Rod BC in Fig. Q1 is made of A-36 steel and has a diameter of 15 mm. The modulus of elasticity and the shear modulus of rod BC are given as E = 200 GPa and G = 75 GPa. a) If the tensile yield strength of the rod is 250 MPa, prove that the rod is linear elastic. b) Determine the elastic elongation of rod BC and the contraction in its diameter. 6 kN E 3 m 1 m D 3 m C A 3 m Fig. Q1

Rod BC in Fig. Q1 is made of A-36 steel and has a diameter of 15 mm. The modulus of elasticity and the shear modulus of rod BC are given as E = 200 GPa and G = 75 GPa. a) If the tensile yield strength of the rod is 250 MPa, prove that the rod is linear elastic. b) Determine the elastic elongation of rod BC and the contraction in its diameter. 6 kN E 3 m 1 m D 3 m C A 3 m Fig. Q1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2 :A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm * 15.9 mm (3/16 in. 5/8 in.) is deformed in tension. Using the load-elongation data tabulated below, complete problems (a) through (f). Load Length Ib in. 75.000 2.953 2.954 4,740 1,065 2,055 2,900 3,720 75.025 9,140 75.050 2.955 12,920 75.075 2.956 16,540 75.113 2.957 18,300 75.150 4.110 4,530 5,145 2.959 20,170 75.225 2.962 22,900 75.375 2.968 25,070 5,635 75.525 2.973 26,800 6,025 75.750 2.982 28,640 30,240 31,100 76.500 78.000 79.500 6,440 3.012 3.071 6,800 7,000 7,030 6,930 3.130 31,280 81.000 3.189 30,820 82.500 3.248 84.000 3.307 29,180 27,190 6,560 6,110 85.500 87.000 88.725 Freeture 3.366 3.425 5,430 4,265 24,140 18,970 3.493 a) Plot the data as engineering stress versus engineering strain. b) Compute the modulus of elasticity. c) Determine the yield strength at a strain offset of 0.002. d) Determine the tensile strength of this alloy. e) Compute the modulus of resilience. f) What is…
1. The stress-strain diagram for a bar of steel alloy is shown. Determine: a) The modulus of Elasticity for the material b) The proportional limit c) The ultimate stress d) The modulus of resilience e) If the bar has a circular cross section with an initial diameter of 10-mm and is loaded to 260-Mpa, what will be the decrease in diameter under this load? Use v= 0.25 (MPa) Show complete solution.
Q2. Determine the young's modulus of elasticity from the following test result on a steel rod: Rod diameter = 25 mm Rod length Maximum applied load = 300kN = 150mm Rod extension after test = 10mm
20 KN . 38 mm Ø 1.0 m 40 KN 40 KN B 64 mm Ø1 1.5 m C Fig.pl-01 P2. Solve Problem P1-01 if rod BC is a hollow rod whose inner diameter is 38 mm. All' other data remain the same. 4 m
A stepped circular bar having diameter 20 mm, 15 mm and 10 mm over axial lengths of 100 mm, 80 mm and 60 mm, respectively, is subjected to an axial tensile force of 5 kN.If E = 100×103 N/mm2and Poisson’s ratio v = 1/m = 0.32 for the material of the bar, determine a) Total change in length.b) Change in each diameter.
The data illustrated below have been determined while the tension test of the stainless steel sample by amateur engineers. The gage length of the stainless steel sample was 50.8 mm (2.0in.) and, the original diameter of the steel sample was 12.8 mm (0.505in.). Load (Ib) Elongation (in.) Load (Ib) Elongation (in.) 14000 0.020 2 310 0.0022 14400 0.025 4 640 0.0044 14 500 0.060 6950 0.0066 14600 0.080 9 290 0.0088 14800 0.100 11 600 0.0110 14 600 0.120 13000 0.0150 13600 Fracture With the help of Excel, plot the stress-strain diagram for this test conducted, and define the following mechanical properties: a) Young modulus; b) Proportional limit; c) Yield stress @0.2% offset; d) ultimate stress; e) nominal rupture stress.
Find the force pneed to fill the gap. Young's modulus as 300 GPa C 1,5 cm² 2 cm2 P. A 1 cm 1/2 p 0.5 m 0.5 m 1 m 0.5 mm (a) 13.84KN. (b) 14.21KN.
2-8 The stress-strain data from a tensile test on a cast-iron specimen are Engineering stress, MPa 35 70 112 133 182 224 280 332 343 378 5.0 Engineering strain, e • 10 mm/mm 0.20 0.44 0.80 1.0 1.5 2.0 2.8 3.4 4.0 Plot the stress-strain locus and find the 0.1 percent offset yield strength, and the tangent mod- ulus of elasticity at zero stress and at 140 MPa.
F
A circular pipe of internal diameter 30 mm and thickness 4 mm is subjected to a force 30 kN and the elongation was measured as 1 mm. If the length of the pipe is 2 m, find the value of Young's modulus of elasticity and the stress in the pipe. Match each item to a choice: Young's Modulus (GPa) Stress (MPa): Choices: : 140.4 # 47.9 B 56.4 # 120.8 #240.8 8 70.2
Q1: Considering the forces acting on the bar having solid circular cross-section, and an elastic modulus of E=200 GPa ; 50 mm 20 mm 15 kN 20 kN 30 mm 12 kN a) Draw the normal force diagram of the whole bar and obtain the normal stress at each section of the bar. A B C 0.5 m 0.3 m 0.4 m b) Calculate the elongation of point A with respect to point C c) If the factor of safety of the system is foreseen as 1.75, calculate the minimum yield stress of the bar material (-
a. Plot the stress strain diagram b. Find the modulus of elasticity, ultimate stress and fracture stress and explain each term. Define modulus of toughness and find the same for the above specimen. Load (kN) Elongation (mm) 11.1 31.9 0.0175 0.0600 37.8 0.1020 40.9 0.1650 43.6 53.4 62.3 64.5 0.2490 1.0160 3.0480 6.3500