Revisit Example 6 from your Module 4 notes. Consider the well-insulated, rigid tank having a volume of 10 [ft']. Previously, it contained saturated water vapor at 212°F at state 1. The water was rapidly stirred until the pressure was 20 [Ibfin'j. In class we showed that the temperature at state 2 was 445°F and the work done during this process was -31.3 [Btu]. Now, if insulation were removed from the tank, and the water is cooled at constant volume from T: = 445°F to T3= 300°F without stirring the water, determine: a) The pressure at the state 3 in (Ibfin), and b) The heat transfer during the process in [Btu].

Revisit Example 6 from your Module 4 notes. Consider the well-insulated, rigid tank having a volume of 10 [ft']. Previously, it contained saturated water vapor at 212°F at state 1. The water was rapidly stirred until the pressure was 20 [Ibfin'j. In class we showed that the temperature at state 2 was 445°F and the work done during this process was -31.3 [Btu]. Now, if insulation were removed from the tank, and the water is cooled at constant volume from T: = 445°F to T3= 300°F without stirring the water, determine: a) The pressure at the state 3 in (Ibfin), and b) The heat transfer during the process in [Btu].

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are working with an imagined cubical pot of water, 1 meter on each side, sitting on a stove. Heat is applied to the bottom of the pot from the stovetop. The pot has been on the stove for a while, so the stovetop is hot and some heat has already been added to the water. Assume the water at the bottom of the pot is held at 99 degrees C , while the water at the top of the pot is cold, 4 degrees C. Compute the heat delivered by that 1 g of water at 99 °C into the layer of water at the top of the pot, assuming the latter is 1 meter square, 1 cm deep, and 4 °C. Start by solving the calorimetry problem (Section 14-4 in the text) to determine the final temperature of the top layer plus hot 1 gram from below. Then use that to determine how much heat was delivered in the hot water
The previous solution makes no sense. Please provide correct handwritten solution. [The answer must he in handwritten format only , Please consider it]
In thermodynamic, a rigid tank may require you to deal with liqud or gas or both in the entire volume of the tank. Let’s say you need to create a container to keep one third of the volume inthe liquid phase in the form of steam water and the rest is in vapor, what are the parameters thatyou need to consider? Use relevant illustration of your design and prove it through yourcalculation.
2.5.18. [Level 2] You're out paddling a raft Rin the mid- dle of the river and hear a friend (located at F) call from the shore. In what direction should you paddle to arrive at F in 2 minutes? The river's current has a velocity li m/s. 48 m 48 m mont n lo odrio
Give the phase for the following states a. CO₂ at T = 40 [°C] and P = 0.5 MPa b. H₂O at T= 260 [°C] and P = 5 MPa c. Air at T = 20 [°C] and P = 200 kPa d. NH3 at T 170 [°C] and P = 600 kPa R-410A at T = 0 [°C] and P = 350 kPa e.
please show work and formulas so that i may learn the process correctly. if you use a table please mention which table was used. thank you so much. 2. Fill in the blank cells of this table: T( C) P(kPa) u(kJ/kg) Phase description 175 2524.5 325 4000 325 Saturated liquid
An ideal gas with a mass of 2 kg is reversible and polytropically a piston-cylinder in its assembly, it expands up to 3 times its first volume. If the temperature of the Ideal gas is 300°C it falls from a temperature of 60°C. (a) if the heat energy input is 20 kJ and the limit work output is 100 kJ, CV [kJ/kgK], which are specific gas temperatures] and find cp [kJ/kgK] values (b) if the thermal energy output is 20 kJ and the boundary work output is 100 kJ, CV [kJ/kgK] which are specific gas temperatures] and calculate cp [kJ/kgK] values (c) find the value k, which is the ratio of specific temperatures (d) if the thermal energy input is 20 kJ, the boundary work output is 100 kJ, and the entropy production is 0.36 kJ/K, the thermal energy calculate the source temperature as [°C].
Answer this. Upvote guaranteed! looking at the cylinder of your automobileengine and it has a volume of 524 cm3. By means of curiosity, you imagined that (a) if the cylinder is full of air at 74 °C, you questioned how much O2 are present in the cylinder (Note that the mole fraction of O2in dry air is around 0.2095). (b) You asked your classmate to help you in determining the number of C8H18that could be combusted by O2, assume that the combustion lead to the complete formation of CO2 andH2O. What would be the answer that you formulated?
In order to fnd the specifc heat c of an unknown substance, you place 75 g of the substance in a 30 g copper calorimeter that contains 65 g of water, all initially at 20 °C. You then add 100 g of water at 80 °C, and measure the fnal temperature of the system to be 49 °C. Assuming no heat is lost to the environment, what is c? [Answer: c = 2200 J/kg. K] 즈
What are the volumes of two chambers seperated by a piston wall that allows heat exchange but the system as a whole is isolated? The wall is initially fixed but then is loosed to move. How do you find the volumes of both chambers once equilibrium is reached? Each chamber is filled with a different, single-atom gas. I am given an initial mol, temperature, and pressure of each chamber.
An ideal gas with a mass of 2 kg reversibly and polytropically expands up to 3 times its initial volume in a piston-cylinder assembly. The temperature of the ideal gas drops from 300 ° C to 60 ° C. a) The heat energy input is 20 kJ and the boundary work output is 100 kJ. Find the specific heats cv [kJ / kgK] and cp [kJ / kgK] for the gas. b) If the heat energy output is 20 kJ and the boundary work output is 100 kJ, calculate the specific heats of the gas cv [kJ / kgK] and cp [kJ / kgK]. c) Find the value k, which is the ratio of specific heats. d) If the heat energy input is 20 kJ, the boundary work output is 100 kJ and the entropy generation is 0.36 kJ / K, calculate the thermal energy source temperature as [° C].
Engine Cycle: Our inventor is still trying to design a heat engine that will outperform the Carnot cycle .. Design #801-456 is for an ideal, reversible engine that operates with the cycle shown below (A → B → C → D → A). The engine contains 0.421mol of a gas that has a heat capacity ratio of y = 1.300. Point Pressure [N/m²] Volume [m³] Temperature [K] A 1.05 x 105 0.010 300 B 1.85 x 105 0.010 529 1.85 x 105 0.014 751 D 1.05 x 105 0.014 426 PA B A D V (a) What is the efficiency of this engine cycle? (b) What is the efficiency for a Carnot cycle working between the same maximum and minimum temperatures?