The Q = 0.85 m/s the length of pipes 1, 2, 3, 4 and 5 are 1000m,500m, 600m, 800m and 700m respectively. The total head loss in the system is 10 m. and the diameter for pipes 1, 2, 3 and 5 are 90 cm, 50 cm, 40 cm, and 75 cm. respectively. Determine the diameter in pipe 4 if the coefficient of friction in each pipe is 0.020. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: mm Decimal Places required in the final answer: 3 3 4

The Q = 0.85 m/s the length of pipes 1, 2, 3, 4 and 5 are 1000m,500m, 600m, 800m and 700m respectively. The total head loss in the system is 10 m. and the diameter for pipes 1, 2, 3 and 5 are 90 cm, 50 cm, 40 cm, and 75 cm. respectively. Determine the diameter in pipe 4 if the coefficient of friction in each pipe is 0.020. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: mm Decimal Places required in the final answer: 3 3 4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4.5.4. If the pressure difference between points 1 and 2 in Figure P4.5.4 is 25 psi. What will be the flowrate? The pipes are galvanized iron with k, = 0.0005 ft. Take v = 1.06 x 105 ft/s and neglect minor losses. 10 in dia 2000 ft, 8 in dia A B 1600 ft, 6 in dia Figure P4.5.4 C 800 ft, 10 in dia 2.
Three pipes 1, 2, and 3 are connected in parallel and a fourth pipe is connected at B. The difference in head at the ends points A and B is 40m. Given the material properties of each pipe below, compute the following if the friction factor, f = 0.02 for all the pipes: a. discharge of pipe 4.b. total head loss of the piping systemc. diameter of the equivalent pipe with a length of 400m for the entire piping system.
Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of depth is -0.004 ft/s. Determine the cross-sectional area of the tank. The total length of the 0.40-in.-diameter pipe is 18 ft, and the friction factor is 0.03. The loss coefficients are: 0.50 for the entrance, 1.5 for each elbow, and 10 for the valve. A = ft² 3 ft BAMIN Valve
Three pipes 1, 2, and 3 are connected in parallel and a fourth pipe is connected at B. The difference in head at the ends points A and B is 40m. Given the material properties of each pipe below, compute the following if the friction factor, f = 0.02 for all the pipes: a. discharge of pipe 4. b. total head loss of the piping system c. diameter of the equivalent pipe with a length of 400m for the entire piping system.
2. Consider the piping network shown. The pressure heads at points A and B are 80m and 52m, respectively. If the Hazen- Williams Coefficient for all pipes is 110, calculate the flowrate in each pipe. 1 A B 3 2 L₁ = 3000m L2 = 2600m L3 1300m D₁ = 300mm D₂ = 250mm D3 = 200mm
The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
1. Water flows through Pipe A and into parallel pipes 1,2 and 3, and out through Pipe B. The properties of the pipes are listed as follows: Pipe Length (m) Diameter (cm) 30 Friction Coefficient, f A 1 300 10 0.020 240 600 2 15 0.018 3 20 0.017 В 30 The upstream junction (near A) has an elevation of 90m with a pressure of 205 KPa; the downstream junction is at elevation 30 m. If the average velocity in Pipe A is 3.0 m/s, find the pressure at the downstream junctions and rate of flow in each pipe. Also, draw the pipe system.
What is pipe roughness? A pump is located 5 m above the surface = 8170 M/m¹) in a closed tank. The pressure in the space above liquid surface is 35 Kpa. The suction line to the pump is 15 m of 15 cm diameter pipe (/= 0.025). The discharge from the pump is 60 m of 20 cm diameter pipe (/= 0.03). The pipe discharges in a submerged fashion to an open tank whose free liquid surface is 3 m lower than the liquid surface in the pressure tank. If pump puts 1.5 kW Into the liquid, determine the flow rate and the pressure in the pipe on the suction side of the pump. Assume turbulent flow.
absolute roughness is o.03mm (for both sections), Determine the height H. Neglect local losses. Tip: Losses in pipes connected one after another (as in the figure) they add up 2. Consider the system shown. If the flow is Q = 220 lts / s and the H L=500 m D=45 cm L=800 m D=30 cm
A horizontal pipe of 150 mm diameter for the initial 30 m and 75 mm dimeter for the remaining 10 m is connected to a water tank. The height of waler in tank is 15 m above the centre line of the pipe. Find out the flow rate through the pipe, taking all losses into the account. Consider the reduction in diameter of the pipe as sudden coefficient of friction for the pipe is 0.008.
Figure Q4 shows there are two sections of pipes in the system, which are 38m long of 5 cm diameter pipe in section 1 and 45 m long of 15 cm diameter pipe in section 2. The friction factor of pipe in section 1 and 2 are 0.005 and 0.003 respectively. The entrance of the pipe is sharp and the change of section at point C is sudden. There are two 90-degree elbows and an open globe valve in the system. The fitting loss coefficient, k are 0.9 for each 90-degree elbow and 0.25 for open globe valve. If the exit elevation is zero and the flow rate of water is 0.005 m/s. i. Name all the losses in the system with the formula involved, Calculate the total losses in the system, Calculate the power extracted by the turbine if the turbine is 75 ii. iii. percent efficient. 30m Elevation Pipe section 1: 5cm diameter with 38 m long Орen globe Turbine Elevation Om Pipe section 2: 15cm diameter with 45 m long
29 REVIEW INNOVATIONS 2. A pipe 977 m long branches into 3 pipes at junction A. The three pipes span 1046 m, 885 m, and 796 m. They come together at junction B and continue as a single pipe for 1224 m. All pipes are 300 mm in size except the shortest one which is 250 mm. The pressure drop between the junctions is 260 kPa. Friction factor "f" can be assumed 0.02 in the entire system. Calculate the rates of flow in the branching pipes.