the flow rate in each pipe (+ is out and - is into the reservoir) Assume hA = 60 m, hg = 90 m, hc = 20 m, l1 = 150 m, l2 = 150 m, and l3 = 300 m. Elevation - ha Elevation = h, Elevation = he D= 0.10 m = 0.015 D,= 0.08 m 0.08 m

the flow rate in each pipe (+ is out and - is into the reservoir) Assume hA = 60 m, hg = 90 m, hc = 20 m, l1 = 150 m, l2 = 150 m, and l3 = 300 m. Elevation - ha Elevation = h, Elevation = he D= 0.10 m = 0.015 D,= 0.08 m 0.08 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q4) The three water-filled tanks shown in Figure below are connected by pipes as indicated. If minor losses are neglected, determine the flow rate in each pipe. Elevation = 60 m Elevation = 20 m Elevation = 0 D = 0.10 m l = 200 m f = 0.015 %3D D = 0.08 m l = 200 m f = 0.020 D = 0.08 m l = 400 m f = 0.020 %3D
Q2: As shown in figure (2), when the pump develops (7.5m) of head, and the velocity of flow through the pipe No.3 is 2 m/sec. Neglecting the minor losses, find the flow in pipe No.1 and pipe No.2, and the elevation of pipe No.2 at discharge point. The pipe characteristics are as follows Pipe 1 2 3 (f) for all pipes = 0.03. EL.30m 4 Water ( P L(m) 1200 600 1200 D(mm) 600 600 600 EL.: ? Figure (2)
A pumping station wet well operates between 540- and 550-ft elevation. The pump curve is deϐined by the following points: 80 ft at zero ϐlow, 78 ft at 200 gpm, 65 ft at 800 gpm, and 50 ft at 1200 gpm. The pump discharge contains an equivalent of 50 ft of 6-in. pipe. The discharge pipe is 120-ft long and terminates at a splitter box, elevation 570. Using C=100, plot the pump curve and the corrected pump curve. Plot the pump discharge curves at each wet well elevation and for C=100 and C=140. What is the pump ϐlow at the low and high wet well elevations for newand old pipe?
Question 3 Consider 2 which shows a pipe system connecting two reservoirs. The pipe diameter changes at point B as shown in the image A 10 cm 23 m NOT TO SCALE Figure 2: 9 m 6 cm с 3 m 1. Describe what is referred to by the hydraulic gradient line and the energy gradient line. What is the difference between the two levels? In what scenario will the energy and hydraulic grade lines coincide? 2. Calculate the velocities in the two segments of the pipe. Take into account the friction losses through the pipe, entry loss to the pipe and the shock contraction losses at B. Take the pipe friction factor as 0.005 and the coefficient of contraction at B as 0.6. 3. Draw the energy gradient line and the hydraulic gradient line for the system.
4. FLUID FLOW 1. The figure below shows a water tank with piping system for a small manufacturing plant. If water flows through the system ((A) at 40 L/s, what would be the pressure at point B? The water has a density of 998 kg per cubic meter and viscosity of 0.8 centipoise. measures 0.04089 m and 0.04826 m in inside and outside diameter, respectively. The tank is exposed to the atmosphere The 1.5 inches (nominal) wrought iron pipe Given: Q= 40L/s = 0.040 m/s p= 998 kg/m H=0.8 centipoise 0.001P-s = 0.08 P-S Reg'd: Pressure at B. = ? 1 cp i.d. = 0.04089 m o.d. = 0.04826 m length of pipe = 110 m
Q2 = 10 liter/s DI =? Water D3 = 65mm Tank base area=1 m² rigure 5 (b) A water reservoir (p = 998 kg/m³ ) is being filled through section 1 at Vị = 3 m/s and through section 2 at Q. = 10 litre/s and exit at section 3 at 6.5 m/s which is shown in Figure 5. Calculate the diameter at section 1 so that : i. h is constant, ii. h decrease at 6 mm/s h is constant and section 2 is closed iii. of
Q.4. In the system shown in figure, the water flow rate ,Q= 0.5 m3/s and pressure P=20 kPa are required at the point C. Calculate flow directions and flow rates in the pipes and power of the pump required in the system. Draw the energy lines in the system. Note: Neglect the local losses and take f=0.02 in the analysis. B ZA-20 m ZB=40 m 3 zc=4 m ZD=0 m A 2 Li=95 m, L2=120 m, L3=100 m 1 L2= 125m Pump D= 30 cm D k=0.046 mm
Q2- Water density =1000 kg/m and viscosity is 0.001 Ns/m², is pumped between two reservoirs at 0.2m/s through a 400 m of 8 cm diameter Cast Iron pipe and several minor losses as shown in the figure. Compute the pump power required in kW. Use the last one digit of your ID number for Z1 level in meter. Screwed Z2= 50 m regular 90° elbow Sharp exit Z;= ID m Sharp entrance Half-open gate valve `bend radius Pump Open globe valve 8 cm diameter
SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m2/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). HI 300 m H2 datum A = SN/1000 L = 100 x SN (m) D 0.3 m Please solve these question my sn number 31
Water flows inside a solid cylindrical pipe, which narrows as it goes up to a height h (see diagram below). The lower horizontal section has circular cross-sectional diameter d, whereas the upper horizontal section has diameter d/2. Let us denote A to be a point at the lower horizontal section and B to be a point at the upper horizontal section. The flow speed at A and B is uд and u, respectively. The pressure at A and B is PA and PB, respectively. РА UA Oom Ja d d/21 1 UB h (a) Assuming water to be incompressible, show that the flow speed at B is four times the flow speed at A. (b) Use Bernoulli's equation to find the drop in the water pressure from A to B. Express the result in terms of h, uд, the density of water p, and the acceleration of gravity g. (c) Above certain critical height h, vapour bubbles start to appear at the top horizontal section, which hinders water flow through the pipe. Explain why this happens.
The water of a 14’ × 48’ metal frame pool can drain from the pool through an opening at the side of the pool. The opening is about h = 1.05 m below the water level. The capacity of the pool is V = 3740 gallons, the pool can be drained in t = 10.2 mins. P0 is the pressure of the atmosphere. ρ is the density of the water. a. Write the Bernoulli’s equation of the water at the top of the pool in terms of P0, ρ, h. Assuming the opening is the origin. b. Write the Bernoulli’s equation of the water at the opening of the pool in terms of P0, ρ, h and v, where v is the speed at which the water leaves the opening. Assuming the opening is the origin. c. Express v2 in terms of g and h. d. Calculate the numerical value of v in meters per second. e. Express the flow rate of the water in terms of V and t. f. Express the cross-sectional area of the opening, A, in terms of V, v and t. g. Calculate the numerical value of A in cm2
2. Oil with a S.G. pf 0.82 is flowing in a pipe under the condition below (see figure). If the total head loss from point 1 to point 2 is 3 ft, find the pressure at point 2 in PSI. Note: cfs = cubic ft per sec Point 1 D₁ - 6 km P₁-65 pal 0 Q-2.08 efs Q-2.08 efs Point 2 D₂ - 9 in 10.70 ft 4.00 ft Reference datum