The 622-N force is applied to the 112-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. = 0.71 Hk = 0.57 Answer: F - I 24° N P = 622 N

The 622-N force is applied to the 112-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. = 0.71 Hk = 0.57 Answer: F - I 24° N P = 622 N

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter6: Applications Of Newton’s Laws Of Motion

Section: Chapter Questions

Problem 8PQ: A rectangular block has a length that is five times its width and a height that is three times its...

See similar textbooks

Similar questions

A 235 N force acts on a bike in a direction 17° N of W. Determine graphically and analytically the components of the force.
Find the magnitude (in N/m) and direction (in degrees counterclockwise from the +x-axis) of the force that each wire experiences in the figure by using vector addition. (Assume that the +x-axis is to the right and the +y-axis is up along the page.) 6.50 A X. 19.5 A 45.5 A +13.0 cm- Top wire magnitude 0.000577 N/m direction 103 ° counterclockwise from the +x-axis Bottom left wire magnitude 0.00127 N/m direction 306 ° counterclockwise from the +x-axis Bottom right wire magnitude 0.00119 N/m direction 254 ° counterclockwise from the +x-axis 13.0 cm- -13.0 cm-
The 633-N force is applied to the 106-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. P = 633 N 38° = 0.66 H = 0.43 Answer: F = i N
A 1520-N crate is to be held in place on a ramp that rises at 30.0° above the horizontal (see figure). The massless rope attached to the crate makes a 22.0° angle above the surface of the ramp. The coefficients of friction between the crate and the surface of the ramp are uk = 0.450 and ls = 0.650 The pulley has no appreciable mass or friction. What is the MAXIMUM weight w that can be used to hold this crate stationary on the ramp? w = ? 22.0° Crate Ramp 30.0°
A rectangular block has a length that is five times its width and a height that is three times its width. The blocks surfaces are all identical except for size. When the block is placed on a horizontal tabletop so that the area in contact with the table is length width, it is found that a horizontal force of 10.0 N applied to the block is just sufficient to overcome the static friction force and cause the block to move. The block is then knocked over so that the area in contact with the table is length height. Now, what minimum horizontal force will cause the block to move? Explain.
Lisa measured the coefficient of static friction between two pairs of running shoes and the track in Example 6.1 (page 159). If she wants to have an advantage in a race, which shoes should she wear, the ones with a high coefficient or the ones with the low coefficient of static friction? Explain.
From Fig. P-014, P is directed at an angle a from x-axis and the 200 N force is acting at a slope of 5 vertical to 12 horizontal. a. Find P and a if the resultant is 500 N to the right along the x-axis. b. Find P and a if the resultant is 500 N upward to the right with a slope of 3 horizontal to 4 vertical. c. Find P and a if the resultant is zero. 12 200 N Figure P-014
Question 2 Figure 2 shows a 2-story steel frame with h = 4 m and b = 6 m, determine the equivalent horizontal forces (EHF) for both floors under the following actions: Dead load = 20 kN/m Imposed load = 12 kN/m Students can make their own rational assumptions for any information which they think is required but not provided. Clear state the assumptions and the corresponding justifications. W W b Figure 2 h
Determine the magnitude of the x- component of force Q (in N) if P=96.4 N, Q = 55.2 N , 0= 55.53° and a = 49.46°.Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the x-component. Use R if to the right, L if to the left, U if upward or D if downward. y P
What is the moment of friction force f(B) at Babout point A? O A) the moment of friction force f(B) at Babout point A is 220 Ib.ft B) the moment of friction force f(B) at Babout point A is zero O C) the moment of friction force f(B) at Babout point A is 320 Ib.ft D) the moment of friction force f(B) at B about point A is 120 Ib.ft O E) the moment of friction force f(B) at Babout point A is 420 Ib.ft
A 3.0-N block slides on a frictionless inclined plane. Which one of the following statements is true concerning the normal force that the plane exerts on the block? Ø The normal force is 3.0 N. The normal force is less than 3.0 N, but greater than zero newtons. The normal force is greater than 3.0 N. It increases as the angle of inclination, 0, is increased. The normal force is zero newtons.
A 1.850 kg block of wood rests on a steel desk. The coefficient of static friction between the block and the desk is us = 0.555 and the coefficient of kinetic friction is Hk 0.305. At time t = 0, a force F 6.19 N is applied horizontally to the block. State the force of friction applied to the block by Us.k the table at times t = 0 and t > 0. t = 0 6.19 N 1 > 0 6.19 Consider the same situation, but this time the external force F is 12.5 N. Again, state the force of friction acting on the block at times t = 0 and t > 0. 5.53 t > 0 5.53 t = 0 N Incorrect