Steel railroad reels 10 m long are laid with a clearance of 3 mm at a temperature of 15°C. At what temperature will the rails just touch? What stress would be induced in the rails at that temperature if there were no initial clearance? Assume a = 11.7 µm/(m-°C) and F = 200 GPa
Q: A thin-walled cylindrical pressure vessel of radius r is subjected simultaneously to internal gas…
A: Given data F=190 kNP=12 MPad=200 mm Here, F is the force, P is the pressure and d is the inner…
Q: A dimensionless group on which its application is on pressure and momentum in fluid
A:
Q: In an experimental procedure to determine stress, the radial displacement u at a known radius, is…
A:
Q: Which among the statement is correct? (A) Major losses are the head losses that occur due to bends,…
A:
Q: Which among the statement is correct? A Frictional loss is that part of the total head loss that…
A:
Q: Q2: Fig.(2), represents a simplified diagram of a spring-supported vehicle traveling over a rough…
A: as per rule, i solved 1st question only
Q: Given that the length of a work-piece made from copper alloy to be face-milled is 250 mm and the…
A: Given : L = 250 mm D = 150 mm z = 10 To find : Cutting speed and feed
Q: place the three forces shown by an equivalent force-couple system at point A. If the forces are…
A: Solution - Now we finding the three forces shiwn by an equivalent force couple system at point A.
Q: A particle has a diameter of 0.20 millimeters (Spec.grav = 2.5) falling in a liquid (Spec.grav =…
A:
Q: A C B D
A: GIVEN DATA ORTHOGRAPHIC PROJECTION GIVEN WE HAVE TO CHOOSE CORRECT ISOMETRIC PROJECTION
Q: Replace the two forces in Figure (2) with a single force at the point (A) and double tension (B)…
A:
Q: A pulley with an inertia J has a weight with a mass m hanging on it at a radius R, from the pin. A…
A: Given : To find : Equation of motion
Q: A screw jack mechanism is to be incorporated into the machine as part of a levelling system. The…
A: Given data as per the question Diametre of jack =45 mm Thread pitch =6 mm coefficient of friction…
Q: s height is 2.5-m. Solve fo s only up to 120 MPa, wh
A:
Q: / Act on the structure in Figure 4 horizontal force NK Finally, D. Find the effect of the reaction…
A:
Q: the following: - Reaction support at point B. - Reaction support at point D. - Centroid of the…
A:
Q: What is the mechanical advantage of a 1/4" diameter screw with 20 threads per inch?
A: Calculating the mechanical advantage of a 1/4" diameter screw with 20 threads per inch.
Q: 22: Moment of Q? 500 lb 700 Kg*m/s² O 10 m 300 Kg
A:
Q: 2. Carbon steel shaft with diameter of 350 mm is heat treated in a gas fired furnace where the gas…
A: Given:d=350 mmT∞=2000 Kh=25 W/m2.KTb=500 KC=600 J/Kg.Kρ=7800 Kg/m3
Q: Compute the moment (positive if counterclockwise, negative if clockwise) of the 0.32-lb force about…
A:
Q: just answer number 40, thank you
A:
Q: A cylindrical cold storage facility with an inner diameter of 4m and height of 2m is constructed.…
A:
Q: Make and draw the shear and moment diagram for the beams shown below. You can give or assign the…
A:
Q: 8. What force P must be applied to the weightless wedges shown in the figure to start them under the…
A:
Q: What is the minimum pipe diameter in cm that can be recommended if the flow is 5 m^3/s and the…
A:
Q: A 4.5 m diameter diesel tank has an outlet nozzle of 75 mm in diameter. What is the mass flow rate…
A:
Q: N₂ vapor Tair The boiling temp of nitrogen at 1 atm is -196°C. If the temperature of liquid nitrogen…
A: The thermal resistance of a material is determined by dividing its thickness by its thermal…
Q: In electroplating, the material to be plated, such as a necklace, acts as the cathode. Select one:…
A: Correct answer: True
Q: At an amusement park in the greater area there are three 180-kg bumper cars occupied by seniors. The…
A: Given: Assume that each car and its rider can be considered a particle. Let's write the given as…
Q: A water storage tank contains water whose level is 18 meters above the bottom of the tank. A…
A: Given: h = 18 m Pgauge = 206 kPa
Q: Q3:A/ Find the solution to the following linear programming problem by dual simplex method Min Z=…
A:
Q: 2. Carbon steel shaft with diameter of 350 mm is heat treated in a gas fired furnace where the gas…
A: The given values are - Diameter(d) =350 mm , Surrounding temperature(T∞) = 2000K, Initial…
Q: es in Figure (1) with a single force at point A and a double acting B has forces at points A
A: The force system can be shifted by point load and a moment as below
