The figure below is a spur gear train drive and gear 2 is the inlet of the gear train. It transfers 12 kw of power at 1200 rpm. Gear 3 and 4 have 60 and 20 teeth respectively and are made with 20° pressure and full-depth teeth. The desired speed for the output shaft is 32 rpm. a. Find the minimum number tooth on gear 2 to obtain 32 rpm at the output and confirm its validation for interference-free power transfer. b. Find the speed ratio at each gear set using the results obtained at "a"(above). c. Determine the rotational speed of each gear (n2, n3, n4, and ns) using the results obtained at "a"(above). d. Find the torque of each shaft (Tin, Te, Tout) assuming that there is no frictional loss during the power transfer. e. Determine the radial, tangential and total forces transmitted at the last gear set assuming a module as m=4 mm, and draw the free body diagram of gear 4 showing the forces and torques. ,75, 100 2007 In 2 5 Out D 3, C 3

The figure below is a spur gear train drive and gear 2 is the inlet of the gear train. It transfers 12 kw of power at 1200 rpm. Gear 3 and 4 have 60 and 20 teeth respectively and are made with 20° pressure and full-depth teeth. The desired speed for the output shaft is 32 rpm. a. Find the minimum number tooth on gear 2 to obtain 32 rpm at the output and confirm its validation for interference-free power transfer. b. Find the speed ratio at each gear set using the results obtained at "a"(above). c. Determine the rotational speed of each gear (n2, n3, n4, and ns) using the results obtained at "a"(above). d. Find the torque of each shaft (Tin, Te, Tout) assuming that there is no frictional loss during the power transfer. e. Determine the radial, tangential and total forces transmitted at the last gear set assuming a module as m=4 mm, and draw the free body diagram of gear 4 showing the forces and torques. ,75, 100 2007 In 2 5 Out D 3, C 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The figure below is a spur gear train drive and gear 2 is the inlet of the gear train. It transfers 12 kw of power at 1200 rpm. Gear 3 and 4 have 60 and 20 teeth respectively and are made with 20° pressure and full-depth teeth. The desired speed for the output shaft is 32 rpm. a. Find the minimum number tooth on gear 2 to obtain 32 rpm at the output and confirm its validation for interference-free power transfer. b. Find the speed ratio at each gear set using the results obtained at "a"(above). c. Determine the rotational speed of each gear (n2, n3, n4, and n5) using the results obtained at "a"(above). d. Find the torque of each shaft (Tin, Te, Tout) assuming that there is no frictional loss during the power transfer. e. Determine the radial, tangential and total forces transmitted at the last gear set assuming a module as m=4 mm, and draw the free body diagram of gear 4 showing the forces and torques. 75, 100 2007 In Out 4
Find the diameter of each gear using one simple gear train with 4 gears that work as a speed reducer with a ratio of 5:1 Input of 100 rpm, Output of 20 rpm. Consider number of teeth as: N1=20 N2=40 N3=80 N4=100 Use module of 2
For the simple gear train shown, calculate the torque ratio (VR). 130 rpm Wout Input Output Teeth N = 20 N = 45 %3D N = 95 %D
Q1/ Two involute gears of 20° pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is 2. If the pitch expressed in module is 5 mm and the pitch line speed is 1.2 m/s, assuming addendum as standard and equal to one module, find : 1. The angle turned through by pinion when one pair of teeth is in mesh ; and 2. The maximum velocity of sliding.
Q2/ Two mating involute spur gears of 20* pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on cach wheel is such that the path of approach and the path of recess on cach side are half the maximum possible length each, find: i) the addendum for pinion and gear wheel, ii) the length of arc of contact, iii)the maximum velocity of sliding during approach and recess. Assume pinion to be driver.
2. The following data is for the gear train shown in the figure: Given: N2 = 30t, N3 = 35t, N4 = 55t, N5 = 40t, N6 = 50t, N7 = 40t %3D w2 = 30 rpm ccw, warm = 20 rpm cw, Input torque on gear 2 is 1200 lbf.in Determine the following: a. Angular velocity of the sun gear. b. The gear ratio R required to determine the angular velocity of gear 6. c. The angular velocity of gear 6. d. The angular velocity of gear 7. e. Output torque on gear 7. Be careful with your units. Arm 6 ... 7
Q: Two involute gears having module 3 mm and pressure angle 20° mesh externally to give a velocity ratio of 3. For this mechanism, the pinion runs at 75 rpm and addendum is equal to one module.For these condetions compute: 1- The number of teeth on each gear so that interference is just avoided. 2- The length of path and arc of contact. 3- The number of pairs of teeth in contact. 4- The maximum value of sliding velocity. 5- If the transmitted power is 5 kW, what is the applied torque on pinion and wheel.
Consider the gear train in the following figure. Assume the angular velocity of driving gear is Win = 1000 rpm. Find the angular velocity of driven gear (@out). Driving Gear 12 Tooth Linked by Shared Axle Driven Gear 60 Tooth 60 Tooth
In the planetary gear train shown in below figure, Gear A is the driver and gears B and D are compounded.Gears E and C are internal gears with C as the fixed gear.Number of teeth on gears are TA-20;TB-60; Tc-140;TD-40;,TG-120. If the drive gears rotates at 720rpm CCW when seen from the right, find out the speed at which driven gear rotates C140 120 Output D 40 60 20 Input
ASAP
A pinion having 40 teeth is meshing with a spur gear having 80 teeth. The profile of the gear is involute. The module of the gears is 12 mm and pressure angle is 20 degree. The addendum of the gears is 10 mm. Find the length of path of contact, arc of contact and the contact ratio.
The following data is for two meshing gears Velocity ratio=0.5 Module =5 mm, Pressure angle =20° Centre distance = 250 mm Determine the number of teeth and the base circle radius of the gear wheel.