The coefficients of permeability of a soil in horizontal and vertical directions are 3.48 and 1.5 m/day respectively. The base length of a concrete dam resting in this soil is 100 m. When the flow net is developed for this soil with 1:25 scale factor in the vertical direction, the reduced base length of the dam will be m

The coefficients of permeability of a soil in horizontal and vertical directions are 3.48 and 1.5 m/day respectively. The base length of a concrete dam resting in this soil is 100 m. When the flow net is developed for this soil with 1:25 scale factor in the vertical direction, the reduced base length of the dam will be m

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.17CTP

See similar textbooks

Similar questions

1. (30 pts) The soil profile shown below consists of 10 meters of sandy silt overlying gravel. The pore water pressure at the top surface of the silty sand is zero and can be assumed to remain zero. a) Calculate the level to which water would rise in a piezometer tube inserted into the top of the gravel if the silty sand is just stable? Use submerged unit weights and seepage forces to arrive at your answer (do not calculate total stresses and pore water pressures). Express your answer as an elevation, e.g. "Elev. 130". (Note: Elevations are in meters) (10 pts) b) Using the piezometric elevation calculated in part (a), calculate the pore water pressure at the bottom of the silty sand if the silty sand is just stable (10 pts). c) Calculate the total stress at the base of the silty sand and show that it is equal to the pore water pressure calculated in part (b) (10 pts) Elev. 120 m. Elev. 110 m. Sandy Silt (saturated) Void ratio, e = 0.68 G = 2.65 Gravel
For a falling-head permeability test, the following values are given: Length of specimen = 200 mm %3D Area of soil specimen = 1000 mm^2 %3D Area of standpipe = 40 mm^2 Head difference at time t = 0 = 500 mm Head difference at timt t 180 seconds = 350 mm %D %3D Determine the hydraulic conductivity of the soil in x10 4 cm sec
As shown in the figure given below, a 5 m thick layer of silty sand overlies a clay layer 3 m in thickness. Below the clay layer, there lies a 4 m thick gravelly sand layer underlain by pervious bedrock. The ground water table is at the ground surface. GWT Silty Sand 5 m Ya = 18 kN/m³ Ys = 19 kN/m3 Clay 1.5 m 3 m Ys = 18 kN/m3 x A Gravelly Sand Ys = 20 kN/m3 2 m 4 m x B WXXX a) Calculate the total stress (0), pore water pressure (u) and effective stress (o') at points "A" and “B". Show your work and tabulate the results in the following form. Point A Point B o (kPa) u (kPa) o' (kPa) b) If ground water table is lowered by 2 m for foundation excavation purposes, calculate the total stress, pore water pressure and effective stress at points "A" and "B" (i) immediately after, (ii) long time after lowering the water table. Show your work and tabulate the results in the following form.
A canal is cut into a soil with a stratigraphy as shown. Assume that flow takes place horizontally and vertically through the sides of the canal and vertically below the canal. The values of k in each layer is given. a. What is the equivalent permeability in the horizontal direction through the sides of the canal in cm/day? b. What is the equivalent permeability in the horizontal direction through the sides of the canal in cm/day? c. Determine the equivalent permeability in the vertical directions below the bottom of the canal, in cm/day. 1.0 m k = 2.3 x 10* cm/s 1.5 m T. k = 5.2 x 10 cm/s 3.0 m 2.0 m k = 2 x 10 cm/s 1.2 m k- 0.3 x 10 cm/s 3.0 m k = 0.8 x 10° cmn/s
The following data are for a falling-head permeability test:• Length of the soil sample = 150 mm• Area of soil sample = 1964 mm^2• Area of the standpipe = 25 mm^2• At time t = 0, head difference = 400 mm• At time t = 8 min, head difference = 200 mma. Determine the hydraulic conductivity of the soil (cm/sec). (ans. 2.75x10^-4 cm/s)b. What was the head difference at t = 6 min? (ans. 23.82cm)
2. Consider the stratified soil deposit shown in the figure. There are four layers, 3m thick each, and kH1=2x10³, kH2=1x105, kµ3=2x104, kH4=1x10³in cm/sec. Determine the equivalent coefficient of permeability in the horizontal direction and the total flow in cm3/sec per cm width. H Direction of flow
For a variable head permeability test, these values are given:• Length of the soil specimen 200 mm• Area of the soil specimen 1000 mm2• Area of the standpipe 40 mm2• Head difference at time t 0 is 500 mm• Head difference at time t 3 min is 300 mma. Determine the hydraulic conductivity of the soil in cm/sec.b. What was the head difference at time t 100 sec?
Given the following: H1 = 1.5 m H2 = 3.0 m H3 = 2.0 m K1 = 0.001 cm/sec K2 = 0.032 cm/sec K3 = 0.000041 cm/sec 1. Find the effective average permeability of the deposit in the horizontal direction. (in cm/s) 2. Find the effective average permeability of the deposit in the vertical direction. (in cm/s) 3. What is the ratio of the equivalent hydraulic conductivity?
Water flows through a sand filter as shown on the figure. The soil has a cross sectional area of 0.39 m². d1=d2=d3=0.52 m. Head difference is 0.93 m. Inflow Outflow Soil A Soil B Soil C d2 d3 Coefficient of Permeability for Each Soil: Soil A Kax 2.92 x 10-2 cm/s Soil A Kaz 1.36 x 10-3 cm/s Soil B Kbx 1.67 x 10.2 cm/s Soil B Kbz 2.92 x 10-3 cm/s Soil CKcx 3.28 x 102 cm/s Soil C Kcz 3.49 x 10-3 cm/s Compute the coefficient of permeability of the sand filler in cm/s. Use 4 decimal places
For a falling-head permeability test, the following values are given:• Length of specimen 8 in.• Area of soil specimen 1.6 in.2• Area of standpipe 0.06 in.2• Head difference at time t 0 20 in.• Head difference at time t 180 sec 12 in.Determine the hydraulic conductivity of the soil in in./sec
The figure shows a granular soil in a tank having a downward seepage. The water level in the tank is held constant by adjusting the supply from the top and the outflow at the bottom. The void ratio of the soil is 0.50 and the specific gravity is 2.7. H,0 0.8 m 1.1 m A 3.6 m 5.4 m B C Il a plezometer is placed at point B, to what height the water will rise above this point?
Refer to Figure 7.24. The following data were collected during the field permeability measurement of a confined aquifer using a pumping test. Determine the hydraulic conductivity of the permeable layer. Use Eq. (7.49). Thickness of the aquifer, H = 4.5 m Piezometric level and radial distance of the first observation well: h1 = 2.9 m; r1 = 17.8 m Piezometric level and radial distance of the second observation well: h2 = 1.8 m; r2 = 8.1 m Rate of discharge from pumping, q = 0.5 m3/min