Q: 5 wt% Fe-5.5 wt% C at a and types of The Phases t Of Phases Present in Gr Microstructure Of Phases
A:
Q: Air enters the compressor of an ideal air-standard Brayton cycle at 158 kPa, 340 K, with a…
A:
Q: Replace the two forces in Figure (2) with a single force at the point (A) and double tension (B)…
A:
Q: below- ning Parameters Speed te Cut Symbol Vc f d Unit m/min mm/rev mm -1 200 0.1 1 Leve 0 250 0.13…
A: Number of process parameters =3 Number of level for each process parameters= 3 The design matrix for…
Q: A 3000 pound force is applied to a piston causes a pressure of 800 psi. What is the diameter of the…
A: Given - Force(F)=3000 pound force = 13344.66 NewtonPressure(P) = 800 psi = 5515810 kPa Let d be the…
Q: Q2: The horizontal force NK 5 at the end D is acting on the structure in Figure (2). Find the effect…
A:
Q: 1. A pipe is covered with three insulation layers 250mm and 300mm and the respective thermal…
A:
Q: Explain shortly what you know about the following terms as applied in heat treatment.…
A:
Q: Consider a steam power plant that operates on an ideal reheat- regenerative Rankine cycle with one…
A:
Q: 52. Determine the possible indexing required (a) to produced a nonagon (9 sides) cross-
A: we have to determine what indexing to us to make a nonagon
Q: The cross-sectional dimensions of a beam are shown. Assume b=2.625 in., t-tw=0.375 in. and d=4.625…
A:
Q: / Act on the structure in Figure 4 horizontal force NK Finally, D. Find the effect of the reaction…
A:
Q: 1. Based on the governing equation of the fluid mechanics derive the relationship between the speed…
A: When one or more of the known (i.e. independent) variables change, the governing equations of a…
Q: Air enters the compressor of an ideal air-standard Brayton cycle at 96 kPa, 310 K, with a volumetric…
A:
Q: Air is kept in a tank at pressure Po = 689 KPa abs and temperature To = 17°C. If one allows the air…
A: Given: Stagnation pressure = 689 kPa Stagnation temperature = 17+273 = 290 K Exit pressure = 101.325…
Q: Given a workpiece below all dimension are in inches. Determine: (a) the taper length of section A,…
A: Given : To find : (a) the taper length of section A, (b) the degree setting to taper turn section…
Q: Class A cantilever beam AB of circular cross section and length L=450 mm supports a load P-400 N…
A:
Step by step
Solved in 2 steps
- A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
- The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.
- The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.A circular aluminum tube of length L = 600 mm is loaded in compression by forces P (see figure). The outside and inside diameters are d2= 75 mm and d1= 63 mm, respectively. A strain gage is placed on the outside of the lube to measure normal strains in the longitudinal direction. Assume that E = 73 GPa and Poissons ratio is v = 0.33. (a) IF the compressive stress in the tube is 57 MPa, what is the load P? (b) If the measured strain is e = 78 J X 10-6, what is the shortening(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
- • - 3 A rectangular plate in biaxial stress (see figure) is subjected to normal stresses u = 67 MPa (tension) and s = -23 MPa (compression). The plate has dimensions 400 X 550 X 20 mm and is made of steel with E = 200 GPa and v = 0.30. (a) Determine the maximum in-plane shear strain ?max in the plate. (b) Determine the change ?t in the thickness of the plate. (c) Determine the change ?t in the volume of the plate.Rectangular bars of copper and aluminum are held by pins at their ends, as shown in the figure. Thin spacers provide a separation between the bars. The copper bars have cross-sectional dimensions 0.5 in. × 2.0 in., and the aluminum bar has dimensions 1.0 in. × 2.0 in. Determine the shear stress in the 7/16-in. diameter pins if the temperature is raised by 100°F. (For copper, Et= 18,000 ksi and ac = 9.5 × 10-6/?; for aluminum, Ea= 10,000 ksi and aa= 13 × 10-6/?.) Suggestion: Use the results of Example 2-10Plastic bar of diameter d = 32 mm is compressed in a testing device by a Force P = 190 N that is applied as shown in the figure. (a) Determine the normal and shear stresses acting: on all faces of stress elements oriented at (1 ) an angle 8 = 00, (2) an angle ?? = 22.5s, and (3) an angle ?? = 45°. In each case, show the stresses on a sketch of a properly oriented element. What are smaxtmax (b) Find smax and tmax in the plastic bar if a re-cantering spring of stiffness k is inserted into the testing device, as shown in the figure. The spring stillness is 1/6 of the axial stiffness of the plastic bar.