The rigid bar AB, attached to aluminum and steel rods, is horizontal before the load P=141 kN is applied. Find the vertical displacement of point C (in mm) caused by the load P.  LA=2,9 m;   LS=3,48 m; AA=272 mm2;   AS=435,2 mm2; EA=70 GPa;   ES=200 GPa; L1=2,1 m;   L2=1,68 m;

Q: Q // The mechanism shown in the figure below has 0.02 in. gap at 80 Fahrenheit degree, find (a) the…

A: Given Data :              δ  = 0.02 in              LB = 16 in…

Q: A solid circular bar is surrounded by a layer of copper rigidly attached to it, the assembly is…

A:

Q: A solid copper bar of circular cross sectionhas length L =1.25 m and shear modulus of elasticityG =…

A: Shaft is designed on the basis of following two criteria:- Strength Criteria According to Strength…

Q: Steel L= 4m Aluminum L= 3m A= 300 mm? E= 200 GPa A= 500 mm? | E= 70 GPa A 3.5 m 2.5 m

A:

Q: In the figure below, a pulley can pull a 1-ton load from rest to 3 m/s upwards at 2 seconds. AB and…

A: Given: The load, W = 1 ton The speed, v = 3 m/s The time, t = 2 s The compressive stress, σ = 140…

Q: Q.3 A steel column (E = 30 x10 3 ksi) that is fixed at the base and free at the top is constructed…

A:

Q: The figure below is a schematic drawing of a shaft that supports two V-belt pulleys. The loose belt…

A: Given, The yield strength of the material, sy=300 MPa The ultimate strength of the material, su=520…

Q: applied Q2: A (500*400) mm column shown in Fig.2 is reinforced with 12 32mm bars. service dead load…

A: Given Datab=500mmd=400mmAst=12-ϕ32mmfc=25MPafy=400MPa

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

A: A pin support will exert both horizontal and vertical components of reaction as the reaction forces.…

Q: Q3/ A truss shown in Figure below is made of Aluminium and it consists of two rods. The…

A:

Q: (ABCD) which was supported thru pin at B. Two bars was also connected, Bar CE and Bar DF with…

A: The diameter of the pin B can be calculated using the formula given below as- τs=FrA where, τs is…

Q: round bar of length L. modulus of elasticity E, and weight density tapers uniformly from a diameter…

A: Given:Length of round bar=L,Modulus of elasticity= E,Weight density=γ,Diameter at one end=3DDiameter…

Q: B D F 0.5 m E G 0.2 m 0.3 m 0.3 m tP=90 kN

A: NOTE:- As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost…

Q: A bar ABC of length L consists of two parts of equal lengths but different diameters. Segment AB has…

A:

Q: The mechanism shown

A: Write the expression for the compressive reaction force from the support when the stress in the…

Q: The Uniform AB brass bar is fixed with support and pin as shown in the figure and has a rectangular…

A: Given data: (a) Write the expression for the critical load in the horizontal direction.

Q: The rigid bar ABC is supported by pin at A and aluminium wire BD, is horizontal betore the Load P is…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A vertical steel bar shown in figure Q1 is subiected to a compressive load of 75 kN. If the stress…

A:

Q: A vertical steel bar shown in figure Q1 is subjected to a compressive load of 75 kN. If the stress…

A: Given data: F=75 kNδ=0.04 mmE=200 GN/m2 Need to determine the cross-sectional dimensions and length…

Q: 1. The 30.0-mm-diameter steel rod whose E = 150.0 GPa is subjected to the axial forces shown in the…

A:

Q: A copper bar of 20 mm dia is tightly fitted inside a steel tube of external dia of 30 mm. the length…

A: Given: P=60KN Es= 200KN/mm2 Ec= 160 KN/mm2 di=20mm do = 30mm area of copper(Ac) = π/4*di2 =…

Q: This subject is strength of materials show complete and clear solution with free body diagram and…

A:

Q: A steel bar 500 ft long, suspended vertically from one end, supports a load P at its lower end. The…

A:

Q: A steel bar with diameter d1 = 10 mm has upset ends with diameter d2 = 15 mm. The lengths of the bar…

A: Given that, d1=10 mm,d2=15 mm,L1=0.3 m,L2=0.15 m,R=1.25 mm,E=90 GPa,δ=0.5 mm,

Q: A solid steel bar of diameter d, = 26.0 mm is enclosed by a steel tube of outer diameter d diameter…

A:

Q: The circle ring whose one end is fixed and the other end is free, acting on the shaft torsional…

A:

Q: The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional…

A: GivenW=44kNA=178.5mm2E=71GPa

Q: The pin connected structure shown in the figure consists if a triangle shaped rigid bar, a cast iron…

A:

Q: A bar ABC length L consists of two parts of equal lengths but different diameters.Segment AB has…

A: Given: P=110 kN shortening of the bar = 0.8 mm (a)Maximum allowable diameter (b) distance b from…

Q: A circular column is made of concrete [E. = 4.2(10³)ksi] while being reinforced with six steel rods…

A: I have attached my answer below, please refer and give me +ve rating, Thanks!

Q: Q / The figure below shown that the three bars are supported a rigid beam ACE. The bar CD is made of…

A:

Q: Q For the assembly shown in the figure, brass rod AE (E=105 GPa) and aluminum rod BF (Ea=70 GPa)…

A:

Q: The horizontal member shown in the figure is loaded by 25 kN at E. It is supported by steel…

A: Permissible stress is stress, which produces due to pressure or forces which does not exceed the…

Q: 3. A cylindrical rod is fixed between two walls. The rod is composed of two materials. Section AC is…

A:

Q: The figure shown below

A: The cross-sectional area of the bars is Consider the diagram shown below for the beam ACE, Taking…

Q: A round bar of length L. modulus of elasticity E, and weight density y tapers uniformly from a…

A: Given:d1=3Dd2=2D

Q: Four steel bars jointly support a mass of 15 Mg as shown in Fig. P-276. Each bar has a…

A: As per given question  α=11.7 m•c E=200gpa ΔT=50°c We have to find load carried by each bar

Q: 3. The rigid bar BC in the figure supported by the steel rod AC of cross -sectional area 0.25 in?.…

A:

Q: The Uniform AB brass bar is fixed with support and pin as shown in the figure and has a rectangular…

A:

Q: The homogeneous bar shown in Fig. P-106 is supported by a smooth pin at C and a cable that runs from…

A:

Q: The figure below shows a section of a column subjected to load P, which is applied 50 mm from the…

A: Given: Distance of the load from the from the middle of the section's web: →r=50 mm=0.05 m Area of…

Q: Figure Q3 shows a steel bar of diameter 16 mm and length 600 mm subjected to axial forces If E =…

A:

Q: The rigid bar AB, attached to aluminum and steel rods, is horizontal before the load P=140 kN is…

A: Given Data: The length of the aluminium and steel rods are LA=2.9 m and Ls=3.48 m. The area of…

Q: 1.39 Find the spring constant of the bimetallic bar shown in Fig. 1.89 in axial motion. 2 cm -Steel,…

A:

Q: Q3) A short stepped bar is shown in Figure below. The stiffness of the large section is 12 kN/mm and…

A:

Q: Assume portion ABC of the rod is made of steel (Ee= 200 GPa , v=0.3) and portion CD is made of…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.