The field winding of a.d.c. machine takes a steady current of 10A when connected to a d.c. source of 230 volts.On, switching the voltage to the field, it is observed that it takes O.3 second to reach 5 A. (i) Find the value of inductance of the field winding. (ii) Find also the time for the current to fall to 30% of the final steady value if the field terminals are short - circuited.

The field winding of a.d.c. machine takes a steady current of 10A when connected to a d.c. source of 230 volts.On, switching the voltage to the field, it is observed that it takes O.3 second to reach 5 A. (i) Find the value of inductance of the field winding. (ii) Find also the time for the current to fall to 30% of the final steady value if the field terminals are short - circuited.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q9 / What are the function of brushes , pole and commutator in DC machine
10. A potential difference of 250 V is applied to a field winding at 15-C and the current is 5 A. What will be the temperature of the winding when current has fallen to 3.91 A applied voltage being constant. Assume temperature coefficient at 15'C is equal to 1/254.5 per °C
A magnetic ring has reluctance of 1.675 × 10⁰ AT weber. The flux to be produced by the coil is 800 x 10 webers, then the AT required for the m.m.f. will be
An air core toroidal coil has 120 turns, the length is 12 cm and 12 sq. cm in area What is the current required to set up a flux of 1.2x10° weber. What is the current?
A toroidal coil, with a circular cross-sectional area of 0.2m2. The coil inductance is 0.28H. The coil has 500 turns. How much current should flow in the coil to get a flux linkage of 498? a. 498.000 A b. 140.000 A c. 1778.571 A d. 249000.000 A e. 889285.714 A
a) A sinewave is having a frequency of 100 Hz and instantaneous value of 150 Volts at 1.4 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=200 Volts, Time period is 5 milli seconds and 0 =40 degrees. Vp t = 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms = b) Angular frequency =
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.2 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 5 milli seconds and 0 =50 degrees. Vp i= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms b) Angular frequency %3D
Derive the expression for equivalent inductance for the following: 1. When two coils connected in series and the flux is adding. 2. When coils are connected in series but flux is opposing. 3. When coils connected in parallel and flux are adding. 4. When coils are connected in parallel but flux are differential coupled
A coil that con sists of 450 windings is wound aroundabakelite ring. The mean diameter of the ring is 100 mm and the diameter of the bakelite core is 20 mm. The currentthrough the coil is 3 A. Determine: 1.1 a) the field stren gth b) the flux den sity c) the total flux A ringhas two halves. The onehalf is made from Cast iron, while the other is made from Cast steel. The two halves are held 1 mm apart with the aid of a paper disc. The cross-section al area and mean circumference of the ringis 345 mm? and0.6 m respectively. Therelative permeability of cast iron is 2400, while that of cast steel is 600. The ring has a coil with 200 win dings. The currentflow through the coil causes a flux den sity of 0.48T. 1.2 Calculate the: a) mmi b) currentflow Ignore the effects of fringing andleakage.
Probl The rectangular coil in the figure below is in a field B = 0.01a,T. a. Find the torque about the z axis when the coil is in the position shown and carries a current of 10 A b. Find the torque if the coil turns through 90°7 0.2m & 0.2m 1-10A
Draw and explain a typical power curve for a wind turbine and write the definition of the four important terms that are shown in the power curve
DC and AC subject: The wire shown is moving in the presence of a magnetic field. With the information given in the figure, determine the magnitude and direction of the induced voltage in the wire. Show the full solution clearly.