The cantilever beam is subjected to a concentrated load of P = 59 kips. The cross-sectional dimensions of the wide-flange shape are shown in the second figure. Assume yμ = 3.8 in., yk= 1.3 in., d = 12.5 in., tw=0.309 in., t= 0.319 in., bf=5.07 in. Determine: (a) the shear stress that point H, which is located 3.8 in. below the centroid of the wide-flange shape. (b) the maximum horizontal shear stress Tmax in the wide-flange shape.

The cantilever beam is subjected to a concentrated load of P = 59 kips. The cross-sectional dimensions of the wide-flange shape are shown in the second figure. Assume yμ = 3.8 in., yk= 1.3 in., d = 12.5 in., tw=0.309 in., t= 0.319 in., bf=5.07 in. Determine: (a) the shear stress that point H, which is located 3.8 in. below the centroid of the wide-flange shape. (b) the maximum horizontal shear stress Tmax in the wide-flange shape.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
THE BEAMS SHOWN IN FIGURES (a) AND (b) HAS THE FOLLOWING PROPERTIES. f’c =30 MPa, fy=400 MPa AND IS SUBJECTED TO A POSITIVE BENDING MOMENT Mu=140KN-m. ANSWER THE FOLLOWING.1. DRAW THE INTERNAL STRESS AND STRAIN DIAGRAM OF BEAM CONSIDERING THAT THE DEPTH OF THE STRESS BLOCK IS GREATER THAN THE THICKNESS OF THE FLANGE.
Question 1. The plane NN' makes an angle 8-30" with respect to the cross section of theprismatic bar shown in Figure. The dimensions of the rectangularcross section of the bar are 3cmx6cm. Under the action of an axial tensile load P, the normal stress of NN' plane is o, =60 MPa. a.Determine the value of axial load P b.Determine the shear stress t on the NN' plane c. Determine the maximum shear stress in the bar. P N'
The internal shear force V at a certain section of an aluminum beam is 8.5 kN. If the beam has the cross section shown (assume a=32 mm, bf=65 mm, tw=tf-7 mm, d=89 mm), determine: (a) the shear stress T at point H, which is located 32 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape. a Answers: (a) TH i MPa. (b) Tmax MPa. H = bf y V d
Since the bending safety stress σem = 10 MPa, shear safety stress Tem = 600 kPa of the rectangular section beam given the loading status in the figure and width b = 150 mm, how much should the height h of the beam section be at least so that the stresses that will occur in the beam do not exceed the safety stress values. .
The cross-sectional dimensions of the beam shown in the figure are a = 4.1 in., b= 5.1 in., d= 4.3 in., andt= 0.33in. The internal bending mornent about thez centroidal axis is M, = -4.15 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. b y |(ур.) |d a Answers: (a) OmaxT psi (b) Omax C= psi
The internal shear force V at a certain section of an aluminum beam is 10.5 kN. If the beam has the cross section shown (assume a=31 mm, bf-62 mm, tw-tf-6 mm, d=63 mm), determine: (a) the shear stress TH at point H, which is located 31 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape. a Answers: (a) TH i MPa. (b) Tmax i MPa. H y bf = V tw d
Determine the shear stress at points: A, B. C, D and E in beam shown in Figure 5. Take E-30 GPa
The cross-sectional dimensions of the beam shown in the figure are a = 4.9 in., b = 6.8 in., d = 4.5 in., and t = 0.30 in. The internal bending moment about the z centroidal axis is M2 = -3.65 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. b y (ур.) d a Answers: (a) Omax T psi (b) Omax C= psi
SOLVE THE PROBLEM USING DOUBLE INTEGRATION METHOD Problem II. The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminum rod. Find the maximum allowable value of the applied force P if the stress in the rod is not to exceed 120 MPa. Use Est = 200 GPa, I = 50 x 10 mm4 for the beam, Eal = 70 GPa, and A = 42 mm² for the rod. 5 m 2 m Aluminum -Steel 2 m C
The cross-sectional dimensions of the beam shown in the figure are a = 4.6 in., b = 5.7 in., d = 4.9 in., and t= 0.31 in. The interna bending moment about the z centroidal axis is M_= -4.45 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam.
The cantilever beam is subjected to a concentrated load P. The cross-sectional dimensions of the rectangular tube shape are shown in the second figure. Assume b = 133 mm, d = 207 mm, y = 62 mm, yk = 37 mm and t = 6 mm. (a) Compute the value of Q that is associated with point H, which is located 62 mm above the centroid of the rectangular tube shape. (b) If the allowable shear stress for the rectangular tube shape is 117 MPa, determine the maximum concentrated load P that can be applied to the cantilever beam. Answers: (a) Q = (b) P = i i P Z mm³. kN. ун Ук H K b t (typ.)