The steel beam has the cross section shown. The beam length is L = 6.4 m, and the cross-sectional dimensions are d = 345 mm, b=205 mm, t = 16 mm, and tw = 7 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 215 MPa. Wo

The steel beam has the cross section shown. The beam length is L = 6.4 m, and the cross-sectional dimensions are d = 345 mm, b=205 mm, t = 16 mm, and tw = 7 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 215 MPa. Wo

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. An ASTM A36 structural steel beam 5.00 m long is placed between two rigid supports. When the temperature is 20°C, there is no stress in the bar. Compute the stress developed in the beam if the temperature rises to 45°C. Assume that the proportional limit is 235 MPa. a = 11.7 x 10-6 1/C° E = 207 GPa
Find the lightest S-shape for the beam shown if the working stress in bending is 175 MPa. What is the maximum bending stress in the beam selected? Please answer this with FBD please. Thank you.
Question 3 A pair of lateral load is applied to a 3 m steel beam as in Figure Q3a to bend it plastically. The beam has a solid rectangular cross-section (30mm x 50mm) as in Figure Q3b. The steel behaves in elastic-perfectly plastic behavior with Yield Stress of 200 MPa. When 50% plastic condition at critical section, determine: a. the value of load P b. the Yielded Length, Lp corresponding to condition in part (a). 1.5P P 1m 1m Figure Q3a 1m 30mm 50mm Figure Q3b
A hollow cylinder with an OD of 100mm and an ID of 30mm, supports a load of 100kN. What is the compressive stress in MPa? I am new to the subject but why use .....AC = π * (D2 - d2) / 4 instead of A = π(r12 - r22) to find the cross sectional area of a hollow cylinder ?.
Practice 2 A fixed ended steel beam 8m long carries a uniform load 20kN/m and an axial tensile force of 200KN. The properties of steel section is as follows: A = 7800 mm? d = 324 mm Ix = 140x10 mm ly = 16x10 mmt What is the axial stress of the beam, in MPa. What is the actual bending stress in the beam due to uniform load alone acting on the beam, in MPa. -. What is the interaction value if Fb = 210 MPa and Ft = 100 MPa? answer key а.)25.64 Мра b.) 123.43 Мра c.) 0.844
A steel bar 30 mm in diameter and 2 m long is encased in a shell of cast iron 5 mm thick. Compute the stress in each material, in MPa, if a compressive axial load of 150 kN is applied to the assembly. For steel, E = 200 MPa and for cast iron, E = 100 %3D GPa ( Select the correct response(s): 29.96 MPa 76.39 MPa 212.21 MPa 106.10 MPa 136.32 MPa 152.79 MPa 59.92 MPa 272.84 MPa
An aluminium channel section is shown in the figure below: mm 1; mm mm li mm As indicated, the horizontal sides are of length / = 167 mm and thickness 1 - 1 mm while the vertical side is of length l2- 218 mm and thickness 12 - 3 mm. Determine the shear stress in the top side when it is subject to a pure torque of 20 Nm. You may assume that the factor ki may be taken as 0.333. Give your answer in N/mm² to three decimal places.
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
A rectangular column section is as shown in the figure. 200 mm y There is a load of 200 kN, acting on the cross-section with an eccentricity of 60 mm along x-x axis as shown. Then For no tension in the given section, the eccentricity should be less than 33.33 mm Correct Option B Maximum stress for the section is 7 MPa (compression) Correct Option C Minimum stress for the section is 2 MPa (compression) D Stress at the layer parallel to weaker axis at a distance 80 mm in the direction of eccentricity is 6.1 MPa Correct Option 400 mm
A small aluminum alloy [E = 73 GPa] teeshape is used as a simply supported beam as shown. For this beam, a = 150 mm. The cross- sectional dimensions of the teeshape are b = 25 mm, d= 38 mm, and t=7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 490cis measured from a strain gage located at c= 9 rmm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d a a H Answer: P = i
An aluminum bar having a cross-sectional area of 160 mm² carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2= 1.0 m; B3= 0.6 m. Determine the axial stress of bar B3 in MPa. 35KN B1 B2 B3 10KN 15KN 30KN
(b) Figure Q4(a) shows a steel beam with length of 4 m that is supported by a steel column at point B. The steel column of AB has a rectangular cross section (40 mm× 70 mm). The ends are assumed to be pin connected. The yield stress of steel is o y = 250 MPa. The Modulus Elasticity of the steel is 200 GPa. Use factor of safety of 1.5. (i) Check whether the Euler's equation is appropriate or not. (ii) Determine the maximum distributed load (W) that can be applied to the beam so that the column of AB does not buckle.