A cylinder is to be supported as shown with the setup below. BC is a cable line having an area of 100 mm If the cable BC can only sustain a stress of 50 MPa, detemine the maximum mass that the cylinder can have6 m6 m4 mSelect the correct response611.62 kN6.12 kN0.61 kg611.62 kg

Answered: Image /qna-images/answer/ee1c716d-6d10-42c8-b216-c81b13929c54.jpg

Supported as shown with the setup below. BC is a cable line having an area of 100 mm. If the cable BC can only sustain a stress of 50 MPa, determine the maximum mass that the cylinder can have 6 m 6 m 4 m Select the correct response 611.62 kN 6.12 kN 0.61 kg 611.62 kg

Supported as shown with the setup below. BC is a cable line having an area of 100 mm. If the cable BC can only sustain a stress of 50 MPa, determine the maximum mass that the cylinder can have 6 m 6 m 4 m Select the correct response 611.62 kN 6.12 kN 0.61 kg 611.62 kg

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.4P: The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the...

See similar textbooks

Related questions

Q: what distance measured from the A of the cantilevered beam below is maximum internal moment?

A: Calculating the reaction at the support, RA+RB=12×4×300×+12×6×300RA+RB=1500 ........... (1)Taking m...

Q: What is the reading on this caliper? Please see attached image.

A: Given dial calipers Dimension to be measured =Blade scale reading + dial scale reading We see that...

Q: Q. A shaft rotating N rpm under a torque T transmits a power of answer choices T*Pi*N/30 Newton mete...

A: As given in question, Shaft RPM = N Torque transmitted by shaft = T From the shaft RPM, its angula...

Q: cylinder of 125mm radius rotates concentrically inside a fixed cylinder of 130mm radius. Both cylind...

A: Given Data Inner Radius=125 mm Outer Radius=130 mm L=300 mm w=2π rad/s

Q: For the simply supported beam shown below, determine the internal resultant loadings at a point 1 me...

Q: The tank is fined with water. Determine the resultant force acting on the triangular plate A and the...

Q: Q3 Use the graphing method to find the resultant and its direction of the forces shown in figure 1. ...

Q: e determine the resultant of the force system in next figure. And locate the resultant with respect ...

A: Given force system

Q: A rigid bar ABC is pinned at A and supported by the cables at point B as shown in the figure. The ro...

Q: A solid 1.500-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 190 lb-ft and T...

A: Given Datad=1.5inG=11,000ksiTB=190 lb-ftTD=140 lb-fta=42 inb=72 inc=36 in

Q: B: Find the total moment of force with respect to point (A), for the two forces in next fig. Sm 3m 5...

A: It is required to determine moment of force about point A

Q: 2. There were 42 mangoes in each crate. 12 such crates of mangoes were delivered to a factory. 4 man...

A: Answer: Mangoes total=42*12=504 Rotten/Thrown=504-4=500 boxes total 500/10=50

Q: A rod of length L=500 mm and cross-sectional area A=60 mm2 is made of an elastic-plastic material ha...

Q: Q5: Find the both moments of inertia (Ix, Iy) by integration around the central coordinates as shown...

Q: 3.) In In an actual Rankine cycle, steam first enters the turbine at 10 MPa and 400C. It expands to ...

Q: Q4 Find the moment about point O in figure 2. 25 N 45 2.25 m 40 N 20 N 2.75 m 2 m 30 15m 3 m 30 20N ...

A: It is required to determine moment about point O

Q: A certain gas weighs 16.0 N/m3 at a certain temperature and pressure. What are the values of its den...

A: Answer: (a) The density of gas is 1.6310 kg/m3. (b) The specific volume of gas is 0.613125 m3/kg. (c...

Q: 3.4 Consider a steady, incompressible, 2D velocity field for motion parallel to the x-axis with cons...

A: Given: The shear rate , dudy=Ay

Q: Water steam turbine generate 4 MWel power. Efficiency of turbine is 20%. How much wood chips ( by ma...

A: Given DataP=4kWηT=20%ηG=80%

Q: Determine maximum spring compression

A: Given: R=0.7 m b=1 m k=0.8 N/m μ=0.2 TO determine: The compression in spring

Q: Determine the total work performed by thr force field, F(x,y) =, on a particle that runs along the p...

