The compound bar is supported by a journal bearing at point E, a thrust bearing at point F and a cable connected between points A and B. The bar is subjected to a point load at point C and a couple moment at point D, as shown in the figure. Determine the support reactions and the force in the cable. Note that the bearings are proper alignment and that point A lies on the xz plane, while point B is on the xy plane. A Free Body Diagram (FBD) is required to receive full points. Neglect the weight of the bar. A 3 ft M=500 lb-ft E 5 ft D F 2 ft 4 ft C P= 1,000lb \ 3 ft y B

The compound bar is supported by a journal bearing at point E, a thrust bearing at point F and a cable connected between points A and B. The bar is subjected to a point load at point C and a couple moment at point D, as shown in the figure. Determine the support reactions and the force in the cable. Note that the bearings are proper alignment and that point A lies on the xz plane, while point B is on the xy plane. A Free Body Diagram (FBD) is required to receive full points. Neglect the weight of the bar. A 3 ft M=500 lb-ft E 5 ft D F 2 ft 4 ft C P= 1,000lb \ 3 ft y B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter4: Shear Forces And Bending Moments

Section: Chapter Questions

Problem 4.5.38P: Beam ABC is supported by a tie rod CD as shown. Two configurations are possible: pin support at A...

See similar textbooks

Similar questions

Find expressions for all support reaction Forces in the plane frame with load 3P applied at C as shown in the figure. Joints A and D are pin supported, and there is a roller support at joint F. The lengths and the properties of the members are shown in the figure. Neglect the weights of all members. Select Rfas the redundant.
Find support reactions at 4 and Band then use the method of joints to find all member forces. Let b = 3 m and P = 80 kN.
The inclined beam represents a ladder with the Following applied loads: the weight (W) of the house painter and the distributed weight (u) of the ladder itself. Find support reactions at A and B: then plot axial force (N), shear (V), and moment (M) diagrams. Label all critical N, V, and M values and also the distance to points where any critical ordmates are zero. Plot N, V, and M diagrams normal to the inclined ladder. Repeat part (a) for the case of the ladder suspended from a pin at B and traveling on a roller support perpendicular to the floor at A.
Consider the plane truss with a pin support at joint 3 and a crtica1 roller support at joint 5 (see figure). (a) Find reactions at support joints 3 and 5. (b) Find axial forces in truss members 11 and 13.
The continuous frame ABCD has a pin support at B: roller supports at A,C, and D; and rigid corner connections at B and C (see figure). Members AB, BC, and CD each have flexural rigidity EL Moment M0acts counterclockwise at B and clockwise at C. Note: Disregard axial deformations in member A Band consider only the effects of bending. Find all reactions of the frame. Find joint rotations al A, B. C, and D. Repeat parts (a) and (b) if both moments M0are counter clockwise.
A 150-lb rigid bar AB. with friction less rollers al each end. is held in the position shown in the figure by a continuous cable CAD. The cable is pinned at C and D and runs over a pulley at A. (a) Find reactions at supports A and B. (b) Find the force in the cable.
A circular bar ACB of a diameter d having a cylindrical hole of length .r and diameter till from A to C is held between rigid supports at A and B. A load P acts at U2from ends A and B. Assume E is constant. (a) Obtain formulas for the reactions R, and RBat supports A and B. respectively, due to the load P (see figure part a). (b) Obtain a formula for the displacement S at the point of load application (see figure part a). (c) For what value of x is RB= (6/5)?,? (See figure part a.) (d) Repeat part (a) if the bar is now rotated to a vertical position, load P is removed, and the bar is hanging under its own weight (assume mass density = p). (See figure part b.) Assume that x = LI2.
A long, slender bar in the shape of a right circular cone with length L and base diameter d hangs vertically under the action of its own weight (see figure). The weight of the cone is W and the modulus of elasticity of the material is E. Derive a formula for the increase S in the length of the bar due to its own weight. (Assume that the angle of taper of the cone is small.)
The nonprismalic cantilever circular bar shown has an internal cylindrical hole of diameter dtl From 0 to x so the net area of the cross section n for segment I is A. Load P is applied at x, and load Ptl is applied at x = L. Assume that E is constant. (a) Find reaction force Ry (b) Find internal axial forces Ntin segments I and 2. (c} Find .v required to obtain axial displacement at joint 3 of
The continuous frame ABC has a pin support at A, roller supports at B and C and a rigid corner connection at B (see figure). Members AB and BC each have flexural rigidity EI. A moment Müacts counterclockwise at A. Note: Disregard axial deformations in member AB and consider only the effects of bending. Find all reactions of the frame. Find joint rotations 6 at A, B, and C. Find the required new length of member AB in terms of L, so that A in part (b) is doubled in size.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
Repeat 1.3-9 but use the method of sections go find member forces in AC and BD.