The electric energy stored in an air-filled parallel-plate capacitor is equal to 5.31 nJ and the volume of the space between the plates is 3.9 x 10-4 m3. Calculate the magnitude of the electric field (in N/C) between the plates of the capacitor.

The electric energy stored in an air-filled parallel-plate capacitor is equal to 5.31 nJ and the volume of the space between the plates is 3.9 x 10-4 m3. Calculate the magnitude of the electric field (in N/C) between the plates of the capacitor.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter8: Capacitance

Section: Chapter Questions

Problem 53P: A parallel-plate capacitor has charge of magnitude 9.00F on each plate and capacitance 3.00F when...

See similar textbooks

Similar questions

The electric field strength between two parallel conducting plates separated by 4.00 cm is 7.50104 V/m. (a) What is the potential difference between the plates? (b) The plate with the lowest potential is taken to be zero volts. What is the potential 1.00 cm from that plate and 3.00 cm from the other?
A 60.0-pF vacuum capacitor has a plate area of 0.010 m2. What is the separation between its plates?
The electric field strength between two parallel conducting plates separated by 4.00 cm is 7.50 104 V/m. (a) What is the potential difference between the plates? (b) The plate with the lowest potential is taken to be at zero volts. What is the potential 1.00 cm from that plate (and 3.00 cm from the other)?
A parallel-plate capacitor with plates of area LW and plate separation t has the region between its plates filled with wedges of two dielectric materials as shown in Figure P25.48. Assume t is much less than both L and W. (a) Determine its capacitance. (b) Should the capacitance be the same if the labels 1 and 2 are interchanged? Demonstrate that your expression does or does not have this property. (c) Show that if 1 and 2 approach equality to a common value , your result becomes the same as the capacitance of a capacitor containing a single dielectric: C = 0LW/t. Figure P25.48
Problems 72, 73, and 74 are grouped. 72. A Figure P26.72 shows a source consisting of two identical parallel disks of radius R. The x axis runs through the center of each disk. Each disk carries an excess charge uniformly distributed on its surface. The disk on the left has a total positive charge Q, and the disk on the right has a total negative charge Q. The distance between the disks is 3R, and point A is 2R from the positively charged disk. Find an expression for the electric potential at point A between the disks on the x axis. Approximate any square roots to three significant figures. FIGURE P26.72 Problems 72, 73, and 74.
A parallel-plate capacitor has charge of magnitude 9.00F on each plate and capacitance 3.00F when there is air between the plates. The plates are separated by 2.00 mm. With the charge on the plates kept constant, a dielectric with =5 . is inserted between the plates, completely filling the volume between the plates, (a) What is the potential difference between the plates of the capacitor, before and after the dielectric has been inserted? (b) What is the electrical field at the point midway between the plates before and after the dielectric is inserted?
A simple and common technique for accelerating electrons is shown in Figure 7.46, where there is a uniform electric field between two plates. Electrons are released, usually from a hot filament, near the negative plate, and there is a small hole in the positive plate that allows the electrons to continue moving, (a) Calculate the acceleration of the electron if the field strength is 2.50104 N/C . (b) Explain why the electron will not be pulled back to the positive plate once it moves through the hole. Figure 7.46 Parallel conducting plates with opposite charges on them create a relatively uniform electric field used to accelerate electrons to the right. Those that go through the hole can be used to make a TV or computer screen glow or to produce X- rays.
(a) How much charge can be placed 011 a capacitor with air between the plates before it breaks down if the area of each plate is 5.00 cm2? (b) What If? Find the maximum charge if polystyrene is used between the plates instead of air.
A capacitor is constructed from two square, metallic plates of sides and separation d. Charges +Q and Q are placed on the plates, and the power supply is then removed. A material of dielectric constant is inserted a distance x into the capacitor as shown in Figure P25.49 (page 690). Assume d is much smaller than x. (a) Find the equivalent capacitance of the device. (b) Calculate the energy stored in the capacitor. (c) Find the direction and magnitude of the force exerted by the plates on the dielectric. (d) Obtain a numerical value for the force when x = /2, assuming = 5.00 cm, d = 2.0 mm, the dielectric is glass ( = 4.50), and the capacitor was charged to 2.00 103 V before the dielectric was inserted. Suggestion: The system can be considered as two capacitors connected in parallel. Figure P25.49
Earth has a net charge that produces an electric field of approximately 150 N/C downward at its surface. (a) What is the magnitude and sign of the excess charge, noting the electric field of a conducting sphere is equivalent to a point charge at its center? (b) What acceleration will the field produce on a free electron near Earth’s surface? (c) What mass object with a single extra electron will have its weight supported by this field?
A simple and common technique for accelerating electrons is shown in Figure 18.55, where there is a uniform electric field between two plates. Electrons are released, usually from a hot filament, near the negative plate, and there is a small hole in the positive plate that allows the electrons to continue moving. (a) Calculate the acceleration of the electorn if the field strength is 2.50104 N/C. (b) Explain why the electron will not be pulled back to the positive plate once it moves through the hole.
Oppositely charged parallel plates are separated by 5.33 mm. A potential difference of 600. V exists between the plates. (a) What is the magnitude of the electric field between the plates? (b) What is the magnitude of the force on an electron between the plates? (c) How much work must be done on the electron to move it to the negative plate if it is initially positioned 2.90 mm from the positive plate?