The canal shown below runs 40 m into the paper. Assume unit weight of H2O is 9.79 kN/ m^3. Compute the location of the center of pressure where the resultant strikes the wall measured Vertically and horizontally from the bottom of the quarter circle wall. 18m 40 18m 18 Unit of the Correct Answer: meter Decimal Places required in the final answer: n/a X = 7.639, Y = 6

The canal shown below runs 40 m into the paper. Assume unit weight of H2O is 9.79 kN/ m^3. Compute the location of the center of pressure where the resultant strikes the wall measured Vertically and horizontally from the bottom of the quarter circle wall. 18m 40 18m 18 Unit of the Correct Answer: meter Decimal Places required in the final answer: n/a X = 7.639, Y = 6

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

As- 1400 m ? b,= 1200 mm Pi= 1900 N/ mm? Li: 6 KN/m 40 MPa 180 fc= LCspan) = 20 m 1200 200 300 Assume 20%. loss @ working /ervice Canditians Determine Vci * Vcw @ 500 mm from hirge support Force in tendon = P e = egl 1 2.5m 2.5m
12- What is the value of earthquake velocity response spectrum for Tn=0? a) b) c) d) e) Zero ton. 0. kN. Zero m/s. Zero m/s2 Zero m.
The cantilever beam is loaded as shown in Figure Q2 (b). Use method of moment area to determine slope at point B and deflection at point C. Take EI as constant.
PROBLEM 2:A triangular gate having dimensions shown is hinged at its top at A. The gate rests on a frictionless surface at B. 4m seawater (SG=1.031) 60° 2m BA a. Determine the hydrostatic force acting on the gate. * Your answer b. At what distance from the centroid of the panel is the hydrostatic force acting? * Your answer IMI 21
10:58 1 Seatwork 1 (Normal Stress) A NAME: DATE COURSE/YEAR/SECTION: SEATWORK #1 01. The two-bar structure shown is pinned at A, B, and C. A sign weighing 20 kN is suspended from bar BCat points Dand E, which are located at 0.8 m and 0.4 m, respectively, from the ends of the bar BC. If member AB is a steel pipe with inside diameter 20 mm, determine the smallest permissible outer diameter of the member if the working stress in steel is not to exceed 140 MPa. SUMMARY OF ANSWERS 2.0 m do D 0.9 m -0.9 m 0.8 m 04 m W= 20 kN 02. Determine the smallest allowable cross-sectional areas of members JK, DK, and DE of the truss shown. The working stresses are 120 MPa in tension and 80 MPa in compression. (A reduced stress in compression is specified to reduce the danger of buckling.)
Section-B A rough pipe of diameter 45 cm and length 500 m carries water at the rate of 0.4 m³/s. The wall roughness is 0.012 mm. Determine: (i) the coefficient of friction (ii) wall shear stress (iii) centre-line velocity (iv) velocity at a distance of 15 cm from the pipe wall Take d 210g10+1. +1.14
Example 3 • Given: Figure • Find: External reactions in x and y directions needed to hold fixed vane. • Solution: Viny OINS = 0.90) 30 F V,-28 mA Q-0.20 m/s V;-27 m/s HAFU CE Dept., Course, 12
Problem III. Figure (a) shows a channel section that has an area of 3790 mm? and its moment of inertia about the x and y axes are lx = 25.3 x 10€ mm* and ly = 1 x 10° mm“. Now, figure (b) shows a section where two of the same channel section in Fig (a) are riveted together. EI 14.8 mm (a) (b) a) What are the moment of inertia about x and y axes of the composite section? b) Determine the radius of gyration about x and y axes. c) If the moment of inertia about the x-axis is to be transferred to an axis found at the topmost fiber of the composite section, what will be its value?
SHOW SOlution Ans. F= 733.16kN 1.844m from the bottom of the tank parallel to the gate
Complete the differential level notes shown below, and determine the difference in elevation of TP2 and BM11 STA BM 10 2.085 ТР1 BS (m) HI (m) FS (m) | ELEVATION (m) 137.450 2.015 0.982 1.428 1.864 BM11 0.423 TP2 2.423 а. 1.441 m b. 2.0 m c. 0.559 m d. 1.005 m е. 0.995
b ... oil d water A vertical rectangular plate is submerged half in oil (SG = 0.83) and half in water as shown. Determine the ratio of force exerted by water to that of oil. A 3.25 B) 3.21 C) No answer among the choices D) 3.29 E) 3.16
PROBLEM NO. A simply supparted bratt with overhang on the right suppert is shown belaw. Using virtual work method, determine the following Use:E= 200 000 MPa, 1 = 50 x10 mn 120 kNim 120 kN/m -20m -20m- 20m A Resultant reaction at support A. Deflection at mitdspan of segment AC C Slope of deflection at point .