A: We know that, r= (x)i + y(j) By differentiating, we can get, dr= (dx)i + (dy)j Given that, F=<2x+...

Q: An industrial adiabatic heat exchanger utilizes cold-water stream to cool down the waste-hot air flo...

Q: e mechanism shown in Figure P8.1 mass of 3.0 lbm and polar mass m tia of 0.04 lb-in-sec2 about its m...

A: T is torque because of moment of inertia and it acts upper direction and rotate in clo...

Q: Problem 3 A gate is 1.5m in width and hinged at point A. Another point on the gate. B. is resting ag...

Q: The power output of a steam turbine is 5 MW. The inlet conditions are 2 MPa of pressure, 400 degrees...

A: We know that a steam engine has a power output of 5 MW.2MPa pressure, 400°C temperature, 50 m/s velo...

Q: A steel [E=200 GPa] rod with a circular cross section is 10 m long. Determine the minimum diameter ...

A: Given data as per question Length of the bar =10 m Tensile force = 260 kN we know thatNormal stress ...

Q: 27 Find the transfer function Y(s) tem shown in Figure E2.27.

A: To find Transfer function

Q: what is the miller indices of (-2/3 -2/3 0)

A: Answer:

Q: Consider laminar flow of water over a flat plate of length 1 m. If the boundary layer thickness at a...

Q: A Use Cosine and Sine laws to find the missing lengths and angles in figures 3. 30 6. Figure 3

Q: Q 1: Find the Centroid of the Lamina in Fig. 1. (All units are in mm) 85 35 55 115 35 125

A: It is required to determine the centroid of given section n

Q: lied to gear Dof the gear train shown. The bearings shown allow the shafts to rotate freely. diamete...

Q: Write or introduce the following topics of ceramics: • Types of ceramics • Sintering • Metal process...

Q: ust be from the origin. 70 mm mm 60 mm 10 mm

A: Area symbol area mm2 x̄(mm) ȳ (mm) A x̄(mm3) A ȳ (mm3) A1 40*15=600 -62.5 27.5 -37500 1...

Q: Problem (5.4) A nozzle in an impulse turbine delivers 1 kg/s steam to a set of blades moving at 200 ...

Q: A heat pump consumes around 3 kW of power, minimum. If the outside temperature reached -2°C and the ...

Q: • The groups SU(2) and SO(3) are related. Write the form of the rotation about the z-axis of an angl...

A: Group SO(3)In this part, we start with an update on the pivots in three-layered Euclidean space whic...

Q: The engine of the helicopter is delivering 600 hp to the rotor shaft when the blade is rotating at 1...

A: The radius are calculated for both the conditions and bigger radius is considered for final selectio...

Q: A solid circular bronze [G = 6,500 ksi] shaft, 4.6 ft long and 1.575 in. in diameter, carries a torq...

A: Given Data L=4.6 ft G=6500 ksi D=1.575 in T=60 lb.ft

Q: 1. A vertical plate is submerged in water. Find an integral expression that can be evaluated to dete...

Q: Show that cot?t+ tan?t= 1is a possible form for the boundary surface of an incompressible flow when ...

A: For a 2-D incompressible steady flow to be possible it has to satisfy the continuity equation for a ...

Q: P = hp T= psi Save for L ater nter

A: To find power maximum shear stress

Q: of (302 K pa) and a temperature of C 502 K) enters Deter mine the back pres Sure wich is boneff nece...

Q: small ball slides around a horizontal circle at height y inside a frictionless emispherical bowl of ...

A: HHjajja

Q: For the given fluctuating fatigue load, the values of stress amplitude and stress ratio are respecti...

A: From the given figure, Maximum stress in the cycle = σmax = 250 MPa Minimum stress in the cycle = σm...

Q: 4. If the isentropic efficiencies of the turbine and the pump are 80% and 100% respectively in probl...

Q: The figure from an old patent application describes a right-angle belt drive between a pulley at C w...

Q: Homework F 52KN ) The slope of the 5.2-kN force F is specified as shown in the figure. Express F as ...

Q: Problem (5.3) The outlet angles of the nozzle and blades of a two-row impulse turbine are in success...

