The modulated signal s(t)=[A1+A2cos(21f1t)]cos(21f2f) was generated by modulating a sinusoidal carrier with single tone message signal. If A1 is 1 Volts, A2 is 7Volts, f1 is 3 kHz and f2 is 756 kHz, then the carrier frequency of this modulated signal is Oa. 5.1429 kHz Ob. 759.00 kHz c. 756.00 kHz O d. 3.0000 kHz

The modulated signal s(t)=[A1+A2cos(21f1t)]cos(21f2f) was generated by modulating a sinusoidal carrier with single tone message signal. If A1 is 1 Volts, A2 is 7Volts, f1 is 3 kHz and f2 is 756 kHz, then the carrier frequency of this modulated signal is Oa. 5.1429 kHz Ob. 759.00 kHz c. 756.00 kHz O d. 3.0000 kHz

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the maximum carrier frequency to be used if the upper limit frequency that is available is 4000 Hz and the frequency of the * ?modulating signal is 100 Hz 400 Hz 3900 Hz 4100 Hz 4000 Hz O
signal subject notice for 2 b(i) use integration way and prove the answer with graph
An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 6MHz. The quantization error in any one sample value must be within ± 0.5% of the peak-to-peak amplitude range of the ADC. How many binary digits must each sample contain? Apply (or equate) the formulas:Δ = Xmax - Xmin / L - 1where Xmax - Xmin = peak-to-peak amplitude range (XRange)eq[n] = Δ/2 (maximum quantization noise)eq[n] = 0.005 XRange
The carrier frequency is 500 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y- axis is the amplitude of the AM signal. Determine the peak voltage level of the modulating signal in V. 3 2 1 -1 -2 -3 -5 0.005 0.01 0.015 0.02 0.025 0.03 0.035 0.04 0.045 0.05 Time (s)
Write an 8051 ASM program to load the timer 1 in order to generate 2000 Hz square wave as given in Figure. The square wave should be generated on pin 2 of port 3. Assume the crystal frequency is 16 MHz. ON 4* Delay Delay
24. In 1 × 4 demultiplexer, the signals given to the input and selection lines are given in the flowing figure; draw the output waveforms of the demultiplexer. lo 12 s Is Data in So S1
A 2 kHz sinewave is mixed with a 1.5 MHz carrier sinewave through a nonlinear device. Which frequency is not present in the output signal? a. 3 MHz b. 3.004 MHz c. 1.498 MHz d. 1.502 MHz
1 6. Calculate the efficiency for each circuit. 7. Name the advantages and disadvantages of each circuit. 8. What is the out frequency of each circuit? 9. Explain how the negative half of the input signal convert in bridge circuit, convert to positive out put. 10. What is the ripple voltage? How can you remove it? 9114.3 -3- AC 1k
perform fo11owing arithmetfe apevatians: (6) (c7e)ic + (BOE)16 using 16's complimeut: -:105 a bujsn ) + (L9L97( II
Define ICBO and ICEO. How are they different? How are they related? Are they typically close in magnitude?
?Which signals are function of time Deterministic signal O Random & Deterministic signal O None of the mentioned,
Home Work 1/ what js meant by Nyquí st rate ? Q2/ what s meant by Pulse Moduletim ? why we need PM?