The force P has a magnitude of 300 Nand is applied at the end C of the rodABC, as shown. Assuming a=35° andB=50°, replace P withCBP(a) an equivalent force-couple system at300 mmВ,(b) an equivalent system formed by twoparallel forces applied at A and B.A200 mm

Answered: Image /qna-images/answer/037c2f0d-e49a-425b-b0d3-1833c4ead269.jpg

The force P has a magnitude of 300 N and is applied at the end C of the rod ABC, as shown. Assuming a=35° and B=50°, replace P with (a) an equivalent force-couple system at B, (b) an equivalent system formed by two parallel forces applied at A and B.

The force P has a magnitude of 300 N and is applied at the end C of the rod ABC, as shown. Assuming a=35° and B=50°, replace P with (a) an equivalent force-couple system at B, (b) an equivalent system formed by two parallel forces applied at A and B.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter2: Basic Operations With Force Systems

Section: Chapter Questions

Problem 2.80P: The figure shows one-half of a universal coupling known as the Hooke's joint. The coupling is acted...

See similar textbooks

Related questions

Q: 80 mm 300 mm D 240 mm 80 mm B 240 mm C The rectangular plate is supported by the brackets at A and B…

Q: The magnitude of the force P is 935 N. Determine the magnitude of the moment (Nm) of P about

Q: Part A: The cell tower in Figure a is guyed by three cables as shown. If the tension in cable AC is…

Q: 2/58/During a ground test with both main and tail rotors n atendy operation, a 400-N nerodynamic…

Q: The hydraulic cylinder BD exerts on member ABC a force P directed along line BD. Knowing that P must…

A: Draw the free body diagram showing the forces along ABC.

Q: The rectangular plate is supported by the brackets at A and B and by a wire CD. Knowing that the…

Q: 3- A prybar is used to remove a nail as shown. Determine the moment of the 60-lb force about the…

A: From the given information,

Q: Knowing that the forces P and Q are equivalent to a single force R that passes through point A,…

Q: A cube of side length a is acted upon by a force F as shown. Determine the magnitude of the moment…

Q: A mechanic uses a crowfoot wrench to loosen a bolt at C. The mechanic holds the socket wrench handle…

A: Given data

Q: Slider P can move along rod OA. An elastic cord PC is attached to the slider and to the vertical…

A: Given data To determine a) The angle between the elastic cord and the rod OA b) The projection on…

Q: A machine component is subjected to the forces shown, each of which is parallel to one of the…

A: For equivalence force at A ΣF = RARA = -(240 N) j^ -(125 N) k^-(300 N) i^ +(150 N)k^RA = -(300 N)i^…

Q: The tension in cable AB is 17 kN. Replace this force as it acts on point A by an equivalent…

Q: 3.1 Determine which of the force systems in (b) through (f) are equivalent to the force-couple…

Q: 1) Replace the 800-lb force acting at point A by a force- couple system at (a) point O and (b) point…

Q: The plate shown has seven (7) identical sides that are 300 mm long. Find where the line of action of…

Q: Difficult Problem: If magnitude of MA is 1200 kN – m and the distance between A and B is 3 m, what…

Q: The force P has a magnitude of 250 N and is applied at the end C of a 500-mm rod AC attached to a…

Q: A mechanic uses a crowfoot wrench to loosen a bolt at C . The mechanic holds the socket wrench…

A: Given data Moment at CMC= (360 lb·in)i Force at C = -(8 lb)i + (4 lb) k To determine the forces…

Q: Determine (a) the required tension in cable AC, knowing that the resultant of the three forces…

A: In given figure: At the point c three force is exerted 200 N ,300N , and force of boom BC ,…

Q: The cable stays AB and AD help support pole AC. Knowing that the tension is 120 lb in AB and 40 lb…

A: Given data as per the question Tension in AB =120 lb Tension in AD =40 lb considering FBD of the…

Q: Knowing that the tension is 510 lb in cable AB and 425 lb in cable AC, determine the inagnitude and…

A: Given information: Tension in the cables (T1) = 510 lb; T2 = 425 lb From the given figure we can…

Q: A 160-lb force P is applied at point A of a structural member.Replace P with (a) an equivalent…

A: Given data Load acting on point A, P = 160 lb. Part (a) Draw the diagram for replacing P as shown…

Q: A crate of mass 80 kg is held in the position shown. Determine (a) the moment produced by the weight…

A: Part A) Now determine the moment about point E due to the crate load.

Q: A crate of mass 80 kg is held in the position shown. Determine (a) the moment produced by the weight…

Q: 1. During a ground test with both main and tail rotors in steady operation, a 400 N aerodynamic…

A: Given Force, F = 400 N Distance, d = 6 m Find Force couple system, C

Q: The 500-N weight is supported by two cables, the cable forces being F1 and F2 · Knowing that the…

Q: A disabled car is pulled by means of two ropes acting in the same plane. The tension in rope AB is 3…

A: Given: The magnitude of the tension in rope AB is TAB=3 kN. The magnitude of the resultant force is…

Q: ne frame ACD is hinged at A and D and is supported by a cable that passes through a ring at B and is…

Q: A hexagonal plate is acted upon by the force P and the couple shown. Determine the magnitude and the…

A: Given Applied load = 300 N To find Magnitude of P Angle of P

Q: The bracket, which is fastened to a wall by anchor bolts at A and B, is loaded by the force P = 140…

A: First part of the problem will be solved by determining the resultant of the given system of forces.…

Q: While using a pencil sharpener, a student applies the forces and couple shown. (a) Determine the…

A: Equilibrium of forces: ΣF = 0 ; B + C - R = 0 ΣFx = 0 Bx + Cx = 2.6…

Q: The 0.61x 1.00-m lid ABCD of a storage bin is hinged alongside AB and is held open by looping cord…

A: To findMA & TCETo determine the value of Z Z=0.612-0.112Z=0.60 m

Q: Q3) The rectangular plate is supported by the brackets at A and B and by a wire CD. Knowing that the…

A: Given Data: The tension in the wire is, T=200 N.

