R SITUATION.The propped wooden beam in the figure is fabricated by gluing together three 160-mm by 80-mm planks as shown.Glue10 kNm80 mmNA80 mm80 mm6 m160 mmQ Zoom imageCalculate the maximum shear stressthe glue.1.46 MPa1.30 MPa0.78 MPa0.88 MPa

Answered: Image /qna-images/answer/115490c4-7208-4801-b604-dcfbd3918cb0.jpg

Answered: The propped wooden beam in the figure…

The propped wooden beam in the figure is fabricated by gluing together three 160-mm by BO mm planks as shown. Glue 10 KNm 80 mm NA 80 mm 80 mm 160 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
The lapbelt assembly is to be subjected to a force of 800N. 800 N 45mm SIMI N What is the required lap length d if the glue can sustain an allowable shear stress of 0.74 MPa?
STRENGTH OF MATERIAL(SIMPLE STRESS) PLEASE INCLUDE FBD 100% GUARANTEE UPVOTE
P4.004 A steel bar is attached to a wood support beam with four 20 mm diameter lag screws, as shown in the figure. The steel bar is 60-mm-wide by 5-mm-thick. For the steel bar, the yield strength is 270 MPa and the ultimate bearing strength is 335 MPa. The ultimate shear strength of the lag screws is 165 MPa. Factors of safety of 1.65 with respect to yield strength and 2.8 with respect to bearing strength are required for the bar. A factor of safety of 3.2 with respect to the ultimate shear strength is required for the lag screws. Determine the allowable load P that can be supported by this connection. (Note: Consider only the gross cross-sectional area of the bar-not the net area.) Support beam Ţ Steel bar Answer: Pallow= 0000 KN
A single unequal angle 100 x 75 x 6 is connected to a 10 mm thick gusset plate at the ends with six 16 mm diameter bolts to the 100 mm of leg to transfer tension as shown in figure. What will be the block shear strength (in kN) of the angle section assuming that the yield and the ultimate stress of steel used are 250 MPa and 410 MPa respectively? ISA (100 × 75 x 6) -T 16 mm o bolt 10 mm 40 mm 40 mm| 40 mm 40 mm 40 mm 40 mm 10 mm
1. Figure shows two wood members are joined together using a 60 degrees wood glue adhesive. Find the average normal and shear stress resisted in the plane of the connection. 25 mm 8 kN- 8 kN 60° 30 mm
Two strips of plastic material are bonded together using splice plates as shown. The average shearing stress in the glue must be limited to 1,050 kPa. If P = 45 kN, what splice plate length L is required? a. 142.9 mm b. 149.2 mm c. 192.4 mm d. 124.9 mm
く> Q Search MT ACTIVITY 2M Close Activity File Home Insert Draw View Help Open in Desktop App O Tell me what you want to do v11 I U クv Av S A。ニvニ A Styles v E Tags v abc Calibri ... Teams SW Assignments The composite bar shown in Fig. P-273 is firmly attached to unyielding supports. An axial force P = 50 kips is applied at 60°F. Compute the stress in each material at 120°F. Assume a = 6.5 × 10 6 in/(in-°F) for steel and 12.8 × 10-6 in/(in·°F) for aluminum. 国 Calendar Calls Files ... Aluminum A = 2 in? E = 10 x 10° psi Steel A = 3 in? E = 29 x 10° psi 田 15 in 10 in Help
4. The two pieces of wood, 2 in. by 4 in., are glued together along the 400 joint shown in Figure 4. Determine the maximum axial load P that can be applied if the shear stress in the glue is limited to 250 psi. 600 N a 30° 100 mm 600 N 150mm FIGURE 4
Question j=169" R=2.1" ;f 4- 2.81 d $ 100 08 96 07 h £=0.5" * # >P d=7.3" Material is ASTM A36. Plate is fixed 511 by 4 screws of {"$. using the information provided, calculate the ultimate stress (factored by LRFD) for shear fracture and tensile rupture of block pattern passing through points the shear 3-10-9-4..