The Predator UAV has the following characteristics: wingspar = 14.85 m, wing area = 11.45 m², maximum weight = 1110 kgf, and fuel weight = 295 kgf. The power plant is a Rotax four- cylinder, four-stroke engine of 100 horsepower driving a two- blade, variable-pitch pusher propeller. Assume: the Oswald efficiency factor is 0.7; the zero-lift drag coefficient is 0.03; the propeller efficiency is 0.9; and the specific fuel consumption i 0.2 kgf of fuel per horsepower per hour. Calculate the maximum velocity of the Predator at sea level. The maximum velocity of the Predator UAV at sea level is m/s.

The Predator UAV has the following characteristics: wingspar = 14.85 m, wing area = 11.45 m², maximum weight = 1110 kgf, and fuel weight = 295 kgf. The power plant is a Rotax four- cylinder, four-stroke engine of 100 horsepower driving a two- blade, variable-pitch pusher propeller. Assume: the Oswald efficiency factor is 0.7; the zero-lift drag coefficient is 0.03; the propeller efficiency is 0.9; and the specific fuel consumption i 0.2 kgf of fuel per horsepower per hour. Calculate the maximum velocity of the Predator at sea level. The maximum velocity of the Predator UAV at sea level is m/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A three-blade propeller of a diameter of 1.5 m has a rotational speed is 60 Hz, the activity factor AF is 200 and its static torque coefficient is 0.05. The propeller's integrated lift coefficient is 0.3.
A prototype jet-powered UAV has a wing planform with S = 60 ft2 and b = 20 ft. and an Oswald efficiency of e = 0.82. The aircraft has CD,0= 0.04. The weight is 2,000 lb. For this aircraft, determine the following: a. Minimum thrust required at sea level for steady level flight. b. Velocity of minimum thrust required for the conditions in (a). c. The induced drag for the conditions in (a). d. If Vmax at sea level is 550 fps, what is the thrust available in lb? e. Given the thrust available is produced by a single turbojet engine with a cross-sectional inlet area of Ain= 2.5 ft2, determine the exit velocity from the engine and the propulsion efficiency assuming the exit pressure is atmospheric..
! Required information Problem 06.001 - Calculate thrust required - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL THE PARTS Consider an airplane modeled after the twin-engine Beechcraft Queen Air executive transport. The airplane has the following characteristics: weight is 38,220 N; wing area is 27.3 m²; aspect ratio is 7.5; Oswald efficiency factor is 0.9; and zero-lift drag coefficient CD,0 is 0.03. NOT Th is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Problem 06.001.a - Calculate thrust required Calculate the thrust required to fly at a velocity of 525 km/h at standard sea level. Assume the value of poo = 1.225 kg/m³ at standard sea level. The thrust required to fly at a velocity of 525 km/h at standard sea level is N.
A three-blade propeller of a diameter of 1.5 m has a rotational speed is 60 Hz, the activityfactor AF is 200 and its static torque coefficient is 0.05. The propeller’s integrated liftcoefficient is 0.3. If the aircraft’s lift to drag ratio is 10:1, calculate the requited thrust to weight ratio in orderto active a climb rate that is 8% of the flight speed.
A turbojet engine is being used to propel an aeroplane with the drag of 3900 N and the coefficient of drag is 0.01835. The wing are 21.25m? the air consumption per second of the engine is 14.5 kg/s and threst developed is 8900 N. Calculate the flight velocity and effective jet velocity and also specific thrust.
Problem 06.002 - Calculate total drag An airplane weighing 5,000 lb is flying at standard sea level with a velocity of 525 mi/h. At this velocity, the L/D ratio is a maximum. The wing area and aspect ratio are 200 ft² and 8.5, respectively. The Oswald efficiency factor is 0.93. Calculate the total drag on the airplane. Assume poo = 0.002377 slug/ft³. The total drag on the airplane is lb.
Problem 3 - A small airplane that has a mass of 1,500 lb,m is about to take off. The airplane has a coefficient of lift of 1.0 at an Angle of Attack (AOA) of zero and it linearly increases by 0.1 every 10 degrees; wings with a constant chord length of 3.5 ft and a total wingspan of 30 ft; a coefficient of drag of 0.3; and a frontal area of 40 ft? that linearly increases by 5 ft every 10 degrees. If the air is still, and the density of air is 0.076 lbm ft-3 at the ground level what is the critical speed needed for takeoff? If the runway is 1000 ft long, the total coefficient of friction between the road and the airplane is 0.25, what is the average thrust needed to achieve the critical takeoff speed?
Design the rotor for an aero generator to develop 1000 W at a wind speed of 15 m/s. NACA 4412 airfoil may be used for the rotor. Let us take the design power coefficient as 0.4 and the combined drive train and generator efficiency 0.9. Taking the air density as 1.224 kg/m3
A three-blade propeller of a diameter of 1.5 m has a rotational speed is 60 Hz, the activity factor AF is 200 and its static torque coefficient is 0.05. The propeller's integrated lift coefficient is 0.3.
Problem 05.021 - Calculate induced drag The Cessna Cardinal, a single-engine light plane, has a wing area of 16.2 m² and an aspect ratio of 7.31. Assume the span efficiency factor is 0.62. If the airplane is flying at standard sea- level conditions with a velocity of 290 km/h, what is the induced drag when the total weight is 9800 N? The induced drag when the total weight is 9800 N is N.
Problem 19.2 Moo's Dairy has entered the annual Dairy Drag Race at the State Fair. Her drag racer is a fully-loaded milk truck shown in the figure. When fully loaded, the milk truck weighs 5000 lbf. The truck is a rear-wheel drive vehicle, and the front tires provide negligible frictional drag when rolling. The maximum traction between the tires and the road occurs when there is no slip between the tires and the road, i.e. the force between the road and the tires is due to static friction. The static coefficient of friction between the rubber tires and the concrete pavement is μ = 0.8. a) Determine the reactions between the tires and the road at points A and B, in lbf, when the truck is stationary. b) Determine the maximum acceleration possible for the fully-loaded, rear- wheel drive milk truck, in ft/s² or in g's. Also determine the corresponding reactions at points A and B, in lbf. Is there any danger of the truck tipping under these conditions? Explain. Moo's Dairy da GO dB B da = 4…
7. A 2700-lb car is traveling @ sea level at a constant speed. Its engine is running at 4500 rev/min. and is producing 175 ft-lb of torque. It has a drivetrain efficiency of 90%, a drive axle slippage of 2%, 15-inch-radius wheels, and an overall gear reduction ratio of 3 to 1. If the car's frontal area is 21.5 ft, what is its drag coefficient?