Q: : Find the total moment of force with respect to point (A), for the two forces in next fig. 8m 3m 50...

A: It is required to determine the moment of forces about point A

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A cylinder is to be supported as shown with the setup below. BC is a cable line having an area of 100 mm If the cable BC can only sustain a stress of 50 MPa, detemine the maximum mass that the cylinder can have
6 m
6 m
4 m
Select the correct response
611.62 kN
6.12 kN
0.61 kg
611.62 kg

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the ladder itself. Each ladder rail (t5= 4 mm) is supported by a shoe (ts= 5 mm) that is attached to the ladder rail by a bolt of diameter d = 8 mm
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
Questlon 4 The drive from a motor to a machine is by means of a crossed flat belt. The shat of the motor and the machine are parallel and 1.2 meter apart. The motor pulley A turns at 1440rpm and has a diameter of 250mm. The machine B rotates at 450rpm. The belt is made of lether. The safe tensile stress is 7MPA and the density is 900kg/m. The dimensions of the belt are 50mm x 6mm. p = 0.2. Dermine: The length of the belt required The maximum power that can be transmitted The maximum torque on the driving pulley The maximum torque on the driven pulley
touch &O O166% 00:27 MENG250 - Practice Assign... Problem 2-15 Determine the design angle ø (0° < ø< 90°) between struts AB and AC so that the 400-lb horizontal force has a component of 500 lb directed from A towards C. What is the component of force acting along member AB? Take 0 = 40°. 400 lb A te B
Which following ones are true? Calculate tension forces in the cables in the given figure. Weight of the crate is 20 N. -1.5i +1.5 j+3k V13.5 I:Foc = FDC 3 m 4.5 m 3,m 3i –1.5 j+3k F, V20.25 A II : F, 1.5 m 3 m DA DA D 1.5 m- III :FpB =-FDBj IV :W =-20k V:Fc+F +F +W =0 DC DA DB O A) Il and III are true but others are wrong O B) all of them are true C) none of them are true O D) II, IV, V are true but others are wrong O E) I and II are true but others are wrong
Calculate the maximum force P that can be applied in a phosphor bronze spring having mean diameter of 150 mm and consisting of 24 turns of 10-mm diameter wire when the spring is stretched 180mm. Use G = 42 GPa. Group of answer choices 233.11 N 113.33 N 116.667 N 225.56 N
ZV. 0 3 ull ull zain 1Q zain IQ The rod BD is made of material with G1= 110 GPa has a diameter 18 mm is bonded to the tube CA at point B, the tube made of material with G2=187 GPa has an outer diameter 41 mm and wall thickness of 10 mm. If T1=1424 N.m and T2=2563 :N.m, answer the following questions A B T2 N-m 0.4 m 0.1 m D 0.3 m T1 N-m The polar moment of inertia of the rod BD is إجابتك The polar moment of inertia of the tube CA is احابتك
A safety valve spring having 9 and 2 coils has the ends squared and ground. The outside diameter of the coil is 115 mm and the wire is 13 mm. It has a free length of 203 mm. The length of which this spring must be initially compressed to hold a boiler pressure of 1.38 MPa on the seat of 32 mm diameter. Modulus of rigidity is taken as G=80GN/m?. Find the force acting on the valve set. Compute the Wahl factor
Use the Method of Sections to find the load in member EK of the bridge. Is it in tension or compression? Record your answer in kN. A B Q 1m P 1m 1m N 1m M 1m 1m K 1m 1m 1m 10kN 10kN 10kN 10kN 10kN 10kN 10kN 10kN 10kN 1m, H 2m
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
A safety valve spring having 9 and 2 coils has the ends squared and ground. The outside diameter of the coil is 115 mm and the wire is 13 mm. It has a free length of 203 mm. The length of which this spring must be initially compressed to hold a boiler pressure of 1.38 MPa on the seat of 32 mm diameter. Modulus of rigidity is taken as G=80GN/m?. a. Find the force acting on the valve set. b. Determine the mean diameter c. Determine the spring index d. Find the spring deflection e. Find the operating length f. Calculate the solid length g. Calculate the deflection of solid length h. Compute the solid force i. Compute the Wahl factor