The inlet temperatures for a double-pipe heat exchanger contains water are 35 °C and 200 °C. If their flow rates are 84 kg/h (cold) and 42 kg/h (hot), then; a) Draw the schematic diagrams of counter flow and parallel flow operated for this heat exchanger. b) Evaluate the maximum rate of heat transfer. c) Evaluate the temperatures of water at the outlet of heat exchanger. If it is counterflow, the heat transfer area of heat exchanger and overall heat transfer coefficient are 0.33 m² and 180 W/m².K, respectively.

The inlet temperatures for a double-pipe heat exchanger contains water are 35 °C and 200 °C. If their flow rates are 84 kg/h (cold) and 42 kg/h (hot), then; a) Draw the schematic diagrams of counter flow and parallel flow operated for this heat exchanger. b) Evaluate the maximum rate of heat transfer. c) Evaluate the temperatures of water at the outlet of heat exchanger. If it is counterflow, the heat transfer area of heat exchanger and overall heat transfer coefficient are 0.33 m² and 180 W/m².K, respectively.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.18P

See similar textbooks

Similar questions

Mot water is used to heat air in a double-pipe heat exchanger as shown in the following sketch. If the heat transfer coefficients on the water side and on the air side are 550W/m2Kand55W/m2K respectively, calculate the overall heat transfer coefficient based on the outer diameter. The heat exchanger pipe is 5-cm, schedule 40 steel (k=54W/mK) with water inside.
Water flowing in a long, aluminum lube is to be heated by air flowing perpendicular to the exterior of the tube. The ID of the tube is 1.85 cm, and its OD is 2.3 cm. The mass flow rate of the water through the tube is 0.65kg/s, and the temperature of the water in the lube averages 30C. The free-stream velocity and ambient temperature of the air are 10m/sand120C, respectively. Estimate the overall heat transfer coefficient for the heat exchanger using appropriate correlations from previous chapters. State all your assumptions.
3.34 A flow rate of 1.4 kg/s of water enters the tubes of a two-shell-pass, four-tube-pass heat exchanger at 7°C. A flow rate of 0.6 kg/s of liquid ammonia at 100°C is to be cooled to 30°C on the shell side; U = 573 W/m²K. (a) How large must the heat exchanger be? (b) How large must it be if, after some months, a fouling factor of 0.0015 m²K/W is expected to build up in the tubes but we still want to deliver ammonia at 30°C? (c) If we make it large enough to accommodate fouling, to what temperature will it cool the ammonia when it is new? (d) At what temperature does water leave the new, enlarged exchanger? [(d) TH₂0 = 49.9°C.]
For a 50 m2 tubular heat exchanger operating under the following conditions: Heat Capacity C, kW/K Inlet Temperatures °C Output Temperatures °C Hot Fluid 6 70 X Cold Fluid 3 30 60 a) Calculate the exit temperature of the hot fluid.b) Does the heat exchanger operate in reverse flow or parallel flow or is this not determined from the available information? Answer.c) Determine the total heat transfer coefficient.d) Calculate the efficiency of the heat exchanger.e) What would be the effectiveness of this heat exchanger if its length had been greatly increased? Answer.
Water (Cp = 4200 J/kg. °C) is used cool an unknown fluid (with a given Cp = 3810 J/kg.ºC) using a two-pass parallel flow double-pipe heat exchanger. The unknown fluid enters the heat exchanger at 66 °C with a flowrate of 1.46 kg/s. Water can be supplied at 10 °C and 1.32 kg/s. If the heat exchanger cool the unknown fluid to 39 °C, then the maximum heat transfer between the fluids is equal to 150 kW 230 kW 310 kW 475 kW
Q1: Considering the data below: heat exchanger to cool oil from (60 °C) using water available at (20 °C). The rate of flow of oil is 14 kg/s. The specific heat of the oil is 2200 J/kg K. The overall heat transfer coefficient U= 300 W/m2 K. Determine the outlet temperatures of the fluids. Workout for parallel flow, counter flow and shell with two tube passes.
