The diameter and length of single cylinder two stroke gas engine working on constant volume process cycle, are 200 mm and 300 mm respectively with clearance volume 2.78 litres. When engine is running at 135 rpm, the indicated mean effective pressure was 5.2 bar and gas consumption 8.8 m/hr, if Calorific value of Gas used is 16350 KJA m'. Find indicated power developed and indicated thermal efficiency.

The diameter and length of single cylinder two stroke gas engine working on constant volume process cycle, are 200 mm and 300 mm respectively with clearance volume 2.78 litres. When engine is running at 135 rpm, the indicated mean effective pressure was 5.2 bar and gas consumption 8.8 m/hr, if Calorific value of Gas used is 16350 KJA m'. Find indicated power developed and indicated thermal efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the engine speed (in rpm) required for good volumetric efficiency for a square engine with one inlet and one exhaust valve, bore of 0.086 m, inlet air temperature of 327 K, exhaust temperature of 875 K and exhaust valve diameter 31.9 mm. Assume specific heat ratio =1.32, R = 287 J/kg.K, an average inlet flow coefficient 0.37 and an average exhaust flow coefficient 0.47. Select one: a. 7150 b. 7800 c. 5620 d. 8640 e. 9200
02 2. A ix-cylinder, four-stroke cycle, marine oil engine-has cylinder dia méters of 610 mm and a piston troke of 1 25S0 mm. When the engine speod s 2 rev/s it uses 340 kg of fuel oil of calorific value 44 206-Lkg-in one hour. The cooling water amounts to 19200 kg/h, eniering at 15 C and leaving at 63 C The torque transitted at the engine coupling is 108 kN m and the indicaled mean effective pressure is 775 kN/m Determine: ta) the indicated power. ib) the brake power. (c) the percentage of the enerEY Hipplied kg ef fuel lost to the cooling water idi the brake thermal efficiency. jci the brake Hcan eflective pressure: i0 the mechanical efficiency. (g) the brake apecific fuel conumption.
2. An ideal Otto engine operating on the hot air standard with k = 1.34, has a compression ratio of 5. At the beginning of compression the volume is 6 cu ft, the pressure is 13.75 psi and the temp. is 100 °F. During the constant volume heating, 340 BTU are added per cycle. Find a. percent clearance b. T, с. Р, d. Efficiency е. Мер)
2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW Find the Volumetric efficiency
A diesel engine working with cylinder bore of 25 cm and stroke length of 200 mm. the clearance gap beteen TDC and cylinder head is measured as 10 mm. then the compression ratio of the engine will be O b. 22 Oc.21 O d. 200
A power generator with two-cylinder, four-stroke gas engine has a bore of480 mm and a stroke of 585 mm. At 300 rev/min the torque developed is10 kNm. The generator is supplied with a mixture of gas and air in theproportion of 1 to 8 by volume. The estimated volumetric efficiency is 80% and the net calorific values of the fuel is 48.6 MJ/m3. Calculate: 1. the swept volume in m3/min, 2. the volume of mixture induced in m3/min 3. the gas flow to engine m3/min4. the energy supplied by gas5. the brake thermal efficiency
Gas Compressors 14.5 Find the cylinder dimension of a single-cylin der, double acting compressor handling 28.32 Its/revolution of air from 99.975 Kpaa to 723.954 kPaa. Compression and reexpansion are in accordance with p35 = C. Use the conventional volumetric efficiency; c = 5% and L/D =1. Ans. 26.77 x 26.77cm
An Otto engine has a clearance volume of 7%, it produces 300 kW of power in a minute. Find: Compression ratio heat added in kW heat rejected in kW Volume displacement if volume at point 1 is 0.1 m³ mean effective pressure in kPa Thermal efficiency, %
B) The air flow to a four cylinder four-stroke engine is 2.15 m³/min. During a test on the engine the following data were recorded: Bore 10.5cm; stroke 12.5cm; engine speed 1200 rpm, torque 150 N.m, fuel consumption 5.5 kg/hr, calorific value of fuel, 43124 kJ/kg, ambient temperature 1-The brake thermal efficiency. and pressure are 20°C and 1.03 barş. Calculate: 2-The brakes mean effective pressure. 3-The volumetric efficiency.
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
A compressor must operate in a speed range between 0 and 1500 rpm. The friction torque of Coulomb Tc is 10 N. m. What should be the required Tw working torque if the compressor constant is 0.5 N. m. s. What is the power required by the engine that operates this compressor?
Q. A single stage impulse rotor has a blade ring diameter of 57.5 cm and rotates at a speed of 10,000 r.p.m. The nozzles are inclined at 20o to the direction of motion of the blades and the velocity of the issuing steam is 1,050 m/sec. Determine the inlet blade angle. Assume a friction coefficient of the blading equal to 0.85 and that the inlet and outlet angles are equal. Find also: (a) the power developed at the blades for a steam supply of 1,350 kg per hour (b) the diagram efficiency, and (c) the loss of kinetic energy due to blade friction