VPThe figure (not drawn to scale) shows a metallic cylindricalcolumn submitted to a combined load: bending and torsion. Thecolumn contains an hemispherical groove of radius r, located at adistance L from the point of application of the loads.You are giventhe column diameter D = 68 mm,the groove radius r = 6 mm,the distance L= 200 mm,the bending load P=5 kN,and the torque T = 600 N.m.The material data areYoung's modulus E = 122 GPaShear Modulus G = 55 GPaPoisson's ratio v = 0.1and Yield strength oy = 380 MPa.a) Write a numbered list of the calculation steps required toobtain the factor of safety in yielding based on the maximumdistortion energy (Von Mises) criterion.Enter your answer in the box below

Answered: Image /qna-images/answer/1cab85f0-9904-4cdc-8aba-7ece8154ae87.jpg

The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads.

The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.18P: A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed...

See similar textbooks

Related questions

Q: When a tree branch bends, it can be assumed that acts as a spring, i.e there is a restoring force…

A: Given : To find : mass of the monkeys

Q: A thin cylindrical rod of uniform mass m and length L is suspended from the ends by two massless…

A: Given : To find : Find the motion's equation

Q: In the truss system shown, Calculate all internal forces in 3 m each member by method of joints.…

Q: The pulley system shown in Figure Q1c lifts a mass, m, of 550 kg. Calculate the force FA necessary…

Q: 5.39 The overhanging beam carries a uniformly distributed load totaling 8 W and (Wo concentrated…

Q: 5.40 The beam carries a concentrated load W and a uniformly distributed load that totals 4W.…

Q: a) Draw FBD of truss ABCD and determine support forces at A and C. b) Draw FBD of pin at C.…

A: According to Bartleby guidelines, we are allowed to solve only the first 3 sub-part of a single…

Q: A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques…

A: given; stress for steel (τst)=87MPastress for aluminium (τAl)=59MPadiameter of aluminium…

Q: TRUE OR FALSE Shear stress due to a torque is maximum at the surface of a shaft. TRUE OR FALSE…

A: ONLY 3 SUB - QUESTIONS CAN BE SOLVED AT A TIME. FOR SOLUTIONS OF OTHER QUESTIONS , KINDLY UPLOAD THE…

Q: A mass weighing 20 Ib. stretches one spring 5 times as much as it stretches a second spring. The…

A: Given data Mass attached = 20 lbOne spring stretches 5 times as much as the second spring.The total…

Q: A thin-film electrical heater dissipating 2000 W/m? is sandwiched between two 25 mm thick plates…

A: Given: Total heat flux dissipating from the electrical heater→qT=2000 W/m2 Hence heat flux…

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

Q: Problem (1) Consider the shown plane truss. Take: EA= 10' lb for all members, P = 1,000 lb, and L =…

A: Given : To find : a. Assemble the reduced stiffness matrix of the truss. b. Calculate the…

Q: TRUE OR FALSE Shear stress due to a torque is maximum at the surface of a shaft. TRUE OR FALSE…

Q: 2. Determine the force in each member of the truss in Fig. Q2 and state if the members are in…

Q: Two mating spur gears with module pitch 6.5 mm have 19 and 47 teeth of 20° pressure angle and 6.5 mm…

A: Answer: ◆ The number of pairs of teeth in contact: 1.64375 ◆ The angle turned through by the larger…

Q: Consider a two degree of freedom bar elements as shown in figure. Using finite element method to…

A: formulate the equilibrium equation for the given system using finite element method.

Q: Complete the schematic below to provide for the following: 1. Cylinders extend and retract together.…

A: Given : To find : Complete the diagram

Q: KMS systems can be used in every firm, but how can they be used yet not relied on by everyone?

A: Given question: KMS systems can be used in every firm but how can they be used yet not relied on by…

Q: maximum force P t

A: To find Maximum force P

Q: A ball is thrown straight up from a roof top with an initial speed of 15 m/s. Another ball is thrown…

Q: What should the operator of a milling machine do to make the machine a safe piece of equipment?

Q: Assume the stabilizer of an airplane is a flat plate. If the transition /critical RN 750,000, what…

Q: -The blockage of the capillary tube may be due to dirt or the presence of moisture Inside the icing…

A: The capillary tube is the simplest of the refrigerant controls. It is the most popular method for…

Q: A pulley system is carrying a 90 kg object as shown in Figure Q5. The total weight and the radius of…

Q: w = wo sin (7x) Wo A L if wo-(acute angle between the hands of a clock at 7:30 A.M.) Ib/ft and…

Q: b) Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid…

Q: EL:5.50m EL:4.00m Tank-A EL:1.00m- A siphon consist a 15 cm diameter of pipe which is used to empty…

A: To calculate the required result in this question, we must apply the Bernoulli's equation which is…

Q: 9. The nozzles of the impulse stage of a turbine receive steam at 15 bar and 300 °C and discharge it…

Q: 5.41 The inverted T-beam supports three concentrated loads as shown in the fig- ure. Find the…

Q: Saturated vapor of Refrigerant 134a contained in in a piston-cylinder device undergoes an isothermal…

Q: A pulley system is carrying a 90 kg object as shown in Figure Q5. The total weight and the radius of…

Q: A Carnot engine takes 2 kJ of heat from a reservoir at 500 K, does some work and discards some heat…

Q: Problem 1. Determine angles a, b, and c shown in the Figure 1. The vertical lines are, of course,…

A: As per our guidelines we are supposed to solve only one question of multiple questions are asked.…

Q: 4. The mine car and its contents have a total mass of 6000 kg and a centre of gravity at G. If the…

Q: Find the center distance in (cm) of 4 direct contact rolling cylinders. Cylinders A-D have a speed…

Q: Fill in the blanks: Find the distance in (inches) of the shafts if the small cylinder is 88 inches…

Q: Provide a complete given and computation. Include all the decimals. There are received 68,000 kg/h…

A: Heater pressure = 96Mpa Heater recives = 15400 kg/h Condenser pressure = 0.07 Mpa At 96 Mpa S1=…

Q: Determine the horizontal and vertical components of reaction at the pin A and the reaction of the…

Q: Given the Statically Determinate Propped Beam as shown below with internal hinged at Point B. The…

A: (a) Draw the free-body diagram of the beam.