Q: Replace the wrench shown with an equivalent system consisting of two forces perpendicular to the y…

A: Forces acting in x direction are Ax+Bx=0Bx=-Ax⋯⋯⋯⋯⋯(I) Forces acting in z direction are…

Q: A block of Weight G is hanged over the two bars 1 and 2 and supported by hanger 3. If the resultant…

A: Point B=0,0,CPoint A=a,b,0Point P=0,b,0Point Q=a,0,0

Q: A dirigible is tethered by a cable attached to its cabin at B. If the tension in the cable is 1040…

A: Take moment about A ∑MA=0Fccos30°(6.7+4)+1040cos30°(6.7)=0Fc=-651.21N

Q: A 30-Ib vertical force P is applied at A to the bracket shown, which is held by screws B and C. (a)…

A: Given Data Vertical force applied at A to the bracket is : P=30 lb Equivalent force system Now…

Q: The force-couple system shown acts on a trapezoidal plate. a. Determine the value of M1 if the…

Q: 4. The block shown is acted on by its weight W = 400 lb, a horizontal force F = 600 lb, and the…

A: The vector sum of two or more vectors is the outcome. It's the outcome of combining two or more…

Q: The bracket, which is fastened to a wall by anchor bolts at A and B, is loaded by the force P = 140…

Q: A dirigible is tethered by a cable attached to its cabin at B. If the tension in the cable is 1040…

Q: Replace the 600 Ib force of the figure by a force through A and a couple whose forces act vertically…

Q: Member BC exerts on member AC a force P directed along line BC. Knowing that P must have a 325-N…

Q: APART FROM THE FORCES APPLIED IN THE FRAME, A 5 KN-M COUNTERCLOCKWISE COUPLE IS APPLIED TO MEMBER…

Question

The force P has a magnitude of 300 N
and is applied at the end C of the rod
ABC, as shown. Assuming a=35° and
B=50°, replace P with
C
B
P
(a) an equivalent force-couple system at
300 mm
В,
(b) an equivalent system formed by two
parallel forces applied at A and B.
A
200 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 1800lbin. couple is applied to member DEF of the pin-connected frame. Find the internal force systems acting on sections 1 and 2.
The figure shows one-half of a universal coupling known as the Hooke's joint. The coupling is acted on by the three couples shown: (a) the input couple consisting of forces of magnitude P, (b) the output couple C0, and (c) the couple formed by bearing reactions of magnitude R. If the resultant of these couples is zero, compute R and C0 for P=750lb.
Detemine the resultant couple moment acting on the plate. Set d= 1.8 m, Fi= 650 N. F2= 250 N and F3= 120 N F1 30 -F: F: 411.3 N.m (CW) 1004 N.m (CW) 1191 N.m (CW) 411.3 N.m (CCW) 1191 N.m (CCW) 1004 N m (CcW
The bracket, which is fastened to a wall by anchor bolts at A and B, is loaded by the force P = 140 N and the couple C = 180 N · m. Replace P and C with (a) an equivalent force-couple system, the force of which acts at A; and (b) two vertical forces, one acting at A and the other at B.
For the system of forces shown, find the equivalent force-couple system at A. If a single equivalent force were to act at D, determine the length from B to D. Note that based on the figure, since there is no given angle for the 150 N force, the manner of 120 N 100 N 60 N B 1m 270 N-m 150 N 120 N D 1 m 0.5 m 0.5 m 2 m which the distance is indicated in the figure suggests that the 150 N force is perpendicular to the 30° arm of the bar system. A 30°
Q4/ Replace the 10-kN force acting on the steel column by an equivalent force-couple system at point O. This replacement is frequently done in the design of structures. 10 kN | 75 mm 1 m
force at point C as shown. Replace this force by an equivalent force- couple system at point O. Ans. M. = 161 i - 165 j+ 120k N•m 300 mm 20° 250 mm 30° F = 800 N
AVERAGE Determine the equivalent force-couple system at A of the system shown on the figure on the right. F3=50 N 4.0 m 2.0 m C. F1=200 N M1=100 N-m 3.0 m -- N 001 =4
Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force, determine the distanced belew point A to its line of action. 100 N 470 mm 470 mm 290 N 470 mm 305 N Answers: Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise. R = i M = N-m Single resultant force. d = i mm
Replace the system of forces acting on the frame as shown by a resultant R at A and a couple acting horizontally through B and C. Force on top 10 kN, bottom left is 40 kN, and bottom right is 50 kN. 1m A 3 m 2 m 4 m OR= 20KN, B = 95KN, C= -95KN OR- -20KN, B = -95kN, C = 95KN OR= 20KN, B = -95KN, C = 95kN OR=-20KN, B = 95KN, C = -95kN mathalino,com
(Q1] (a) Replace the system shown below by a vertical force at D and horizontal force at A and couple. 340 N 500 N 375 mm 760 N - 500 mm 200 mm 600 N