The rigid block of mass M is supported by the three symmetrically placed rods. The ends of the rods were level before the block was attached. Determine the largest allowable value of M if the properties of the rods arc as listed (sigma w, is the working stress)

Q: 2. A coupled mass-spring system is shown below. The masses are m, = 25 kg and m = 45 kg. The spring ...

A:

Q: What defines the combustion chamber of afour-stroke engine?

A: Given data : Combustion chamber of four stroke engine.

Q: The 20 mm diameter steel shaft AB is attached into the rigid wall at B and supported by a smooth bea...

A: Answer: The downward force P is 1212.85 N.  

Q: A distance was measured with an electronic infrared device, during which the influential weather ele...

A: the correlation is calculated from the following relation:   where,∆t= 32-26 = 6°C∆p = 670-680 = -10...

Q: The stress field in a loaded aluminum plate was determined as [-2x² + 3y² 3x + y + 5 3x + y + 5 -2y2...

A:

Q: [2] Using the method of joints, determine the force in each member of the truss shown State whether ...

A:

Q: Identify the applications, accuracies and limitations of the different pressure measuring instrument...

A:

Q: uniform supersonic flow of a perfect gas with y = 1.4, a Mach number of 3.0, and an up- eam static p...

A:

Q: In a reheat cycle steam at 8.0 MPa and 485C enters the turbine and expands to 1.4 MPa. At this point...

A:

Q: Two identical, simply supported beams ABand CD are placed so that they cross each other attheir midp...

A: Consider a simply supported beam where a uniformly distributed load having magnitude 'ω' is applied ...

Q: At a standard sea level, the specific heat ratio is 1.4, temperature at  and the universal gas const...

A: At standrard sea leavel, the specific heat ratio is 1.4,temperature at 15°C.

Q: Problem # 3, at 15.85 °C and 101.3 an air - wate vaper @ saturatin 350 kilo pascal the liguid mistur...

A: Calculate the total pressure of final mixture. Pv=160+1.8=161.8 kPa

Q: What is the main cause of the increase in drag when you increased the angle of attack?

A: Drag is the aerodynamic effect that affects the motion through air. It is generated due to relative ...

Q: find the value of the force F

A: Find the value of force.

Q: What is the difference between ultimate consumers and organizational buyers?

A: Given Data : Ultimate consumers  Organizational buyers  

Q: The in-cylinder pressure of an engine has been measured at both TDC and BDC, which are P1 = (1.0000x...

A:

Q: 3. The tape shown slides around two fixed pegs each of radius 30 mm as shown. If T1 = (0.1P in newto...

A:

Q: As a part of an assembly process, the end effector A on the robotic arm as shown in Figure 5 needs t...

A:

Q: A specimen of a methacrylate plastic is tested in tension at room temperature (see figure), producin...

A:

Q: The speed of sound in a solid medium is given by the formulae v = of Young's modulus for the solid a...

A:

Q: A strain gauge is used to measure the shear strain on a shaft during torsional loading. The strain g...

A:

Q: Design the gearbox used in modern cars and also state its working principle.

A: Definition: A device must be authorized to enable the engine crankshaft to revolve at a relatively h...

Q: Q14a. If the resultant vector force (R) acting on body P is 225 N at 50° relative the x-axis, and F1...

A:

Q: 3. A model for an airplane's pitch loop is shown below. find the range of gain K that v Can the syst...

A:

Q: The crank link AB of the crank and slider mechanism has an angular velocity of 7 rad/s“, both direct...

A:

Q: Properties of Pure Substancies What is the specific internal energy of water at 50 kPa and 20°C?

A:

Q: What advantage might the commercially packaged coolant material have over ice other than it produces...

A: Advantages that commercially packed coolants have over ice: 1. One of the major disadvantages of usi...

Q: What is screw transformation matrix, in a screw transformation, prove that Trans(A, i) x Rot (ø, 3) ...

A: What Is a Transformation Matrix? Changes are utilized to plan an image into another with various siz...

Q: The 20 kg block D is dropped from a height h onto the steel beam AB. Additional data are: h= 500 mm ...

A: When a mass 'm' falls at a height 'h' on the beam then deflection produced in the beam is known as d...

Q: Steam is the working fluid in an actual Rankine cycle. Steam enters the turbine at 8.0 MPa and 550 d...

A:

Q: A composite cube with 40-mm sides and the properties shown is made with glass polymer fibers aligned...

A: Write the given data. Ex=50 GPaEy=15.2 GPaEz=15.2 GPaνxy=0.254νxz=0.254νxy=0.254νzy=0.428

Q: Design a piston for use in automobile engines (piston ring, pin, skirt).

A:

Q: for the enhancement of load bearing capability of composite materials

A: b: explaion with detail sketches why length and diameter of the fiber matrial plays the vidal roles ...

Q: What are common efficiencies for transformers?

A: Given data : Transformers

Q: A 3.25 – meter steel column was placed between two concrete blocks at 20. 6°C. Calculate the gap nee...

A: Consider a prismatic bar having length(l), width(b) and height(h) in x,y and z directions respective...

Q: s the confidence level for

A: Determine the confidence level.

Q: he Lookout Hills gravitational slope-deformation feature in Bonne Bay, western Newfour plume of rock...

A: 306m wave height has been found in norris point. 

Q: A steel tube with a circular cross section has an outside diameter of 294 mm and wall thickness of 2...

A:

Q: Although the information from different publishers vary in presentation and the arrangement of _____...

A: Although the information from different publishers vary in presentation and the arrangement of words...

Q: How the power has to be transmitted from one shaft to the other which are intersecting in vehicles d...

A: In mechanical arrangements, there would be situations where intersecting shafts have to be connected...

Q: A vapor-compression refrigeration system uses the arrangement shown in Fig. 10.10 (a flash chamber a...

A:

Q: Consider rectinear motion using the motion of the derivative of a vector. In particular, determine e...

A:

Q: When using a fuel injector pulse tester, Technician A says that little or no pressure drop indicates...

A:

Q: Meaning of 316 in E316T-1

A: Given data : E316T-1

Q: A plane frame with a pin support at A androller supports at C and E has a cable attached at E,which ...

A: Cable force F=400NAB=4mBC=3mCD=4mCE=5m To-Find:-  (a) Find reactions at supports A, C, and E. (b) Fi...

Q: Calculate the change in entropy of air, if it throttled from 5 bar, 27°C adiabatically. to 2 bar

A: We must compute the change in entropy of air if it is adiabatically throttled from 5 bar, 27oC to 2 ...

Q: QUESTION 3 A 300mm x 100mm channel section is used as a short vertical column. The column is to carr...

A: given; →dimension ; (b*d)=300mm*100mm→width(b)=300mm→depth(d)=100mm→compressive load (P)=500KN      ...

Q: he shear strain of the element and the normal strains of the diagonals AC and BD. The initially squa...

A: Giveninitial diagonal of square elemnet AC=BD=2mmafert defornationAC=2.015mmand BD=1.995mm

Q: 6 shifts/wk. The repositioning time is 0. cations. Immediate Work Te (min) Immediate predecessors el...

A: Hi and thank you for the questions. Since you have asked multiple questions and not specified which ...

Q: Q4- Explain the following state "other mechanical properties often may be estimated from hardness da...

A: As per the Bartleby answering guidelines we are supposed to answer first Question only.Please repost...

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.