The bracket is fastened to the girder by means of the two rivets A and B and supports the 2-kN force. Re- place this force by a force acting along the centerline between the rivets and a couple. Then redistribute this force and couple by replacing it by two forces, one at A and the other at B, and ascertain the forces supported by the rivets. Ans. F = 0.8 kN F = 2.8 kN A 250 mm 100 mm 2 kN 300 mm

The bracket is fastened to the girder by means of the two rivets A and B and supports the 2-kN force. Re- place this force by a force acting along the centerline between the rivets and a couple. Then redistribute this force and couple by replacing it by two forces, one at A and the other at B, and ascertain the forces supported by the rivets. Ans. F = 0.8 kN F = 2.8 kN A 250 mm 100 mm 2 kN 300 mm

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 26P: Find the magnitude of the tension in each supporting cable shown below. In each case, the weight of...

See similar textbooks

Similar questions

There are two forces on the 1.45 kg box in the nverhead view of the figure but anly ane is shown, For Fa- 20.7 N,a - 11.4 ms?, and A- 25.6, find the second force (a) in unit-vector notation and as (b) a magnitude and (c) a direction. (State the direction as a negative angle muasured from the tx dlirectiun.) (a) Number i+ i Units (b) Number Units (c) Number Units
Find the resultant of force Y 390 Ib MATHalino.com 12 30 1 1 300 lb 722 Ib Figure P-265
ourses This course ion 1 The 10-kg pipe is supported at A by a system of five cords. Determine the force in the cable AB for equilibrium: et ered d out of on 60° Select one: O a. T(AB) = 226.56 N O b. T(AB) = 113.28 N O c. T(AB) = 593.83 N O d. None of these cht W nf the block, shown in the following figure, so that the tension developed in an
AB rigid made of a smooth materialbar on a frictionless horizontal surface.is standing. A force of 2 N at end A of the rodapplied perpendicular to the length of the bar.Since the weight of the bar is 3 kg, A and BCalculate the accelerations of the points.
SAQ 1 1.2 m D C An 80-kn'm couple shown in the plate is caused by a pair of parallel forces of magnitude F (not shown). Determine: 80 kN m a) the smallest possible value of F, and 1.6 m b) the value of F if the forces act at points A and C and are parallel to the dashed line shown at A. A В 60°
The tube, shown below, is supported by two cables (AB) and (AC). A force F = 600 lb is applied in cable AB. The component of the force Facting along cable (AC) is: |3 ft E 8 ft- В 12 ft 8 ft 15 ft Select one: a. 49.509 [lb] O b. 495.708 [lb] c. 600 [lb] O d. 459.708 [lb]
The mast of a ship supports forces from three cables as shown. If F= 350 lb, determine the value of a that minimizes the magnitude of the resultant of the three forces. Also, determine the magnitude of that resultant. 800 1b 600 lb The value of a that minimizes the magnitude of the resultant is , and the magnitude of the resultant is lb.
Q1 Q1\ ABD consists Isosceles triangle. The AB and AD help support pole AC. Known that the tension in AB is double AD tension and the distance between A and C is 0.7 of BD. Determine the magnitude of these tensions if the value of resultant forces is 120 Ib. B.
A block of weight w is suspended from a rope tied to two other ropes at point O. One rope ishorizontally attached to a wall and the other is fastened to the ceiling. The angle betweenceiling and the rope is 60°. What are the tensions in each of the ropes? Assume the weights ofthe ropes and the knots are negligible. If the weight of the block is 100 N, what is the tension inthe ceiling rope?
The uniform plank ABC weighs 400 N. It is supported by a pin at A and a cable that runs aroundthe pulley D. Determine the tension in the cable and the components of the pin reaction at A. Note thatthe tension in the cable is constant
A 60.0 cm, uniform, 50.0 Nshelf is supported horizontally by twov verticalwires attached to the slopingc ceiling(Fig. ). A very small 25.0 N tool is placed on the shelf midway between the points where the wires are attached to it. Find the tension in each wire. Begin by making a free-body diagram of the shelf.
A. Find the tension in the cable B. Find the horizontal component of the force exertedC. Find the vertical component of the force exerted on the beam at the wall