Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?

Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
a) Demonstrate input and output waveform of single phase Cyclo-converter such that output frequency is 1/3 of input supply frequency with circuit diagram. b) Perform the calculation to analyze (i) output RMS voltage and (ii) input power factor of single-phase AC voltage controller as shown in the following figure. Suppose converter has a resistive load of R=‘A’ Ohm and the input voltage is Vs=220, 50Hz with a delay angle of π/3. A= 4
4.) A transformer has a primary coil with 300 windings, and secondary coil has 400 windings. The input AC power supply is 120 volts (Vrms). A) Is this a step-up or step-down transformer? B) What is the rms voltage across the output terminals (Vrms)? C) What is the peak voltage across the output terminals (Vmax)? Primary Secondary imm ac input
Difference between sc and oc test in transformer...
Determine the regulation of a transformer in which thepercentage resistance drop is 1% and the percentagereactance drop is 5% when the power factor 0.8 leading.
An RLC series circuit connected to a 110 – volt and 50 – cycle AC source, contains the following series resistances and reactances: R1 = 10 ohm, R2 = 15, R3 = 5 ohms, XL1 = 20 ohms, XL2 = 25 ohms, XC = 40 ohms. Find the following: a.) EQUIVALENT REACTANCE b.) TOTAL IMPEDANCE c.) VOLTAGE DROP ACROSS THE CAPACITOR d.) TOTAL INDUCTANCE IN MILLIHENRY e.) TOTAL CURRENT f.) REACTIVE POWER g.) REAL POWER DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES
Q2/ Fill in the blanks: 1- The two windings of a transformer is linked. ***** 2- If a transformer primary is energized from a square wave voltage source, its output voltage will be.......... 3- The primary winding of a 220/6 V, 50 Hz transformer is energized from 110 V, 60 Hz supply. The secondary output voltage will be ...... V.
A 50 Hz 1-phase transformer has a turn-ratio of 6. The resistances are 0.90 ohm and 0.03 ohm and the reactance’s 5 ohm and 0.13 Q for high voltage and low voltage respectively. Determine (a) the voltage to be applied to the high voltage side to obtain full load current of 200 A in the low voltage winding on short circuit (b) the p.f. on short circuit.
Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
7. The primary of a single-phase transformer takes 1 A at power factor of 0.4 when connected to a 240-V, 50-Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. What is now the value of the primary current ? transformer.) (Neglect the voltage drops in the
Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 Vrms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Use germanium diodes.