rotating at a constant speed. The angle of twist between A and D is limited to 1.50 degree. Use maximum shear = 60 MPa and modulus of rigidity 77 GPa. Solve its torque for each shaft AB and BC. And determine the diameter of the Shaft based on strength. The electric motor exerts a torque of 800 N- m on the steel shaft ABCD when it is 3000 N.m 500 N.m B 0.4 m 0,6 m 0,3 m

rotating at a constant speed. The angle of twist between A and D is limited to 1.50 degree. Use maximum shear = 60 MPa and modulus of rigidity 77 GPa. Solve its torque for each shaft AB and BC. And determine the diameter of the Shaft based on strength. The electric motor exerts a torque of 800 N- m on the steel shaft ABCD when it is 3000 N.m 500 N.m B 0.4 m 0,6 m 0,3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel shaft 2542 mm long must transmit a torque of 34 KN-m. The total angle of twist and the maximum shearing stress must not exceed 3 degree and 110 MPa respectively. Find the diameter of the shaft that meets there conditions. Check based on strength and rigidity. Use G = 78268 MPa. Use two (2) decimal places.
A solid shaft consisting of steel and aluminum segments carries the torques T and 2T. Find the largest allowable value of T if the working shear stress is 14,000 psi for steel and 7,500 psi for aluminum, and the angle of rotation at the free end must not exceed 8 degrees. Use G = 12 x 10^6 psi for steel and G =4 x 10^6 psi for aluminum. Express your final answer in Ib.ft to the nearest whole number. Note: Do not include the unit in your answer. 27 2 in. 1.5 in. 3 ft B 2 ft |C 800mm 500mm
A solid shaft has an allowable shear stress of 37 MPa and transmits a torque of 1236 Nm. Determine the minimum diameter of the shaft in mm (give answer correct to 2 decimal places).
an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of twist must not go over 3 1/2 degrees in the 6ft. pick the economical shaft size.
A steel shaft 2573 mm long must transmit a torque of 34 KN-m. The total angle of twist and the maximum shearing stress must not exceed 3 degree and 110 MPa respectively. Find the diameter of the shaft that meets there conditions. Check based on strength and rigidity. Use G = 78268 MPa. Use two (2) decimal places. Add your answer
A shaft made from acrylic is subjected to the three torques indicated below. The acrylic has a shear modulus of 1.7 GPa. Determine: a. The twist at the end D if the diameter if the shaft is 100 mm. b. The minimum shaft diameter if Tallow = 10 MPa 200 N•m A 800 N•m 300 mm B 400 N•m 600 mm C 600 mm
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T (in Nm) that can be applied to the ends of the shaft without exceeding a shear stress of 70081031 Pa and angle of twist of 2.31°. Use G= 83000000000 Pafor the shaft, x = 2.5 m, and y = 1.71 m. Round off the final answer to two decimal places. T ... 100 mm 70 mm 70 mm T y
If allowable shear stress in the shaft is 8ON/mm² and the torque equivalent(Te) is 1.23 x106 N-mm. Find the diameter of the shaft. а. 45.78 mm O b. 68.78 mm 42.78 mm O d. 50.78 mm
A shaft required to transmit 50kW of power will be running at 100rev/min. The maximum twist in 3m length of the shaft is limited to 1.5 degree. If the maximum torque is 30 percent more than mean or average torque. Assume entirely elastic action and take modulus of rigidity for the shaft material G = 135 GN/?2. Determine the following:a. Diameter of the shaft.b. Maximum shear stress developed in the shaft. I need answer ASAP. Thank you!
Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 kN.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst 115 GPa, Gbr 56 GPa. 3 m %3D 2 m 100 mm 50 mm T= 50 kN. m
Determine the allowable torque a hollow steel shaft can transmit if the outside diameter is 4 inches, and the inside diameter is 3 inches. The allowable shear stress is 10,000 psi. Compute the angle of twist per foot of length. Answer = 85,900 in-lbs I'm unsure of how to solve this problem. Could you please help me solve for the answer step-by-step? Thank you in advance.
What is the minimum diameter of a solid steel shaft that will not twist through more than 3.18 degrees in a 6 m length when subjected to a torque of 14KN-m. What maximum shearing stress is developed? Use G=83GN/m^2.