Solve for the tensions 45 50 g

Q: Solve for V, (m/s).

A:

Q: 400 16/in to N/m

A: To convert 400 lb/in to N/m

Q: 4 5/8" as meters

A: Given-4 5/8" or 4 5/8 inch To find-change the length into meter

Q: taper angle and the set over respectively are

A: Given data,  Length of the shaft,L= 90 mm Tapered portion length,TL=55 mmD=80 mmd= 65 mm Determine…

Q: Compute (I bar sub x, in mm4, round-off to 2 decimal places) for the region shown. X

A:

Q: A thin-walled tube is subjected to torsion as shown. Determine the angle of twist produced. (in rad)

A: Given Radius =300 mm = 0.3 m Length = 6 m Thickness = 25 mm = 0.025 m T = 4kN m = 4000 Nm G = 70 GPa…

Q: . Find the width c will

A: Need to find width of rectangular duct.

Q: Solve for Ix, Ix, Iy, and Iy. 20mm Ix for circle: T*/4 Ix for sem-circle: (-)-4 Ix for quarter…

A: Consider the section as shown below,

Q: Solve for the mobility.

A:

Q: intil its volume bec e work done by the elow, show the can ston and draw a fre

A: GIVEN:v1=14.5lv2=130.5lP=1720KN/m2

Q: Calculate the y-component of D (in N, round-off to 2 decimal places) of the loaded frame. D 600 N…

A:

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: the shear force right of C is

A:

Q: 5. Find the approximate shear stress

A: To find approximate shear stress developed Exact shear stress developed deformation of the spring

Q: Express the quantity 556.2 x 10^-12s in ps.

A: Given: The time in second is t=556.2×10-12 The unit conversion factor converts Second into…

Q: For the H- section shown, Find the value of h so that I = ly. 20mm 100mm | 20mm h = ? 20mm 140mm

A: Draw the given H-section. Since the given H-section is symmetric, the centroid will lie in the…

Q: Solve 0.782bar in p/q form

A: Given that : x = 0.782782782....... We need to find it in the form of p/q

Q: Determine P and RA

A:

Q: In the truss shown, find the value of 21 in degrees.

A:

Q: ction shown Assu

A: Given:  T = 4730 KNm τ = 125MPat = 10mm

Q: 1 6 A В

A: Given data: The current flowing is given as I = 6A. Since OA = OB, The opposite sides of equal and…

Q: Q3. Answer the following A) Resolve the 500-lb of fig. into two components: a shearing component…

A: Data given - Force of 500lb at angle of (90-theta) To determine - Resolve the forces parallel to AB…

Q: 3.

A: Degree of Freedom (mobility): The minimum number of independent variables required to define the…

Q: Solve for the stress of a plate (in Pascals) in order to punch a hole 20mm diameter that is 25mm…

A: Given data: d=20 mmt=25 mmF=550 kN Need to determine the stress (shear stress) in the plate.

Q: work output from the

A: Given; An engine operates on the reversible cycles as shown in the figure.Find work output from the…

Q: Find (Ix&ly), if a=30mm. a

A:

Q: 4. The block had to go up to the circular arc as shown, starting from velocity of 17 m/s at the…

A:

Q: Sind y at 2 m from the left hand 7111 سحله ولي dx

A: Concept: The integration of the load intensity is the shear force. The integration of the shear…

Q: Solve For the muximum value OF that pre vents the bar AP 50 kN. From moving if it weighs B P Am

A:

Q: Express the quantity 30.6×10^−4m in mm

A:

Q: Find the Diameter of the shaft

A:

Q: Solve for Fv

A: To find Fv

Q: DISSO a) Determine the decrease in its length b) Determine its new diameter.

A: for solution refer below images.

Q: Solve for the areain two different ways. 12

A:

Q: Determine C/R for the

A: To determine C/R using block diagram Verify the result using signal flow graph. Topic : Control…

Q: r to the simply sup m shown. What is n lv the maximum be

A:

Q: The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa…

A:

Q: Determine the flange thickness if the

A: To find Flange thickness

Q: iven: P = 8 kips Determine the shearing stress just below point a. (Round the fi

A: P=8kips

Q: Find the tensian focce in each cable.

A:

Q: Please solve for 4.139  thx

A: Free body diagram of the problem To find The tension in the string Fdf

Q: Find the allowable maximum value of F.

A: we have to evaluate the maximum bending stress

Q: For the following Internal clovetails if b is yomm grater than C. M is 60 mm 25 mm less Find the…

A:

Q: rad/sec and having 20 te sure angle is 20° and m. on at the centre of the sha

A:

Q: 5.

A:

Q: 2. If 75 N/mm is the maximum shear stress and 50 kN-m is the torque acting on a solid shaft, then…

A: Given: Maximum shear stress τmax = 75 N/mm2 = 75000 kN/m2 Torque acting on a shaft      T = 50kN-m…

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.