SAE 30W oil at 20°C flows through a 9-cm-diameter pipe as shown in the diagram at an average velocity of 4.3 m/s. For . SAE 30W oil, p= 891 kg/m andp = 0.29 kg/(m-s). D =9 cm SAE 30W oil Hg 2.5 m Calculate the expected reading h of the mercury manometer in m. The density of oil and mercury is 891 kg/m and 13550 kg/m3 respectively. m. The expected reading h of the mercury manometer is

SAE 30W oil at 20°C flows through a 9-cm-diameter pipe as shown in the diagram at an average velocity of 4.3 m/s. For . SAE 30W oil, p= 891 kg/m andp = 0.29 kg/(m-s). D =9 cm SAE 30W oil Hg 2.5 m Calculate the expected reading h of the mercury manometer in m. The density of oil and mercury is 891 kg/m and 13550 kg/m3 respectively. m. The expected reading h of the mercury manometer is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem (3) Find the rate of change of h(t) (mm/s) if water is the fluid at all locations. Use V₁ = 7.1 m/s and Q = 1000 L/min. m₂ = 10 kg/s 4 cm dia. V₁ Answer: 120 cm h(t) 8
An incompressible fluid (kinematic viscosity, 7.4 x10-7 m²/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is rt of this book may be repro
The velocity distribution in a 0.02 m diameter horizontal pipe conveying carbon tetrachloride (specific gravity = 1.59, absolute viscosity = 9.6 x 10-6 Pa sec) is given by the parabolic equation: v(r)=0.01(0.12- r?), where v(r) is the velocity in (m/s) at a distance r in (m) from the pipe center. What is discharge? O a. 3.13 x-8 m3/s O b. None of the mentioned O c. 1.047 x 108 m3/sec O d. 4.97 x 109 m3/sec
An incompressible fluid (kinematic viscosity, 7.4 x10-7 m²/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is (a) 0.651 x 10-3 (c) 6.51 (b) 0.651 (d) 0.651 x 103
338 B/s O 1: 56% E 3:01 Question: Gasoline is flowing through this 180° pipe bend. The pipe cross-sectional area is 18 in?. Take the pipe weight as 5 Kg. Flow rate is 0.5 liters/s. Pressure at section-1 6 psia, pressure at section-2 is 4 psia. Calculate the anchoring force required to hold this pipe and also show its direction, referenced to proper 2-dimensional a cartesian coordinate system. (2 1
A pressurized tank of water is used to create a fountain, as illustrated. Assume that the water's free surface area in the tank is very large relative to the pipe's cross-sectional area, which is circu- lar with diameter d 1.0 cm. The small pipe bend has height = 10.0 cm. At the instant when 0.75 m, H = 2.5 m, and the gauge measures a pressure of Pgauge 20.0 kPa, the water spray reaches a height L above the pipe exit. h = = = Neglecting viscous effects, determine the height of the spray, L.
QA An incompressible fluid (kinematic viscosity, 7.4 x10-7 m2/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is (a) 0.651 x 10-3 (c) 6.51 (b) 0.651 (d) 0.651 x 103
SAE 30W oil at 20°C flows through a 9-cm-diameter pipe as shown in the diagram at an average velocity of 4.3 m/s. For SAE 30W oil, p = 891 kg/m3 and u = 0.29 kg/(m-s). D=9 cm V SAE 30W oil Hg 2.5 m Calculate the expected reading h of the mercury manometer in m. The density of oil and mercury is 891 kg/m and 13550 kg/m3 respectively. m. The expected reading h of the mercury manometer is of 17 Next> ( Prev 8.
Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 12 in. The atmospheric pressure is 14.7 Ibf/in?, the specific volume of water is 0.01604 ft/lb, and the acceleration of gravity is g = 32.0 ft/s?. Patm = 14.7 Ibr/in.? g = 32.0 ft/s² Water v = 0.01604 ft/lb Determine the difference in pressure between points a and b, in Ibf/in2?. Does the pressure increase or decrease from point a to point b? Sten 1
An incompressible fluid flows through a pipe without significant viscosity. It has a density of 124 kg per cubic meter. In a section of pipe with a 2.8 cm radius the fluid moves at a speed of 13 m/s, and has a pressure of 103,763 pascals. It flows into a section of pipe with a 3.87cm radius that is 5 meters higher than the first section. What the pressure in the second section of pascals?
FLUID FLOW Example 5: A liquid food with a density of 800 kg/m³ is being transported at a rate of 5 ton/h through the system shown below. If the pressure at point 1 is 20 kPa gage, determine the pressure at point 2. Neglect friction losses. Example 5 P₁ = 20 kPa D₁ = 0.08 m 6 m 2 FLUID FLOW P₂ = ? D₂ = 0.025 m
A pipe flowing water has a manometer attached, as shown in the figure. The local atmospheric pressure, Po, is 101.3 kPa and the gravitational acceleration is 9.81 m/s². The densities of the water (pw), oil (po«), and mercury (png) are 1000.0, 800.0 and 13,600 kg/m³, respectively. The heights of the liquid levels in the manometer system are indicated in the figure. What is the absolute pressure at the center of the water pipe, Pw, in kPa. oil Poil = 800.0 kg/m³ P. h, = 110 cm h, = 30 cm h, = 20 cm h, = 95 cm h water h water Pu= 1000.0 kg/m³ mercury PHe=13,600.0 kg/m³