Table Q3 is given to collect the temperature of hot and cold water at the inlet and outlet positions in the laboratory using Tube Heat Exchanger (TD360a) by varying the cold-water flow rate to investigate the effect of cold-water flow rate on the heat exchanger’s performance. (a) Complete all the output parameters indicated in the table given in Appendix 1. (b) Draw the temperature (TH1, TH2, TC1 and TC2) on the vertical vs position (1, 2) on the horizontal axis for each flow and discuss the effect of cold water flow rate change on the exit temperature of both cold water and hot water. (c) Draw the graph of Energy Balance Coefficient and Mean Temperature Efficiency on vertical axis and cold-water flow rate on horizontal axis. Discuss the effect of flow rate on the Energy Balance Coefficient and Mean Temperature Efficiency based on your finding.
5) During an experiment, a plate heat exchanger that is used to transfer heat from a hot-water stream to a cold-water stream is tested, and the following measurements are taken: Hot water Cold water stream stream 38.9 Inlet temperature, °C Outlet temperature, "C Volume flow rate, L/min 14.3 27.0 19.8 2.5 4.5 The heat transfer arca is calculated to be 0.0400 m. (a) Calculate the rate of heat transfer to the cold water. (b) Calculate the overall heat transfer coefficient. (c) Determine if the heat exchanger is truly adiabatic. If not, determine the fraction of heat loss and calculate the heat transfer efficiency. (d) Determine the effectiveness and the NTU values of the heat exchanger. (Answers: (a) 1724 W (b) 3017 Wiw C (c) the heat exchanger is not adiabatic so heat loss 16.4% and heat transfer efficiency 83.6% (d) effectiveness 44.4% and NTU 0.697) Hot water 38.9°C 19.8°C Cold water 14.3°C 27.0°C
Water (Cp = 4200 J/kg. °C) is used cool an unknown fluid (with a given Cp = 3810 J/kg.°C) using a two-pass parallel flow double-pipe heat exchanger. The unknown fluid enters the heat exchanger at 66 °C with a flowrate of 1.46 kg/s. Water can be supplied at 10 °C and 1.32 kg/s. If the heat exchanger is designed to cool the unknown fluid to 39 °C and the total available length of the heat exchanger is 194 m, the heat transfer surface area of the tube is equal to? Take overall heat transfer coefficient = 564 W/(m2. °C). 15.6 m2
a) In a concentric-pipe heat exchanger, one of the fluids is a condensing vapour and the other is the coolant. Sketch the variation in fluld temperatures of two fluids as they flow through the heat exchanger. Indicate clearly the Inlet and outlet of the coolant and its direction of flow. b) For the case outlined in a) above, the heat-transfer rate, Q, between the two fluids is given by Q =U. Ą ATLI where U, Is the overall heat-transfer coefficient for the heat exchanger, based on the outside surface area of the inner tubo, A, Is the outside surface area of the inner tube and AT Is the relevant temperaturo difference given by ATLM = (T₂-T₁) Tv-T₁ In where subscript v refers to the condensing vapour and subscripts 1 and 2 refer to the Inlet and outlet temperatures respectively of the coolant. 1) State the assumptions used to arrive at the above equation. Explain why the "log-moan" temperature difference above is a more appropriate temperature different for heat exchangers than, say, the…
Counterflow to cool the oil in the lubrication system of a large industrial gas turbine. A double-pipe heat exchanger is used. Coolant flowing through the inner pipe (Cp=4178) J/kg.°C) and oil flowing through the ring channel (Cp=2005.5 J/kg.°C) mass flow rates are 0.2 and 0.4, respectively kg/s. Oil enters the heat exchanger at 60 oC and leaves at 40 oC. Water inlet temperature 30 is oC. The heat transfer coefficient on the ring side is 500 W/m2K. Diameter of thin-walled inner tube is 25 mm, the inner diameter of the outer ring is 45 mm. Pollution resistance in the inner pipe where city mains water is used It is 0.000176 m2K/W. The deposit on the oil side is negligible. a) The heat transfer coefficient in the inner pipe b) Total heat transfer coefficient, c) Calculate the length of the heat exchanger. d) If a 4 m long hairpin is used in the heat exchanger, the required number of hairpins set.
1. 400,000 Ibm/hr of 270°F water is to be heated to 370°F by condensing saturated 390°F steam. (The steam does not sub cool upon condensing). Your job is to design the heat exchanger. The following parameters represent constraint your design. number of tube passes 4 tube fluid water being heated number of shell pass shell fluid steam being cooled U (based on outside tube area) 700 BTU/hr – ft² – °F 1 in tube outside diameter tube wall thickness 1/16 in bulk tube fluid velocity 5 ft/s (a) How many tubes are required per pass? (b) How many tubes are required total? (c) Allowing 3 ft for headers and flanges, how long should the exchanger be?