- The output of a LVDT is connected to a 4 V voltmeter through an amplifier whose amplification factor is 500. An output of 1.8 mV appears across the terminals of LVDT when the core moves through a distance of 0.6 mm. If the mill voltmeter scale has 100 divisions and the scale can be read to % of a division, calculate: (i) The sensitivity of LVDT (ii)The resolution of the instrument in m

- The output of a LVDT is connected to a 4 V voltmeter through an amplifier whose amplification factor is 500. An output of 1.8 mV appears across the terminals of LVDT when the core moves through a distance of 0.6 mm. If the mill voltmeter scale has 100 divisions and the scale can be read to % of a division, calculate: (i) The sensitivity of LVDT (ii)The resolution of the instrument in m

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
H.W3 The single-phase full wave controlled rectifier has a R-L load with R= 0.552 and L= 6.5mH. The input voltage V, 220V at 50Hz. The delay angle is a-30, plot the input and output waveforms. Then determine: -The average thyristor current -The rms thyristor current -The output rms current -The average output current - The efficiency NOTE: Drive any formula that used in solution
Consider the Zener diode circuit shown in Figure. The Zener Breakdown Voltage (Vz) is 5.6 V at Iz= 0.1mA. Zener resistance is rz= 10 0. What is Vo without load (RL= ) ? R= 0.5 ko Vo R Vps= 10 V
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…
The input to a full-wave rectifier is 10 V AC (RMS). The load resistor is 10 ohms. The DC voltage at the output is:
A single-phase full-wave bridge rectifier circuit is fed from a 220 V, 50 Hz supply. It consists of four diodes, a load resistance 20 Q and a very large inductance so that the load current is constant. What is the average or dc output voltage?