The soccer ball shown weighs 1 lb and has a velocity of 20 fps at 40° to the horizontal prior to striking the soccer player's head. After the soccer player heads the ball, it has a velocity of 30 fps at 20° to the horizontal. If the duration of the impact is 0.15 sec, determine a. Express the initial and final velocities of the ball in Cartesian vector form b. Magnitude and direction of the average force exerted on the soccer ball by the player's head in Cartesian vector form.

The soccer ball shown weighs 1 lb and has a velocity of 20 fps at 40° to the horizontal prior to striking the soccer player's head. After the soccer player heads the ball, it has a velocity of 30 fps at 20° to the horizontal. If the duration of the impact is 0.15 sec, determine a. Express the initial and final velocities of the ball in Cartesian vector form b. Magnitude and direction of the average force exerted on the soccer ball by the player's head in Cartesian vector form.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The ballistic pendulum is a simple device to measure projectile velocity v by observing the maximum angle e to which the box of sand with embedded projectile swings. Calculate the angle e if the 2.7-oz projectile is fired horizontally into the suspended 59-lb box of sand with a velocity v = 2150 ft/sec. Also find the percentage n of energy lost during impact. le 4.4' Answers: e = i n =
2/13 In the final stages of a moon landing, the lunar mod- ule descends under retrothrust of its descent engine to within h = 5 m of the lunar surface where it has a downward velocity of 2 m/s. If the descent engine is cut off abruptly at this point, compute the impact velocity of the landing gear with the moon. Lunar gravity is of the earth's gravity. h Ans. v = 4.51 m/s
* 5. In preliminary design studies for a sun- powered car, it is estimated that the mass of the car and driver will be m kg and the torque produced by the engine will result in a F, newton tangential force on the car. Suppose that the car starts from rest on the track at A and is subjected to a constant Ft newton tangential force. Determine the magnitude of the car's velocity and the normal component of R m END B A START l m Figure 5. force on the car when it reaches B. m = .15.. kg Fe .newton .m R = 31.25
For what value(s) of the angle 0 will the acceleration of the 35-kg block be 9 m/s? to the right? 1. P = 450 N 35 kg Hg = 0.6, k = 0.5 %3D
In the figure, the 50-N ball and 40-N ball, moving as indicated meet in oblique impact. If e=0.6, . Assume the surfaces of the balls are smooth. a. determine the amount and direction of the resultant velocity of 50-N ball after impact b.determine the amount and direction of the resultant velocity of 40-N ball after impact
Your answer is partially correct. The 1.62-oz golf ball is struck by the five-iron and acquires the velocity shown in a time period of 0.0018 sec. Determine the magnitude Rof the average force exerted by the club on the ball. What acceleration magnitude a (measured in "g"s) does this force cause, and what is the distance d over which the launch velocity is achieved, assuming constant acceleration? v = 142 ft/sec 23 Answers: R = 248.05 Ib a = i 78886.02 d = 1.5336 in.
The 1500-lb cannon shown fires an 12-lb projectile with a muzzle velocity of 1200 ft/sec measured relative to the cannon. determine the recoil velocity of the canon and the velocity of the projectile just after firing Recoil spring
Q4 2. A ball is launched with an initial velocity of Vo = 4.5 m/s from point P at a 30° sloped surface with an angle of 0. The ball lands at point B, which is 0.6 m higher than point A. Determine the launch angle 0 of the ball, the impact velocity at B (vB), the angle vg makes with the horizontal and the duration of the flight. Also determine the radius of curvature of the path and the rate of change of the speed of the ball at point C, where its trajectory makes an angle of 60° with the negative x-axis. g 9.81 m/s-.
: The 3-lb collar is released from rest at A and slides freely up the inclined rod, striking the stop at B with a velocity v. The spring of stiffness k 1.8 lb/ft has an unstretched length of 15 in. Calculate the kinetic energy = and v. Note: Use the equation of principle of work and kinetic energy in solution. BAB k= 1.60 lb/ft 18" wwwwww 20" 10"
The door is made in one piece, the ends of which move along the horizontal guides and vertical. If the door is in the open position, θ = 0◦ , and then released, determine the speed (this is already solved Vinpact = 31.9 ft / s) at the that its outer A hits the stop C. Suppose the door is a 180-lb thin plate that has a width of 10 ft. Determine the impulsive force with which point A hits point C in an instant of 5 thousandths of a second.
Guammen'S Not yet intered Marked out of The slender bar of mass med 22 kg is moving to the right on frictionless rollers at A and B with the velocity V, when the roller at B strikes the small obstruction C without rebounding, Compute the minimum value of V, for which the bar will reach the vertical position after the impact. y V1 Select one: ĐA Vị 7352 m/s OB V₁ = 5.824 m/s OC V₁.0 m/s OD. V = 1.527 m/s L = 3 m 40° B X C
A motorcycle and rider have a combined mass of 350kg. The vehicle's velocity is 100 km/hr. The rider is to go up a hill incline of 10 meters. The wheels each have a mass of 20 kg and a diameter of 500mm. The wheel design consists of 6 spokes with a mass of 0.5 kg for each spoke. a. Determine the vehicle's velocity at the top of the hill, assuming it was a rolling vehicle with engine being turned off. a. Indicate the vehicle's velocity at each meter through the climb. b. Explain the transfer energy and how this affects the behaviour of the system. At another point in its journey, the motorcycle and rider travel at 80 km/h around a left-hand bend of radius 30m. Calculate: a) The angular velocity of each wheel. b) The moment of inertia of each wheel. c) The angular momentum of the wheel prior to entering the bend. d) The magnitude of the gyroscopic torque produced on the bike as the rider is driving around the bend. What is the effect and why is it important to calculate the gyroscopic…