Q: A 4kg ball and 3kg ball move on a smooth plane along a straight path with speeds equivalent to 6m/s…

Q: Figure Q1a shows two cables attached to a half-ring anchor point as shown in Figure Q1a. Force F1…

A: Given:F1=2170 NF2=1240 NR=3100 N

Q: Recall the two coupled masses undergoing linear oscillations in Example 8, p.22-25. Solve a simple…

A: For solution refer below images.

Q: 1) Band brake absorb 7.5 Hp at 300 rpm. The maximum pressure of the lining and the drum is 130 psi.…

Q: Problem 2: A circular rod tapers in diameter from 50 mm from one end to 20 mmon theother end for a…

Q: A circular plate 3 m diameter is Immersed in water in such a way that its greatest and least depth…

A: We know that a circular plate with a diameter of 3 m is immersed in water with a maximum depth of 4…

Q: A thermometer reading 75 °F is taken out where the temperature is 20 °F. The reading is 30 °F 4 min…

Q: Select the correct answer. 1- Which of the following disciplines provides study of relative motion…

A: Disclaimer: “Since you have asked multiple questions, we will solve the first question for you. If…

Q: ) aluminum for airplane bodies. b) nickel chromium for heating elements

A: we will discuss why aluminum is preferred in aircraft

Q: S. The cost of producing a small transistor radio set consists of P 230.00 for labor and P 370.00…

A: The number of sets must be produced per month to break-even is 7143 sets.

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

VP
The figure (not drawn to scale) shows a metallic cylindrical
column submitted to a combined load: bending and torsion. The
column contains an hemispherical groove of radius r, located at a
distance L from the point of application of the loads.
You are given
the column diameter D = 68 mm,
the groove radius r = 6 mm,
the distance L= 200 mm,
the bending load P=5 kN,
and the torque T = 600 N.m.
The material data are
Young's modulus E = 122 GPa
Shear Modulus G = 55 GPa
Poisson's ratio v = 0.1
and Yield strength oy = 380 MPa.
a) Write a numbered list of the calculation steps required to
obtain the factor of safety in yielding based on the maximum
distortion energy (Von Mises) criterion.
Enter your answer in the box below

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A round bar ABC of length 2L (see figure) rotates about an axis through the midpoint C with constant angular speed w (radians per second). The material of the bar has weight density y. (a) Derive a formula for the tensile stress a’ in the bar as a function of the distance x from the midpoint C. (b) What is the maximum tensile stress a max?
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A bar ABC revolves in a horizontal plane about a vertical axis at the midpoint C (see figure). The bar, which has a length 2L and crass-sectional area A, revolves at constant angular speed at. Each half of the bar (AC and BC) has a weight W, and supports a weight W2at its end. Derive the following formula for the elongation of one-half of the bar (that is. the elongation of either AC ar BC). =L223gEA(w1+3w2) in which E is t he modulus of elasticity of the material of the bar and g is the acceleration of gravity.
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
Solve the preceding problem for the following data: b = 6 in., b = 10 in, L = 110 ft, tan a = 1/3, and q = 325 lb/ft.
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
Solve the preceding problem for the following data:P = 160 kN,JV = 200 tN,L = 2 m,b = 95 mm, h = 300 mm, and d = 200 mm
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
A tubular bar with outside diameterd2= 4.0 in, is twisted by torques T = 70,0 kip-in. (see figure). Under the action of these torques, the maximum tensile stress in the bar is found to be 6400 psi. Determine the inside diameter rtf of the bar. If the bar has length L = 48.0 in. and is made of aluminum with shear modulus G = 4,0 × 106 psi, what is the angle of twist d (in degrees) between the ends of the bar? (c) Determine the maximum shear strain y (in radians)?
Solve the preceding problem if the cube is granite (E = 80 GPa, v = 0.25) with dimensions E = 89 mm and compressive strains E = 690 X l0-6 and = = 255 X 10-6. For part (c) of Problem 7.6-5. find the maximum value of cr when the change in volume must be limited to 0.11%. For part. find the required value of when the strain energy must be 33 J.
A nonprismatic bar ABC with a solid circular cross section is loaded by distributed torques (sec figure). The intensity of the torques, that is, the torque per unit distance, is denoted t(x) and varies linearly from zero at A to a maximum value T0/L at B. Segment BC has linearly distributed torque of intensity r(x) = T0/3L of opposite sign to that applied along AB. Also, the polar moment of inertia of AB is twice that of BC and the shear modulus of elasticity of the material is G. Find the reaction torque RA. Find internal torsional moments T(x) in segments AB and BC. Find the rotation t0 Find the maximum shear stress tmaxand its location along the bar, Draw the torsional moment diagram (TMD:T(x),0 < x < L).