The solid hull of a boat has cross sectional dimensions of 10 ft wide by 6 ft high. It has a draft of 5 ft in water and its length is 30 ft. Considering the longitudinal axis of the hull for initial (upright) and tilted positions, determine the following: (a) initial GB (ft), (b) initial MB (ft), and (c) initial MG (ft). Determine the following when the angle of tilting is 10°. (d) MB (ft), (e) MG (ft), and (f) RM or OM (ft-lb)

The solid hull of a boat has cross sectional dimensions of 10 ft wide by 6 ft high. It has a draft of 5 ft in water and its length is 30 ft. Considering the longitudinal axis of the hull for initial (upright) and tilted positions, determine the following: (a) initial GB (ft), (b) initial MB (ft), and (c) initial MG (ft). Determine the following when the angle of tilting is 10°. (d) MB (ft), (e) MG (ft), and (f) RM or OM (ft-lb)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The continuous beam is loaded as shown below. a. b. C. determine the moment at point 1 (M₁) determine the moment at point 2 (M₂) determine the moment at point 3 (M3) T Ri 2M 70kn/m R2 фоко/м 2M ·Im R3
The automobile bumper jack is designed to support a 3540-N downward load. Begin with a free-body diagram of BCD and determine the force supported by roller C. Note that roller B does not contact the vertical column. E 175 mm 175 mm B Answer: C- i O 460 mm -A 3230 mm 3540 N D N 100 mm 240 mm F
A rectangular beam has a width of 300 mm and an effective depth of 500 mm. It is reinforced with 4-32mm Ø bars at the tension side and 2-16mm Ø bars at the compression side. Top bars are placed 65mm from the top of the beam. f=25 MPa, fy = 415MPA. Which of the following corresponds the location of the neutral axis from the top of the beam?
A flat steel plate is of trapezoidal form and uniform thickness of 10mm. The plate tapers uniformly from a width of 150mm to 100 mm over a length of 500mm. Determine the elongation of the plate under an axial pull of 100 KN. Take E= 200 KN/mm² B₁ 100 KN I -x-8x 100 mm 500 mm- 150 mm B₂ 100KN
A simply supported beam of length L is subjected to a varying distributed load sin(3rx/L)Nm, where the distance x is measured from the left support. The magnitude of the vertical reaction force in N at the left support is (a) zero (b) L/3л (c) L/t (d) 2L/T
A cylindrical tank is at rest as shown. The tank has a weight of 100 kN. Ap- proximately what horizontal force should be applied horizontally at point C to raise the tank? F 8 m A W 4 m
4 - A rubber material is attached between two rigid plates. If the lower plate is held in place, what load P is needed to produce a relative displacement of 0.5 mm between the two plates? The rubber material has a shear modulus G = 0.0010 GPa. 80mm 200mm 400mm
Determine (a) the equation of the slope and deflection of the elastic curve for the simply supported beam, and (b) the slope and deflection at 5 meters from A. The modulus of elasticity and the moment of inertia about the neutral axis of the beam are 150 GPa and 70 x 106 mm4, respectively. 6 kN/m 3 kN/m E B C AD 4 kN/m 3 m 4 m 3 m
H.W.4: For the propped cantilever beam shown in Figure assume that EI = 100,000 kip-fi® and use discontinuity functions to determine (a) the reactions at B and D. (b) the beam deflection at C. % ‘ 5 kips/ft 10t 21 8f
Five forces are applied to the beam trolley as shown. Determine the y-coordinate of the point on the y-axis through which the stand-alone resultant R must pass if F = 6.0 kN and θ = 40°. Point O is at the center of the I-beam.
A cantilever beam of span karries a concentrated load Pat its free end. Which of the following gives the slope at the free end of the beam? Select the correct response. PI/2EI PI/El ) PRAZE () P/4El
2. For the beam shown, calculate the support reaction. 2000 Ib 500 Ib/ft A B 6- ft ft