The cold forming process in which a hardened tool is pressed against a workpiece (when there is relative motion between the tool and the workpiece) to produce a roughened surface with a regular pattern is A. Strip rolling B. Knurling C. Roll forming D. Chamfering

The cold forming process in which a hardened tool is pressed against a workpiece (when there is relative motion between the tool and the workpiece) to produce a roughened surface with a regular pattern is A. Strip rolling B. Knurling C. Roll forming D. Chamfering

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Which if these do not belong the the group Hubbing; roll piercing; heading; coining
In which process, a heavy hammer blows the work material to deform its shape? a. Extrusion. b. Forging. c. Bending. d. Drawing.
A circular shape blank will be cut of mm diameter from a strip of mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine The appropriate punch diameter.Blanking force.Blanking force when the blade angle A circular shape blank will be cut of mm diameter from a strip of mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine The appropriate punch diameter.Blanking force.Blanking force when the blade angle is o.
ENT 152 Computer Aided Manufacturing I Milling Worksheet-SHOW ALL WORK A milling operation is to be performed at 100 sfpm at .005 ipt. A 500" diameter, 4 flute HSs end mill is to be used. The operation is a slot .100" deep across the diagonal of a rectangular part 4 inches wide and 6 inches long. The material is 4140 medium carbon steel (BHN-250). Use a specific HP of 1.2 HP/in/min. Calculate: RPM feed (ipm) feed (ipr) Length of cut Cut time MRR a. c. b. f. HP required at the spindle HP required at the motor (assume the drive system is 809% efficient) C. d. h.
The power hammers are used in ___________ operations. a.Deep Drawing. b.Drop Forging. c.Indirect extrusion. d.Turning.
In which of the following forming operations, the workpiece is pulled through a die resulting in reduction of area? a. Wire drawing O b. Rolling O c. Extrusion d. Deep drawing
Q.4- Write (True) or (False) and correct the wrong sentences for the following: 1. Chills are used to increase the heating rate of metal. 2. Motion of job is forward rotary in broaching operation. 3. The upset type of forging makes increment in the diameter of the workpiece. (1-2) Option 1 4. The torch size of (GTAW) process is larger than other (PAW) process. 5. Only two perpendicular components of cutting force act on the tool in case of oblique cutting. 6. The semicentrifugal casting, is used for casting articles of symmetrical shape about vertical axis. 7. In planer machine tool, workpiece remains stationary and tool reciprocates. 8. Boring is performed on the inside diameter of an existing hole. 9. In grinding processes, small grit sizes used to grind soft materials and permit larger material removal rates. 10. Side rake angle on tools is provided to control chip flow.
2) In an orthogonal cutting operation, the cutting tool has a rake angle = 20°. The chip thickness before the cut = 0.25 mm. If the cutting force and thrust force are measured during an orthogonal cutting operation with values, Fc = 1450 N and Ft = 1990 N. The width of the orthogonal cutting operation w = 2.5 mm. the friction angle B is = 79.91° Determine: The Shear Angle The Shear Strain The Shear Strength of the material The Force of Friction
Raw material with an input speed of 3.1 MIS will be rolled to the rolling mill with a plate-shaped cross-section of 155 mm2. Orünün since its cross-section is 96 mm2, what happens to the output speed of the product from the roling mill as mis? Please select one: A.8 B.5 C.11 D.10 E.15
H.W! B A fully work-hardened Aluminium blank of 100mm diameter and 1.2 mm thickness has a constant flow Stress of 350 MPa. It is deep drawn in a constant thickness process to a cylindrical cup of somm mid-wall diameter. The blank-holder force is 30 KN and the friction coefficient is 0.1 a- what is the final height? b-what is the approximate value of the maximum Punch force ? Aus/a-37.5mm, b-57KN
Question 3. Three tool materials are to be compared for the same finish turning operation on a batch of 100 steel parts: high speed steel, cemented carbide, and ceramic. For the high speed steel tool, the 170 Taylor equation parameters are: n= 0.125 and C= 70. The price of the HSS tool is $15.00 and it is estimated that it can be ground and reground 15 times at a cost of $1.50. Tool change time = 3 min. Both carbide and ceramic tools are in insert form and can be held in the same mechanical toolholder. The Taylor equation parameters for the cemented carbide are: n = 0.25 and C = 500; and for the ceramic: n = 0.6 and C = 3,000. The cost per insert for the carbide = $6.00 and for the ceramic = $8.00. Number of cutting edges per insert in both cases = 6. Tool change time = 1.0 min for both tools. Time to change parts = 2.0 min. Feed = 0.25 mm/rev, and depth = 3.0 mm. The cost of machine time = $30/hr. The part dimensions are: diameter = 56.0 mm and length = 290 mm. Setup time for the…
1. A milling operation is to be performed on a ductile cast iron shaft to make slots for assembly. The operation will be done at high speeds for good surface finish. For each of the following tool materials, indicate whether it is a reasonable candidate to use in the operation with a detailed description of why or why not including required alloying element/grade/group etc. where applicable: ) plain carbon steel, (i) high-speed steel, (ii)cemented carbide, (iv) ceramic, and (v) Sintered polycrystalline diamond. After selection of material/materials discuss about ) recommended angles and tool signature (ii) how to held cutting edge, and type of cutting fluids With reasons for each recommended material.