The rectangular wood panels is formed by joining two boards together using high strength adhesive in a seam of angle theta as shown in Figure MEC- 106. The working stress of wood is 7.28 MPa, and the normal and shear stresses in the adhesive are limited to 4.83 MPa and 3.10 MPa, respectively. 26 mm 100 mm Determine the maximum value of P if theta is 30 degrees. Select one: O a 18.53 kN O b. 16.63 kN O c. 20 kN O d 16 kN

The rectangular wood panels is formed by joining two boards together using high strength adhesive in a seam of angle theta as shown in Figure MEC- 106. The working stress of wood is 7.28 MPa, and the normal and shear stresses in the adhesive are limited to 4.83 MPa and 3.10 MPa, respectively. 26 mm 100 mm Determine the maximum value of P if theta is 30 degrees. Select one: O a 18.53 kN O b. 16.63 kN O c. 20 kN O d 16 kN

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

Assuming the concrete is uncracked, compute the flexure stresses in the extreme fibers of the beam as shown in the figure for a bending moment of 34 kN-m. The concrete has an f' of 27.60 MPa; determine also the cracking moment of the section. (Use 0.62 1 = 0.70 in calculating the modulus of rupture). Dimensions are in millimeter. 380 455 3 #9 bars (A, = 3.00 in.2) 75 300
Assuming concrete is uncracked. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 1x10°kg cm . Determine the cracking moment of the section. A = 10cm² %3D E, = 2*10°kg / cm² E = 2*10°kg / cm² %3D %3D f'. =1836kg / cm² %3D 90 cm 100 cm 40 cm
Question 2A composite bar is made up of a steel strip 2 mm thick and 12 mm wide, sandwichedbetween two aluminium strips each 3 mm thick and 12 mm wide. The three strips areheld together by two rivets of 5 mm diameter each.2.1 Make a neat detailed sketch of the assembly.2.2 If the three strips are fastened together at 15 0C, determine the shear stress set up inthe rivets when the temperature is raised to 21 0C.Note: The resistance of a rivet in double shear may be taken as 1.75 times the resistancein single shear.(For steel: E = 200 GPa and α = 11×10 -6/ 0C)(For aluminium: E = 70 GPa and α = 22×10-6/0C)
A pretensioned member with a dimension of 250mm x 360mm is subject to an eccentric tendon that is located 105mm from the soffit. Area of the prestressing steel to be 502 sq. mm and the modulus of elasticity is 200 GPa. The Modulus of elasticity of concrete is 36.8 GPa. Creep coefficient = 1.6 and the shrinkage strain = 3 x10^6. Assume a 5% steel relaxation. Find the total prestressed loss in percentage.
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
A rectangular pretensioned beam has concentric prestress force of 1000 KN. The beam is 300 x 500 mm in dimension and M20 grade of concrete is used with creep coefficient of 1.6 and residual shrinkage strain of 3 x10-4. Ast = 500 sq.mm. Find the following: a. Loss due to elastic shortening use Est = 200 GPa and Ec = 5700(Fc)^1/2 b. Loss due to creep c. Loss due to shrinkage d. Total loss of prestress
– A joint is made by gluing two plywood gussets of thickness t to wood boards.The tensile working stresses are 1200 psi for the plywood and 700 psi for the woodboards. The working shear stress of the glue is 50 psi. Determine the dimensions’ b and tso that the joint is as strong as the boards.
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.
The wooden beam shown is made by gluing together planks as shown. 8 kN/m Glue 80 mm A B 80 mm - NA 6 m 80 mm 160 mm Determine the maximum shear stress in the glue in kPa. (2 decimals)
A composite beam is constructed using a steel plate (10 mm x 145 mm) with two wood beams (75 mm x 145 mm) on either side. The wood and steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M₂ = 7.45 kN. m. ź Steel Wood i Calculate the maximum tensile and compressive stresses in the wood and steel if Ew = 11 GPa and E = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention. Use the general theory for composite beams described in the textbook.) maximum tensile stress in wood MPa MPa maximum tensile stress in steel maximum compressive stress in wood maximum compressive stress in steel MPa MPa Need Help? Read It
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D
Two pieces of wood are glued together, find the maximum load which the glued wood could carry that must not exceed 12 MPa normal stress and 7 MPa shear stress. P 30° P 100 mm Glued Section 100 mm