SITUATION: Sphere A is attached to Sphere B by a cable whose mass is negligible. Both spheres are identical in dimensions, R = 0.6 m, but differ in material composition. If sphere A has a mass of 1223.24 kilograms and sphere B has a mass of 407.747 kilograms and both !3! spheres are thrown in water (SG = 1.0), determine the following: %3D The exposed volume of the sphere B in cubic meters. 0.179 0.726 0.114 0.220

SITUATION: Sphere A is attached to Sphere B by a cable whose mass is negligible. Both spheres are identical in dimensions, R = 0.6 m, but differ in material composition. If sphere A has a mass of 1223.24 kilograms and sphere B has a mass of 407.747 kilograms and both !3! spheres are thrown in water (SG = 1.0), determine the following: %3D The exposed volume of the sphere B in cubic meters. 0.179 0.726 0.114 0.220

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Ex.1 Ans. A glass tube 0.25 mm in diameter contains a mercury column with water above the mercury. The temperature is 20°C at which the surface tension of mercury in contact with water is 0.037 kg()/m. What will be the capillary depression of the mercury? Take angle of contact 0= 130°. 3.02 cm
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E 200, 000M Pa and %3D a = 11.7- Neglect bending of the beam. A=640mm2 A=320mm2 A C 1.2 m 0.8 m 1.2 m V 54KN 1. If there is no change in temperature, what is the deformation of rod C in mm? 2. If there is no change in temperature, what is the deformation of rod B in mm? 3. What is the stress of rod C if there is no change in temperature in MPa? 4. What is the vertical displacement of D in mm, if the temperature rises 50°C? 5. If the temperature rises, what is the thermal deformation of steel in mm?
3. A cube, 60 cm on an edge, has its upper halfhaving a specific gravity of 0,60 and the lower half 1.40. It is placed in a two-layered liquid. Find the value of z liquid surface S, = 0.90 60 cm トー 30 сm S, = 0.60 30 cm S = 1.20 S = 1.40
A 150mm x 150mm square metal plate, 10mm thick, is hinged about a horizontal edge. If a 10mm diameter horizontal jet of water impinging 50mm below the hinge keeps the plate inclined at 30 degrees to the vertical, find the velocity of the jet. Take the specific weight of the metal as 75kN/m^3.
2.) A 1060kN cube (3m each side) floats in a 1.8m depth of water which is on top of mercury layer. a) Determine the vertical distance from the top of the cube to the interface of water and mercury. b) If a load of 760kN is added to the weight of the cube, what is the distance from the top of the cube to the water surface?
E. Find the depression h of the mercury in the glass capillary tube having diameter of 2mm if the surface tension is 0.514 N/m for 0 = 40°. 1. 2. Compute the force caused by surface tension. 3. Determine the density of mercury.
The surface tension of mercury at 60°C is 0.47N/m. What capillary height in mm will occur in this fluid whe in contact with a glass tube of radius 0.3mm? Use 130° for mercury. O 11.5mm fall O 11.5mm rise O 15.1mm fall O 15.1mm rise
3. A brass sphere (sp.gr. 8.60) is placed in a body of mercury. If the diameter of the sphere is 30cm. a. What minimum force would be required to hold it submerged in mercury? b. What is the depth of floatation of the sphere when it is floating freely?
4. The capillary rise when a glass capillary tube of diameter 0.4mm is dipped vertically in olive oil is 3.8mm. If the angle of contact of olive oil with glass is 0 deg and the density of olive oil is 920 kg/cu.m, find the surface tension of olive oil. 5. A liquid rises to a height of 9cm in a glass capillary of radius 0.02 cm. What will be the height of the liquid column in a similar glass capillary of radius 0.03 cm?
28/2/202) 2 = Semester 1 Exar Students' classes = docs.google.com a 25.544 mm 21.014 mm Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m. 1 m Liquid (s.g. = 0.88) 3.8 m 1 m
For the thin-walled tube shown, the polar moment of inertia is about * .21714.6 mm^4 2mm 12mm True O False
Calculate the velocity of a 1.5 ft x 3 ft flat plate that is pulled through a t= 0.04 inch thick layer of kerosene with a force, F = 3 lb. 13.2 ft/s 27.7 ft/s O 10.4 ft/s O 17.6 ft/s 35.2 ft/s O2.69 ft/s