Select a W section to serve as purlins between roof trusses spaced at 4.6 m on centers. Assume all loads passes through the Centroid of the purlins. Spacing of purlins is 1.4 m on centers. Assume that the purlins are fully laterally supported and subject to the following: Loads Snow = 1440 N/m2 of roof surface Roofing = 288 N/m2 of roof surface Wind surface = 720 N/m2 perpendicular to roof surface Slope of the roof truss is 1 vertical to 2 horizontal. Sag rods are provided at the midpoints of the truss. A36 steel, Fy=248 MPa Select from any W section listed in the table below. Use ASD

Select a W section to serve as purlins between roof trusses spaced at 4.6 m on centers. Assume all loads passes through the Centroid of the purlins. Spacing of purlins is 1.4 m on centers. Assume that the purlins are fully laterally supported and subject to the following: Loads Snow = 1440 N/m2 of roof surface Roofing = 288 N/m2 of roof surface Wind surface = 720 N/m2 perpendicular to roof surface Slope of the roof truss is 1 vertical to 2 horizontal. Sag rods are provided at the midpoints of the truss. A36 steel, Fy=248 MPa Select from any W section listed in the table below. Use ASD

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design the purlin between two trusses spaced 3m apart to support 0.19 KPa roofing. Spacing of purlins is 0.50m on centers. Allowable bending stress is 12.84 MPa, allowable shearing stress is 0.70 MPa and allowable deflection is L To 0.50m $ 3m b=? 2m d=?
ASSIGNMENT #6 CASE 2 Purlin Design The figure shown has trusses 5.5m apart with midpoint sag rods and Purlins spaced 2.5m on center. The roof truss is inclined 1 vertical to 2 horizontal. The weight of roofing materials is 0.8 kPa, wind load is 0.7 kPa perpendicular to the roof surface, minimum roof live load is 0.6 kPa. Design a channel section of steel Fy = 345 mPa, for the purlins. Use LRFD and ASD of NSCP 2015.
A Mansard roof truss is loaded as shown. Determine the force in members DF, DG, and EG. 3 m ✓ A 1.2 kN 1.2 kN 1.2 kN 1.2 kN 1.2 kN B D C E| k 2.25 m 4 m. F G 4 m- H -4 m I 4 K OL 2.25 m Show complete solutions and diagrams. Original work please I will upvote
Q 3 List down the assumptions made in deteriming the truss.
How many Zero force members are there in the truss shown? В D F E A K H[100 kN 60 kN LL 60 kN O 2 O 3 5 O 7
a) The short steel post as shown in Figure 4 is a 152 x 152 UC37 with three compressive loads applied to the top. There is a central load of 200KN and eccentric loads of 'W kN and 100kN. The maximum allowable stress on the face AB is 185 N/mm?. (Area=D47.1cm2,Zxx=273cm) What is the value of the load 'W in kN? WkN A. 152 x 152 UC37 100mm -200KN 50mm 100KN Not to scale Figure 4
Design a purlin for a roof truss having the following data:Span of the truss = 6.0mSpacing of truss = 3m c/c.Inclination of roof = 30oSpacing of Purlin = 2m c/cWind pressure = 1.5 kN/m2Roof coverage= A.C Sheeting weighing 200 N/m2Provide a channel section Purlin.
Problem 8.4 Distributed Loads The framing system shown in the figure is subjected to a 7.7 kN point load and triangular distributed load with a maximum magnitude of 9.5 kN/m. You are required to: a) Determine the reaction forces at the Pin D. b) Determine the reaction forces at Pin A. c) Determine the force in the member AC. 7.7 kN B 2.5 m STENDER EERSTE CONNECTION SEAN BUTER PLATING 3.5 m D INNER BOTTOM PLATING TRANSVERSE LONGITUDINAL STRAKE 9.5 kN/m 5 m
4) Determine the bar forces for the given truss. III 12 II3 9. 11 A 2. 10 13 F a a a 00
Determine the unity check ratio for the member GF of the truss shown below (Per API RP-2A code provisions). Joints of the truss are frictionless joints and the forces in the truss members are axial forces only. 20 kip Member GF (Hollow circular cross section): Outer diameter = 10" 30 kip 30 kip 30° Wall thickness = 0.25" Ey = 50 ksi 300 E 60° 60° 30° K=1.0 A, 30 60° 60° 30° 30 D. 4ft 4ft 4ft Ay [Hint: Axial Force in member GF = 50 kips (axial compression)]
10 mm | | | | 10 mm 50 mm ارت - 50 mm 10 mm 20 kN B 150 mm 910 mm 10 kN D ------- 150 mm Two vertical forces are applied to a am of the cross section sh vn. Determine the maximum tensile and compressive stresses in portion BC of the beam.Show your complete solution and box your answer.
Which joint would be the best place to start your analysis of the truss shown? D 8k 12 k O a. F O b. D O c. B O d.c E 15 ft- + 15 ft- B 24 k +15 ft- 2+15+ -15 ft- T 8 ft EL