The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If the allowable shear stresses for the magnesium and steel are (Tallow)mg = 45 MPa and (Tallow)st = 75 MPa, respectively, determine the maximum allowable torque that can be applied at A. Also, find the corresponding angle of twist of end A. O O 900 mm 80 mm/ 40 mm T

The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If the allowable shear stresses for the magnesium and steel are (Tallow)mg = 45 MPa and (Tallow)st = 75 MPa, respectively, determine the maximum allowable torque that can be applied at A. Also, find the corresponding angle of twist of end A. O O 900 mm 80 mm/ 40 mm T

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Dr. A H.W.5: A rigid bar ABCD is supported by two bars, as shown in Fig- ure 3 .There is no strain in the vertical bars before load Pis applied. After load P is applied, the normal strain in rod (1) is -570 pm/m. Determine (b) the normal strain in rod (2) if there is a l-mm gap in the connection at pin C before the load is applied. (c) the normal strain in rod (2) if there is a l-mm gap in the connection at pin B before the load is applied. (a) the normal strain in rod (2). (2) 1,500 mm 360 mm 140 mm 240 mm Rigid bar bber C B 900 mm (1)
The Am1004-T61 magnesium tube is reinforced with the bonded A-36 steel rod. If the allowable shear stresses for the magnesium and steel are (τallow)mg = 45 MPa and (τallow)st = 80 MPa, respectively, determine the maximum torque T that can be applied at A. Additionally, find the corresponding angle of twist of end A.
The compound shaft, which is fixed at both ends, is composed of Aluminum shaft ABC (Gal = 24 GPa, d = 50 mm), steel sleeve AB (Gst = 76 GPa, dout = 90 mm), and copper sleeve ABC (Gcu = 45 GPa, dout = 75 mm), which are all welded together. Considering the allowable shear stresses (Tal, Ist, Tcu), determine the maximum allowable torque T (kN-m) that may be applied at B as shown. Note: Double-headed arrows follow the direction of the thumb when using the right-hand rule. A Parameters Tal = 51 MPa Tst = 101 MPa Tcu = 71 MPa steel Cu AI L = 5m B ➡T Cu AI L= 3.5m C
*4-76 The C83400-red-brass rod AB and 2014-T6-alu- minum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T₁ = 50°F, determine the average normal stress in each member when T₂ = 120°F. Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in². 3 ft B 2 ft C
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E=205GPA, G,A=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x104mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vD 2. The normal strain in member AD, CAD 3. The average stress experienced by pin A, TA 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
4-47. The support consists of a solid red brass C83400 post surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts is 1 mm. Determine the greatest axial load that can be applied to the rigid cap A without causing yielding of any one of the materials. A 0.25 m = 1 mm 60 mm 80 mm Prob. 4-47 -10 mm
he 40-Kip vertical load at Joint C i the stec ying table. The cross-sectional ay er is given in the table. The elastic t (in.) of Joint C is most ‘nearl; FE CIvIL PRACTICE EXAM iven in the el truss shown below produces the foroles e rea of each member is 4.0 in’, and the length S modulus of steel is 29,000 ksi. The downward y: Member Rorce ki Length, L (kips) i AB 500 BC 492 cp 750 AD -30.0 BD 2250
Link AC is made of a steel with a 450-MPa ultimate normal stress and has a 6 x 12-mm uniform rectangular cross section. It is connected to a support at A and to member BCD at C by 8-mm diameter pins, while member BCD is connected to its support at B by a 10-mm diameter pin. All the pins are made of steel with a 170-MPa ultimate shear stress and are in single shear. Kwing that a factoaety f32is desired. 12 mm 200 mm It is required to determine the largest load P that may be applied at D. Note that link AC is not reinforced around the pin holes. 150 mm 10
The frame is subjected to the load of 200 lb. Determine the average shear stress in the bolt at A. The bolt has a diameter of 0.25 inches and in single shear. ID 2 ft 1.5 ft 200 lb B 0.5 ft
Q-1 Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa.c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4.
5 A flanged bolt coupling has ten 12-mm di ameter steel bolts on 500 mm diameter b olt circle and six 16 mm diameter aluminu m bolts on 300 mm diameter bolt circle. Determine the maximum torque that can be applied without exceeding the shear s tress of 60 MPa in steel or 40 MPa in alu minum. Use G = 80 GPa for steel and 30 GPa for aluminum. Drawing not included in this problem.(
The steel tie bar shown is to be designed to carry a tension force of magnitude P = 120KN when bolted between double brackets at A and B. The bar will be fabricated from 20-mm-thick plate stock. For the grade of steel to be used, the maximum allowable stresses are: o = 180 MPa, t = 120 MPa, op = 380 MPa. Design the tie bar by determining the required values of: a. the diameter d of the bolt, b. the dimension b at each end of the bar, c. the dimension h of the bar.