The engineers of the telecommunication company tested the link between the sender and the receiver for a multimedia application, and found Q(x)=0.158 for the 16-QAM digital communication system. Can this system transmit data free from ISI problem with 10 kbps speed over a noisy channel of 5 kHz? Prove mathematically.

The engineers of the telecommunication company tested the link between the sender and the receiver for a multimedia application, and found Q(x)=0.158 for the 16-QAM digital communication system. Can this system transmit data free from ISI problem with 10 kbps speed over a noisy channel of 5 kHz? Prove mathematically.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

Modulation index for AM system is 0.35. what will be the efficiency of the AM system? Also, what is the theoritical maximum efficiency of AM system?
Why SSB is preferred for transmission of good quality signal
Explain difference between SNR and BER. Subject is Communication system
3. Some GPS receivers use 1 bit ADCS (Analog-to-digital Converters) to sample and quantize the signal i.e. the output of the ADC is simply 2 quantization levels: -1 or +1. This is typically done to save on power. (a) What is the quantization SNR? How does it compare to typical thermal noise SNR of a GPS signal before correlating with the CDMA code? (b) Justify, how come it is possible to sample the signal using a single bit and still get good performance.
Which of the following is not an effect caused by multipath in radio channel? a) Rapid changes in signal strength b) Random frequency modulation c) Power of base station d) Time dispersion
Design a 3x8 decoder by using 1x2 DEMUXE..
Explain how adaptive modulation works in communications systems using an illustration?
solve all questions on Keyboard and all parts or will dislike answer Even if the received modulated signal is distorted, it is relatively easier to decode when A) using Analog modulation B) using Digital modulation TDMA is more flexible than FDMA in terms of resource allocation A) true B) False Fill in the blanks choosing from one of the options shown below: Transmitting the same signal on separate frequencies is also known as ……………….. and using two or more antennas for reception is also known as …………… a. (Frequency multiplexing , antenna multiplexing) b. (Frequency diversity , antenna diversity ) c. (Spatial diversity , spatial multiplexing) d) None of above Which of the following is secure by design, i.e. security is built into the design itself. b. CDMA a. FDMA c. TDMA Point to point microwave links are an attractive way of setting up wireless backhaul links A) TRUE B) FALSE
We want to design a digital circuit that converts Gray code (ABC) to Binary code (xyz). Set up a 8-to- 1 line multiplexer so that the output gives y as a function of ABC. "A" is given to the most significant bit of the control inputs of the multiplexer. "C" is given to the least significant bit of the control inputs of the multiplexer.
Why modulation is necessary in communication system? Explain with at least three advantages of the importance of modulation in communication system?
Two M-QAM modulation schemes, 16-QAM and 64-QAM, having equal error performance (I.e same value of Pbe). SNR-13 dB 16-QAM system. Calculate the E/N, in 64-QAM system. Compare the results. What are the maximum transmission rate (free from ISI problem) in both modulation schemes? Assume B=20 kHz.
Q4/ Why the performance of multimode graded index is better than multimode step index? Q5/ Design fiber optics communication system with analogue input and then measure the performance of the three types of fiber optics configurations. After that, answer the following questions: 1. Which configuration is the better? Comment! 2. Which parameters that improve the performance of multimode step index? Comment! 3. Which parameters that improve the performance of multimode graded index? Comment! 4. Which parameters that improve the performance of single mode step index? Comment! 5. If we need to increase the fiber length from 1 km to 15 km. which configuration is used? Comment!