The shaft in (Figure 1) is used to transmit 32 hp while turning at 600 rpm. Figure 2 in. 2.5 in. 1 of 1 Part A Determine the maximum shear stress in the shaft. The segments are connected together using a fillet weld having a radius of 0.18 in. Express your answer to three significant figures and include appropriate units. Tmax= Submit μA Value Request Answer Units < Return to Assignment Provide Feedback ?

The shaft in (Figure 1) is used to transmit 32 hp while turning at 600 rpm. Figure 2 in. 2.5 in. 1 of 1 Part A Determine the maximum shear stress in the shaft. The segments are connected together using a fillet weld having a radius of 0.18 in. Express your answer to three significant figures and include appropriate units. Tmax= Submit μA Value Request Answer Units < Return to Assignment Provide Feedback ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An element made of AISI 1020 CD steel is shown, but to shape it, it had to be machined. It must have a reliability of 99.9999%.It is subjected to the loads P₁= 200 pounds and P₂= 400 pounds; In others, the force in the "z" direction does not act, but the force in "y" remains with the same magnitude, but is completely reversed, in the positive and negative sense of the "y". Determine:to. The critical point of the system and for this establish the state of effort. Explainb. Apply Mohr's circle to the critical stress state and obtain σ1, σ2 and tmaxC Determine the safety factor and explain.
X 27. Determine the diameter of the stud bolt that are required to fasten down the cylinder head of a 203 mm x 304 mm gas engine. There are ten bolts on the block. The explosion pressure is 31 kg/sq cm and studs are made of ordinary bolts material SAE 1020. How deep should the bolt be drilled? B. 40.2 mm C. 37.3 mm D. 35.5 mm by a motor at 400 mm raises the attached load of 000 t 28 A. 38.1 mm. A double thread Arme screw driven
1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
QUESTION 1 Based on Figure 1, analyze the state of stress at material element of point A on the cross section of the pipe at section a-a. Note that / is the location of applying load to adjust the resultant torque. Given that /= 250 mm and e = 30°. i) The required minimum shear stress at point A to loosen the pipe is tegd = 1 MPa. Decide and explain either torque applied is appropriate or not. If yes, determine the minimum value of I when 8 = 90°, or if not, determine the maximum value of / when 8 = 90°. i) Suggest one material from Appendix C that is suitable to be used as material for the pipe in Figure 1. Explain your selection. 25 mm B 300 N 30 mm Section a-a 300 mm Figure 1
Assume a suitable value if any data is found missing. Two cylindrical pipes are to be used to make a medium drive fit. The nominal diameter of the assembly is 200 mm. The outer diameter of the outer pipe is 230 mm and the inner diameter of the inner pipe is 150 mm. Both the inner and outer pipes are made or aluminum. Assume that both the members have dimensions according to the prescribed tolerances for the kind of fit, determine the maximum and the minimum possible tangential stress in the outer cylinder.
Question 15 Calculate the maximum stress in the diagram below, considering stress concentrations. 0.10-in radius 2.00-in dia. 1.25-in dia. Applied torque = 2200 lb.in
Manual Calculation 2: Refer to image shown. Decimal Places: 2 Use hand calculations, modeling is not necessary The "Shaft" carries a torque that induces a shear force in the "Bolts". Shear Stress in the 4 bolts (kN/m³) S = 40,000 "Bolt" spacing (m) C = 0.24 "Bolt" diameter (mm) d = 30 "Shaft" diameter (m) D = 0.15. Assume each "Bolt" carries the same shear force. What is the Torque (kN-m) carrying capacity of the shaft? 4 Typ (d) Bolt Shaft
+0.10 -0.05 The dimensions for the shaft size are 020 1. mm and the hole size are 020 mm. -0.10 Find the maximum and minimum limits of hole and shaft. Find the tolerance for the hole and shaft. Find the type of fit and draw the diagram for shaft and hole.
1-69.M Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be if the circular shank of the bolt pulled out from the head, a shearing action. Compute the shear stress in the head for this mode of failure if a force of 22.3 kN is applied. Applied force Shear area Reaction force on underside of head Cylindrical shear area 19.0 mm 8.00 mm -12.0 mm M12 x 1.75 thread
What is the design stress in psi of an ASTM A313, gage number 8 spring wire. The type of application requires a factor of 0.34 for the type of service. Round your answer to 4 significant figures.
A straight spline has 10 splines and is Fit B. The required major diameter, D, of this spline subject to a torque capacity per inch of length of spline of 600 lb-in is most likely: O 0.8 in O 2 in O 1.4 in O 1.7 in
The couple moment acting on the pipe has a magnitude of 180 Nm (Figure 1). Figure -F A -150 mm. 150 mm B F 200 mm 600 mm 1 of 1 Part A Determine the magnitude F of the forces applied to the wrenches. Express your answer to three significant figures and include the appropriate units. F = Submit 0 μĂ Value Request Answer < Return to Assignment Units Provide Feedback ?