steel rod: 0 24 mm 0.4 m 3 m Figure 1.23 A rectangular column of sides 0.4m x 0.35m, made of concrete, is used to support a compressive load of 1.5MN. Four steel rods of each 24mm diameter are passing through the concrete as shown in figure 1.23. If the length of the column is 3m, determine the normal stress in the steel and the concrete. Take Esteel = 200 GPa and Econcrete = 29 GPa. %3D %3D 0.35 m

steel rod: 0 24 mm 0.4 m 3 m Figure 1.23 A rectangular column of sides 0.4m x 0.35m, made of concrete, is used to support a compressive load of 1.5MN. Four steel rods of each 24mm diameter are passing through the concrete as shown in figure 1.23. If the length of the column is 3m, determine the normal stress in the steel and the concrete. Take Esteel = 200 GPa and Econcrete = 29 GPa. %3D %3D 0.35 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.9P: A cylinder filled with oil is under pressure from a piston, as shown in the figure. The diameter d...

See similar textbooks

Similar questions

A cylinder filled with oil is under pressure from a piston, as shown in the figure. The diameter d of the piston is 1,80 in. and the compressive force F is 3500 lb. The maximum allowable shear stress t^^, in the wall of the cylinder is 5500 psi. What is the minimum permissible thickness t„± of the cylinder wall? (Sec figure
A beam with the mass of 3 Mg is hanging from cables. The center of gravity is directly below the point where the two cables meet and the two cables are at angles 0 = 25°, and = 30°. Let the diameter of cable AC be 12 mm. Find the diameter of cable AB so that it has the same normal stress as cable AC. B BY NO SA 2021 Cathy Zupke The diameter of cable AB is A e mm G e C
Find the stress acting on the surface of a thin sphere of diameter 15 cm, thickness 0.25 cm and the internal pressure is 2 MPa
A closed thin walled cylindrical vessel has a diameter D of 470 mm, a wall thickness t, and length L of 500 mm. It is subject to an internal pressure P of 0.16 MPa. Calculate the minimum wall thickness of the vessel if it has a limiting stress of 5 MPa. Give your answer in mm to 3 significant figures. de 00 $ de
A cylindrical tank of 15 m high and 5 m in diameter is to be filled with water. Find the minimum thickness of the tank plating if the ultimate stress is limited to 500 MPa and the factor of safety is 2.
H. W2: A rectangular column of sides 0.4mx0.35m, made of concrete, is used to support a compressive load of 1.5MN. Four steel rods of each 24mm diameter are passing through the concrete as shown in figure 1.23. If the length of the column is 3m, determine the normal stress in the steel and the concrete. Take Esteel 200 GPa and Econcrete = 29 GPa. steel rod: 0 24 mm 0.4 m 3 m 0.35 m
Question 24 A 3 m long hollow circular tube made from aluminium with an outside diameter 200 mm and a wall thickness of 10 mm is filled with a polymer matrix. It is subjected to a tensile axial force of 500 kN acting uniformly over the entire cross-sectional area of the filled tube. If the elastic modulus of the aluminium is E₂=75 GPa, and of the matrix is Em 15 GPa, calculate the normal direct tensile stresses acting on the two materials and the extension of the tube. = Which of the following answers is correct? The tensile stress in the aluminium is ten times larger than the tensile stress in the matrix The tensile stress in the aluminium is 45.2 MPa and the extension of the tube is 1.8 mm. The tensile stress in the matrix is 19.1 MPa and the extension of the tube is 3.1 mm. O The tensile stress in the matrix is 40.5 MPa and the extension of the tube is 2.5 mm. AMSUN The tensile stress in the aluminium is 54.7 MPa and the extension of the tube is 0.8 mm.
A closed thin walled cylindrical vessel has a diameter D of 290 mm, a wall thickness t of 5 mm and length L of 210 mm. It is subject to an internal pressure P of 18 MPa causing circumferential stress and longitudinal stress in the vessel. Calculate the longitudinal stress due to the internal pressure. Give your answer in MPa to 3 significant figures. 00 P D 60 de OL
1. Determine the internal stresses developed in bars JH and HY when bar JH experiences a change in temperature of -250•C. Bar JH is made of aluminum, while bar HY is made of steel. Both bars have the same cross-sectional area. Note: Pin H is connected to a wheel that is restricted to move along the inclined slope. J 450 H 1 m 250 Y 2 m Material a (/°С) E (GPa) Steel 11.9 x 10-6 200 Aluminum 22.5 x 10-6 70
1. A hydraulic system is used to apply a force in an external fixation device to hold broken ends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure (shaded portion of the sketch) is 3 MN/m² as shown in Figure QI.1. 3 MN/m 30 cm 4 cm Figure QI.I Hydraulic system Determine: 1.1. The stress in the piston rod which has dimeter of 4 cm 1.2. The elongation of the 2 m long piston rod. Take Young's modulus as E- 200 GN/m²
1. A thin-walled cylinder with a diameter of 20 cm and a wall thickness of 2 mm is filled with gas at a pressure of 2 MPa. Calculate the longitudinal stress, and circumferential stress in the cylinder wall.
An engineering machine component operating in a high temperature environment consists of a copper pipe having a cross-sectional area of 2 000 mm² and 0.3 m long, which is placed between two rigid caps. Four M22 steel bolts are symmetrically arranged around the tube and parallel to the axis of the tube and are lightly tightened. 3.1 Find the stress in the pipe and the bolts if the temperature of the assembly is increased from 25 °C to 95 °C. 3.2 What load will each bolt carry at the raised temperature? 3.3 Make a neat sketch of the assembly. (Est = 200 GPa, Ecu – 100 GPa, as: = 12 × 10-6/ °C, acu = 16 × 10-6/ °C)