MECHANICS: STATICS (J.L.MERIAM) 3/15: Three cables are joined at the junction ring C. Determine the tensions in cables AC and BC caused by the weight of the 30-kg cylinder. Ans.Ic=215 N. I=264 N 45 18 30 30 kg 3/14: To facilitate shifting the position of a lifting hook when it is not under load, the sliding hanger shown is used. The projections at A and B engage the flanges of a box beam when a load is supported, and the hook projects through a horizontal slot in the beam. Compute the forces at A and B when the hook supports a 300-kg mass. dens..d4.9 AN. B19AN 400 600 mm 3/53: Determine the external reactions at A and F for the roof truss loaded as shown. The vertical loads represent the effect of the supported…
Required information In the given figure, all pulleys are frictionless. Take the value of P to be 220 lb. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. P 0.5 ft P0.58 --20-20-20- Determine the reactions at point A and the force supported by the cable. (Do not include a minus sign in your response.) The horizontal component of the reaction force at A is lb →. The vertical component of the reaction force at A is The tension in the cable is lb. lb 1.
Frames & Machines The truck shown is used to deliver food to aircraft. The elevated unit weighs 2000 Ib with center of gravity at G. 1- Derive the expression for the force in the hydraulic cylinder AB as a function of 0 (the angle that member FD makes with the horizontal). 2- Plot the force over the range 0° < 0 < 45° and discuss your observations. Note: | would suggest that you first solve the problem based on the position (angle) shown. You will need to determine the length of members FD and FB before solving the problem for arbitrary 0. Note that the location of the roller at D and hence the force reactions will change as 0 varies. 40" 17" 57" C 54" E 54" H AB
Figure 1: For the frame shown, determine the magnitude of the pin reaction at B. Neglect the weight of the frame. (2 decimal point, indicate the answer in kN. Ex: 3.87kN just encode 3.78)
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
Problem 6 Compute the reaction forces in B and D. After solving the problem, answer the following question: "Is the force in D directed toward the right or direction? Does it make sense and why?" 8.4 kN f 8.4 kN D 2.8 m 4.5 m 4.5 m left
Determine the additional mass required for stable equilibrium. Meter stick: xcm = 50.0 cm, m = 150.0 g. Hanger clamp: x = +0.0 cm, m = 16.5 g. (see the figure below)